Search Documents

By Paul E. Blackburn, Joan B. Berkowitz-Mattuck, Edward J. Felten

The oxidation behavior of MOSi2 has been studied between 450° and 650°C, the temperature region where "pesling" occurs. Disintegration ("pest-ing") of MoSi2 is shown to occur in the presence of oxygen, but not nitrogen, carbon dioxide, carbon monoxide. or argon. The rate of disintegration is extremely sensitive to oxygen pressure. The crack density of polycrystalline MoSi2 increases ivith lime at temperature. All kinds of cracks are observed: THE excellent oxidation resistance of MoSi, at temperatures of 1000 to 1700°C promises to have important technological benefits. However. the ap- Ihose which are confined within a single grain, those that ci'oss grain boundaries transversely, and those that follow grain boundaries. Laue photographs verify the existence of Iranscryslalline cleavage. Single crystals of MOSi2 do not "pest". Tlrcd solrlbility of oxygen in MoSi2 is extremely low, no lattice changes being observed as a result of exposure of MoSi2 to oxygen in the "pest" temperature range. plicability of MoSi2 is somewhat restricted by the occurrence of a completely destructive oxidation of the intermetallic phase at intermediate temperatures (300" to 6003C). This phenomena was ternled to be the "MoSi2 pest" by Fitzer who first observed it.' Molybdenum disilicide is a metallic material in both physical appearance and electrical properties.

Jan 1, 1965

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By William Klement

KNELLER' has recently reported that extensive metastable solid solutions may be obtained in Cu-Fe alloys by simultaneous vapor deposition. This note reports that solid solutions, apparently single -phase, can be obtained for Cu-Fe alloys containing 0 to 20 and 85 to 100 at. pct Fe by rapid quenching from the melt; the inability to extend the solid solubilities further is related to the liquid miscibility gap, Fig. 1, as for Cu-Co alloys.2'3 Accurate lattice spacings of the copper-rich fcc and iron-rich bcc solid solutions have been obtained. Homogeneous alloys were prepared by casting4'5 and sintering2 from elements of 99.9+ pct purity. The quenching techniques were as before,' except the iron-rich alloys were liberally covered with argon while at elevated temperatures. Flakes about 1 sq mm in area were obtained and investigated with the Debye-Scherrer technique, as previously described.2,4 All X-ray work was done at 25° 2°C using filtered copper and cobalt K radiation. Relative visual intensities of the diffraction lines for the phases in the quenched alloys are shown in Table I. The lattice spacings of the fcc structure for alloys containing up to 80 at. pct Fe are plotted in Fig. 2. The variation of these lattice parameters with composition is in good agreement with the re- of cementite spots usually present (all hkl reflections are allowed) and the ease of confusing them with ferrite or martensite reflections. Copies of the report can be obtained by writing to the Materials Research Department, Rocketdyne. 6633 Canoga Avenue, Canoga Park, Calif., 91304. A copy is also available at the Engineering Societies Library, 2nd floor, 345 East 47th Street, New York, N.Y., 10017. Photocopies, either full-size or microfilm, may be purchased from the Engineering Societies Library. sults6 of Andersen and Kingsbury, Fig. 2, although there is some disagreement in absolute value. This discrepancy may be due to the different temperatures at which the X-ray measurements were carried out and perhaps to the different extrapolation procedures. Also, Andersen and Kingsbury6 state that their lattice spacings were computed relative to the wavelengths given by Siegbahn in 1933; this reference has not been found and it is assumed that the well-known 1931 wavelengths were used, the lattice spacings then being in kx units which are converted into angstroms by the factor 1.00202. There is no support for the contention that solution of iron decreases the lattice parameter of copper, as con-

Jan 1, 1965

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-In phase diagram has been determined by thevmal, filtvation, micrographic, and X-ray diffraction methods. This alloy system is characterized by 1) limited solubility of indium (-2 at. pet) in 6 and e plutonium, 2) one eutectic, and 3) fizte intermediate phases. Of the latter, PuIn and PuIn3 melt con-gruently, and Pu31n, Pu31n5, and the high-temperatuve 7 solid solution are formed peritectically. The n phase decomposes eutectoidally into Pu3In and PuIn at 865°C. Although the 6 phase can readily be retained to room temperature, it is not thermo-dynamically stable below 300°C. The Pu-In system has been investigated at Los Alamos as part of a study of the alloys of plutonium with the group 111-B elements. Constitutional studies of the Pu-A1 and Pu-Ga systems have been reported earlier.'9' To date, published information on the constitution of Pu-In alloys covers only the identification of the intermediate phases Pu3In and PuIn3.3,4 EXPERIMENTAL The alloys were prepared from five different lots of plutonium and three different lots of indium. The principal impurities in the plutonium differed from lot to lot within the following limits (in ppm): iron, 30 to 80; nickel, 30 to 60; aluminum, 15 to 30; silicon, 20 to 145: thorium, 50 to 300; carbon, 75 to 335; and oxygen, 20 to 135. Spectroanalysis of the indium showed that two of the lots were 99.9 wt pct pure, and the third was 99.98 wt pct pure. The alloys, in the form of about 5-g buttons, were prepared by arc melting in conventional equipment. The components for each alloy were weighed to the nearest 0.1 mg. In most instances the weight losses during melting were negligible; therefore confirmatory chemical analyses were usually not made. A few results are given in Table I. Density measurements of the arc-cast buttons were made by the liquid displacement of bromoben-zene. Heat treating was done in muffle furnaces controlled to +2°C. The alloy buttons were wrapped in tantalum foil before being enclosed in evacuated clear silica capsules. As a precaution against breakage, each capsule was in turn placed in a silica tube closed with a refractory wool plug prior to being charged into the furnace. For a moderately fast quench of the alloys, the outer protection tubes containing the capsules were plunged into cold water. Differential thermal analyses (DTA) in racuo were performed at heating and cooling rates of about 1.5°C per min. Tantalum crucibles having inverted thermocouple wells were used for most of the analyses. It was found micrographically, however, that the liquid alloys containing more than about 35 at. pct In reacted with the tantalum, resulting in contamination of the surface of the alloy. A search for a more satisfactory crucible material was not successful: tungsten and yttria behaved comparably to tantalum; thoria, vitrified magnesia, and vitrified alumina severely contaminated the alloys. So as to minimize the contamination by the crucible mater-

Jan 1, 1965

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By George W. Leney

The iron ore industry might justifiably claim to have originated the science of geophysical prospecting. Their use of geophysical methods was probably the first application of these scientific techniques to the search for economic materials although the exact origin is undoubtedly lost in the unrecorded observations of. some prospector experimenting with compasses or bits of lodestone. Since 1879 when Thalen published "On the Examination of Iron Ore Deposits by Magnetic Measurements" these methods have been a standard supplement to other prospecting techniques. However, many of the great ore bodies of the Precambrian iron ranges were not particularly suitable for geophysical work. The ores were oxidized and enriched through leaching of silica so that they were nearly non-magnetic and other physical properties which distinguished them from the wall rocks were largely destroyed. With the gradual exhaustion of these high grade direct shipping ores, and ores that could be beneficiated by simple means, the iron ore industry turned initially toward the importation of similar high grade foreign ores. At the same time, new processes for concentrating lower grade materials were being developed and older ones improved upon. These concentrates' when pelletized produced such important savings in blast furnace hot metal costs that they now command a premium in the iron ore market and have weakened the competitive position of the remaining high grade ores. The ore bodies now being sought are usually unoxidized and frequently they are also metamorphosed.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By Glenn L. Cook

Correlations between mass spectra and molecular structures of 186 organic sulfur compounds are discussed. The olefinic ions, the alkyl ions, the CnE2n+1 ions, the m/e 61 ions, and the m/e 35 ions in the spectra of thiols are related to molecular structure. In the spectra of sulfides, the olefinic ions, the m/e 61 ions, the m/e 35 ions, the CnH2n+1S+ ions, and the CnH2n+1SH+ ions are correlated with molecular structure. For disu1fides, the correlations relate HSSF+& and RSSH+ ions to molecular structure. Base peaks of alkylthiophenes are correlated to their molecular structures. Some unimolecular reactions of sulfur compounds in the mass spectrometer are considered. A cyclic intermediate is suggested for the reaction which produces m/e 47, CH3S+, and m/e 48, CH4S+, ions in the spectra of sulfides. An expanded ring is suggested as a possible intermediate in the reactions of thiophenes. Heats of formation of sulfur-containing ions and their appearance potentials are presented in tabular form. Ionization potentials for sulfur-containing radicals and molecules are also given. Discussion of the spectra, tabulated in the appendixes, provides an insight into the relationship of the molecular structure of a compound to the mass-to-charge ratios and the intensities of the ions in its mass spectrum. Correlations of the mass spectra with molecular structures are empirically developed by observing regularities in the spectra of the reference compounds. Correlations extend the usefulness of mass spectra because they can be employed to determine the molecular structure of an unknown compound.

Jan 1, 1965

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965

By F. F. Skiba, J. E. Warren

An idealized miscible displacement process in a three-dimensional, heterogeneous porous medium has been studied via experimental computation based on a "Monte Carlo"' model. The macroscopic dispersion which results solely from variations in the permeability of the porous system is related to the scale of the heterogeneity as well as the distribution function for the permeabilities. The interpretation of laboratory data is often subjective and may bt? misleading since ambiguities are not always recognized. Furthermore, an experiment performed on a conventional oil-field core does not yield a valid measure of Macroscopic dispersion for reservoir engineering purposes since the scale of heterogeneity that is significant in the laboratory is not significant in the reservoir. The analysis of field-performance data is discussed and it is shown that a unique characterization of the reservoir can not be obtained from this information alone. A possible method based on a minimum of data, for estimating the spatial distribution of permeabilities in a reservoir is postulated INTRODUCTION Many studies concerned with diffusion and dispersion in porous media have been undertaken because of the potential importance of miscible displacement processes for increasing the recovery of oil. The results from a large number of these studies have been published; in a recent paper Perkins and Johnstonl presented a comprehensive survey of the pertinent literature and excellent appraisal of the "state of the art". In this investigation, dispersion resulting from macroscopic variations in the properties of the porous medium is of primary interest. Dispersion, in this sense, is caused by fluctuations in the velocities of the individual fluid elements as they move through the porous system. This phenomenon is the result of inhomogeneities in the permeability and/or porosity, but it can be amplified by differences in the characteristics of the fluids involved. The objectives of this study are the following: (1) to determine the qualitative manner in which macroscopic rock properties affect the observed dispersion coefficient; (2) to evaluate the possible influence of macroscopic dispersion on laboratory experiments; and (3) to appraise the significance of macroscopic dispersion with regard to reservoir performance. Investigations of this type are essential since many miscible displacement processes, while seemingly understood from a mechanistic point of view, do not behave in a predictable manner under field conditions. Although a plausible explanation is that the process is dominated by the environment, little serious effort has been devoted either to describing the reservoir itself or to determining the probable effect of the reservoir properties on the process. This study is intended to be exploratory in nature; however, it is hoped that it will provide additional insight into the physical problem and that it will suggest areas suitable for further investigation. EXPERIMENTAL COMPUTATION MODEL To limit the observed dispersion to that which results solely from variations in the properties of the porous medium, an idealized process in which one incompressible fluid displaces another identical fluid is simulated. This simulation is achieved by means of a modified Monte Carlo method — by tracking a number of mathematical particles (tracer) through the system according to the steady-state, single-phase velocity distribution. Then the system is characterized by the distribution of the residence times of the particles. Since any number of particles can be injected simultaneously (a true delta-function distribution) and only pressure conditions are imposed on the boundaries, the model is completely determinate. Furthermore molecular diffusion, microscopic dispersion, adsorption and/or reaction are automatically precluded from the model. The heterogeneous medium is represented by a rectangular, three-dimensional array of uniform, homogeneous porous blocks which are randomly arranged; it is assumed that any two opposing faces of the system are held at fixed potentials

Jan 1, 1965

By H. Biloni

A metallographic study of solute segregation produced during controlled solidification of Sn-Pb alloys has previously been reported.' It was found that the growth conditions which produced well-developed cellular substructures led to severe segregation, and even at solute concentrations of 0.2 wt pct Pb regions of a lead-rich phase were formed at the junctions of cell boundaries (nodes). Similar sample preparation and etching techniques have now been applied to several tin alloys at more dilute concentrations. The crystals were solidified uni-directionally under less-severe growth conditions so that the predominant interface structure was composed of two-dimensional cells.* Binary alloys with lead, using 9.999 pct Sn as a solvent, and ternary alloys with lead and bismuth or lead and antimony, using zone-refined tin as a solvent, were examined. The liquid was decanted from the growing crystals in all cases to reveal the interface structure and ensure that two-dimensional cells were being formed. However, since interference may arise from a liquid layer that clings to the interface during decanting,3 an examination of the segregation pattern was always made behind the interface. In all cases, the structure within the bulk of a crystal at greater than 1 cm behind the decanted interface was substantially the same as that nearer the interface. Representative photomicrographs of the dilute Sn-Pb alloy are shown in Figs. 1, 2, and 3. Most observations are similar to those of the previous investigation. For example, the solute concentration at the cell walls is higher than in the intercellular regions; where cell boundaries meet, the segregation is enhanced; the macromosaic or stria-tion substructure and grain boundaries show enhanced segregation; there is also a depletion of solute at cell walls near a striation boundary, as Spittle et a1.4 have observed at decanted interfaces. Not all these observations can be seen in the photos shown since attention has been focused on a special feature; as evident in the photomicrographs, cer-

Jan 1, 1965

Wire rope, when used for hoisting on a mine is one of the most vulnerable units in the most expensive group of installations on the mine. With the introduction of hoisting on the Koepe sheave, a new technique was established. This innovation brought with it certain advantages which long had been recognized and which are being developed further.A need exists for the development of an infallible non-destructive testing device for wire ropes and it is axiomatic that the development and application of such a device should be coupled with the physical examination of mine hoisting systems. Therefore an integrated type of research programme is necessary in order to correlate the effect of shock loading with rope damage, which may be detected ultimately bynon-destructive means. This paper reviews certain historical aspects of investigations on this topic and it outlines a policy for research which can cope with a.c. or d.c. methods of excitation of the rope.INTRODUCTIONThe importance of wire rope in mining operations is often not fully recognized. A wire rope when used for hoisting in a mine shaft should be regarded as a "machine" forming part of a system of machines, and consequently it should be specified as such when it is purchased, it should be maintained as such during its working life, and it should be discarded only when it has done its duty and has been rendered either unsafe or uneconomic for further use.Every mine shaft, vertical or inclined, has in it one or more wire ropes which are used to transport men, material, and ore. Considering the long history of wire rope haulage and the large number of rope applications, it is a tribute to wire rope makers and to mine maintenance engineers, throughout the world, that not many serious accidents have occurred because of failure of wire rope. However, when a...

Jan 1, 1965

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today's complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can't. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By T. A. El-Bassyouni, Paul Gordon

Grain-gvowth data in zone-refined aluminum and in dilute alloys of copper with this aluminum have been obtained. The amounts of copper added were from 4 to 400 at. ppm. It was found that in both the unalloyed aluminum and the alloys grain growth was characterized by a high value of n in the isothermal growth equation 6n = Kt The inadvertent presence of 1 at. ppm Fe in the alloys was found to he more potent in slowing growth than the purposely added copper. Possible rationalizations of these observations and their general relevance to the theoretical use of gvain-grozvth data have been discussed. Grain growth data of Winegard and his co-workers&apos; on zone-refined tin and dilute tin alloys were analyzed with some success2 in terms of approximate theoretical equations for boundary migration.2-4 In view of this success, experiments were carried out in an effort to obtain similar data on zone-refined aluminum and on dilute copper-in-aluminum alloys. The results obtained were anomalous in several respects and could not be used to test theory. A discussion of these anomalies is presented here; they have been attributed to impurity effects and serve to emphasize the sensitivity of grain growth in general—and the particularly high sensitivity in aluminum—to impurities. The resulting difficulties in the theoretical use of grain-growth data are also discussed. EXPERIMENTAL DETAILS An aluminum bar was zone-refined and leveled by methods similar to those described previously.&apos; The degree of purity obtained is indicated in Table The data in Table I were determined by mass-spectrographic methods through the courtesy of Mr. Thomas A. Johnson of AIAG Metals, Inc.* Three dilute copper alloys with this aluminum were prepared also by methods described previously.&apos; The alloys contained nominally 4, 40, and 400 at. ppm of Cu, respectively (0.001, 0.01, and 0.1 wt pct). Each material was fabricated by swaging and rolling into a round bar about 1/4 in. in diameter with an annealed penultimate grain size of approximately 0.003 to 0.007 cm. In order to minimize preferred orientation the fabrication was carried out in several steps, each consisting of a reduction of about 40 pct followed by a recrystallization anneal. Annealing temperatures for the grain-growth studies were attained by the use of boiling liquids up to 213°C and molten metal baths at higher temperatures. Temperatures were controlled to within 1°C. Samples for measurements were cylinders about 3/4 in. long and 1/4 in. in diameter cut from the fabricated rods. In the interests of sample economy a single sample was used for the grain-growth measurements at each temperature. Each sample was, thus, annealed for several successive periods of time, the grain size being measured at each annealing period on a transverse surface exposed by

Jan 1, 1965