Search Documents

By R. D. Daniels, T. W. Wood

The tensile properties of columbium and Cb-H alloys containing up to 455 ppm H were studied as a function of temperature and strain rate. Hydrogen, introduced into columbium at elevated temperatures, using a thermal -equilibrium technique, embrittled columbium most severely at about —77°C. This elnbrittle ment occurred even at hydrogen concentrations of an order of 20 ppm. At higher temperatures, the hydrogen tolerance of columbium increased in relation to the increased solubility of hydrogen in tile metal. Below this temperature hydrogen tolerance, as determined by ductility and fracture stress, increased slightly. Strain rate had little effect on the tensile results for cross-head speeds over the range 0.002 to 2.0 in. per min. Strain aging during the tensile test appears to explain the ductility mininmum at —77°C. The apparent increase in hydrogen tolerance at lower temperatures is attributed to the low mobility of hyhogen. Experiments were performed in which samples were prestrained in tension at room temperature and tested to failure at —196°C. Results suggest that hydrogetz segregation to preformed crack nuclei can cause subsequent embrittlement even at temperatures where hydrogen mobility is too low to cause embrittlement in a normal tensile test. COLUMBIUM is an example of the class of bcc metals with ductile-brittle transition temperatures sensitive to the presence of interstitial atom contaminants. Hydrogen is one of these embrittling contaminants. The embrittling effect of hydrogen is less potent, perhaps, in columbium than in some of the other bcc refractory metals, but it is still a problem of both theoretical and practical interest. Unlike hydrogen in iron and steels, hydrogen in columbium is exothermically rather than endo-thermically occluded. The embrittlement process in exothermic systems has not been studied as extensively as that in endothermic systems, especially at hydrogen concentrations below the limit of solubility. The purpose of this investigation was to evaluate the embrittlement process in initially pure columbium as a function of hydrogen content, temperature, and strain rate. The Cb-H phase diagram, according to Albrecht et al.,1 is shown in Fig. 1. Columbium reacts exothermically with hydrogen producing a solid solution at concentrations of less than about 250 ppm (parts per million by weight) H at room temperature. At concentrations above the highly temperature-dependent solvus a second phase is formed. Like many similar hydrogen-metal systems,2 his system exhibits a miscibility gap with respect to hydrogen solution. Albrecht found the critical temperature of the miscibility gap to be about 140°C, the critical concentration to be 0.23 atom fraction hydrogen, and the critical pressure to be 0.01 mm Hg. Above 140°C there is a solid solution of increasing lattice constant extending across the phase diagram. Hydrogen concentrations of particular interest in this investigation were those below the limit of solubility in columbium. At hydrogen concentrations above the limit of solubility, columbium will contain the hydrogen-rich second phase and will be brittle under most testing conditions because the hydride generally precipitates as platelets with coincident matrix lattice strains.1'3 At hydrogen concentrations below the limit of solubility, the tensile behavior of columbium is expected to be more sensitive to the interrelationships between hydrogen concentration and mobility and the testing variables such as temperature and strain rate. Literature references to the hydrogen embrittlement of metals, especially ferrous alloys and titanium alloys, are too voluminous to mention. It is only recently, however, that detailed studies of the hydrogen embrittlement of columbium have been undertaken. Wilcox et a1.4 studied the strain rate and temperature dependences of the low-temperature deformation behavior of fine-grained are-melted columbium (1 ppm H) and the effect of hydrogen content (1,9, and 30 ppm H) on the mechanical behavior of columbium at a series of temperatures for a single strain rate. A strain-aging peak was ob-served at about -50°C which was attributed to the presence of hydrogen in the metal. Eustice and carlson5 studied the effect of hydrogen on the ductility of V-Cb alloys at a series of temperatures over the range -196° to 25°C. Pure columbium was embrittled by 20 ppm H which produced a ductility transition at approximately -70°C. Ingram et al.6 studied the effect of oxygen and hydrogen on the tensile properties of columbium and tantalum. A minimum in the notched-to-unnotched tensile ratio of hydrogenated columbium was obtained at about -75°C, but because of the relatively large hydrogen content employed (200 and 390 ppm) the ductility

Jan 1, 1965

By A. J. Hatch

Recent disclosures concerning strengthening of anisotropic sheet materials under biaxial stresses are reviewed. This biaxial strengthening has been termed "texture hardening" by Backofen and is related to the normal anisotropy parameter, R. Measurements of R made on three annealed titanium alloys indicate a Ti-4Al alloy will have the greatest potential for texture hardening, followed in order by Ti-5Al-2.5Sn and Ti-6Al-4V. Relative to sheet texture, a review of the deformation mechanisms in titanium alloys would indicate that a preferred orientation for "texture hardening" is where the (0001) pole is normal to the sheet plane. This was confirmed by determination oj (0001) pole figures for the above three alloys. High R values are related to pole figures with (0001) normal to the sheet plane, whereas low R values are related to pole figures with (0001) split in the transverse direction from the sheet normal. PUBLISHED work by Backofen et al. 1 and Hosford and Backofen2 based on hill's' mathematical theory of yielding in anisotropic metals has indicated that significant strength advantages under biaxial stresses are possible in hcp alloys, provided an ideal (0001) [1010] sheet texture exists. This tendency to strengthen under biaxial stresses has been termed "texture hardening".1 It can be quantita- tively characterized by a strain-ratio parameter, R, where R may be determined from the ratio of natural width strain to natural thickness strain as measured on a uniaxial test specimen cut parallel to the rolling direction. If R is greater than 1.0, then strengthening under biaxial tension would be predicted. Considering the a titanium alloys which have an hcp crystal structure, Williams and Eppelsheimer4 have reported that commercial-purity grades deviate from the ideal (0001) sheet texture mainly in an approximate 30-deg rotation of the basal plane, toward the transverse sheet direction. However, McHargue et a1.5 have shown that the angle of rotation of the basal plane is sensitive to alloy content. In particular, a titanium alloy with 3.8 pct Al was reported to have the ideal (0001) [1010] texture after cold rolling. Additionally, Backofen et a1.1 using plane-strain compression tests have reported R values greater than 5.0 for the commercial 0 alloy Ti-5A1-2.Sn (110-AT). In view of these findings, a program was initiated to further determine the potential of commercial Ti-5A1-2.5Sn and an experimental Ti-4A1 alloy with respect to "texture hardening". Also, because of its wide commercial use, Ti-6A1-4V was included in the investigation. BIAXIAL-STRESS THEORY FOR ANISOTROPIC MATERIALS Backofen ef al.,1 based on the mathematical theory of Hi11,3 has introduced the concept of "texture hardening". In this work, it was shown that possi-

Jan 1, 1965

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965

By George C. Fryburg

The oxidation of platinum at high temperatures (above 800°C) is controlled by boundary-layer diffusion, except at the lowest pressures. The rate of oxidation is determined by the rate of diffusion of oxide through the boundary layer away from the platinum. This is in contrast to the situation in tungsten and molybdenum oxidation, where the rate is controlled largely by the diffusion of oxygen through the boundary layer towards the metal. The difference in mechanism is a consequence of the much lower rate of oxidation of platinum. Evidence is presented that supports this mechanism for the oxidation of platinum. SOME years ago we reported1 a study of the oxidation of platinum in ordinary oxygen in the temperature region above 800°C, where the oxide is volatile. All the data available up to that time had been obtained with platinum crucibles or plates heated in tube furnaces. The results were widely variant and highly dependent on the flow rate of gas through the furnace: the faster the gas flow rate, the higher the measured oxidation rate. These results indicated to us2 that reaction equilibrium was being approached in the furnace and that the rate was diffusion limited. To minimize these effects, we employed1 electrically heated ribbons placed in a cooled bulb. We were primarily interested in the low-pressure region, but some experiments were performed at pressures up to 1 atm. We found a peculiar pressure dependency which was explained on the basis that the rate of oxidation was proportional to the pressure at all pressures, but that with increasing pressure an increasing fraction of the volatilizing oxide was back-reflected to the ribbon by the surrounding gas molecules. The oxide molecules are not stable at the temperature of the platinum and are decomposed on impact, the platinum being re-deposited on the specimen. Because of the limitations of space, this explanation was offered summarily without detailed support. Recently, Jaffee and associates3, 4 have suggested that the pressure dependency of our data up to 0.5 torr could be explained on the basis of a Langmuir-type adsorption of molecular oxygen followed by dissociation. Since the correct explanation of the effect of pressure on the oxidation rate is a necessary requirement to the development of the basic mechanism of the oxidation reaction, we felt that the back-reflection theory should be presented in more detail. This is the object of the present paper. RESULTS AND DISCUSSION A typical set of results showing the pressure dependency of the oxidation reaction is presented in Fig. 1, where we have plotted, on logarithmic scales, the rate of oxidation, R, vs the pressure, p. For comparison some results of Krier and Jaffee4 and of Raub and plate5 are also shown. These data were taken at atmospheric pressure using furnaces. The effect of reaction equilibrium within the furnace is apparent from the much smaller values that these observers obtained: Raub and Plate In O2 found a rate of 3.1 µg cm-2 hr-1 compared to our value of

Jan 1, 1965

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

By D J. Murray

This paper outlines the principles of friction hoisting and the components involved, and gives a description of a specific mine hoist. Friction hoisting is compared with conventional drum hoisting, and the depth of shaft at which friction hoists become more economical than drum hoists, with respect to power consumption, is determined. Introduction T HE purpose of this paper is to outline the principles of friction hoisting, to describe the components and to show the advantages of multi-rope friction hoisting. Some calculations are made to show that the power requirements and the initial costs of friction hoists are less than those of conventional drum hoists, once a certain depth of shaft has been reached. The use of multi-rope friction hoists is gradually superseding the employment of the conventional drum hoist in many parts of the world. It results in heavier payloads from deeper levels, an increase in shaft safe-ty and a more compact installation for protection against adverse weather conditions. It was observed that where drums and friction sheaves exceeded 30 feet in diameter, a number of mechanical disadvantages were being experienced;

Jan 1, 1965

By L. H. Adami

The heats of formation of anhydrous cadmium sulfate, cobalt sulfate, copper sulfate, nickel sulfate, and zinc sulfate were determined by hydrochloric acid solution calorimetry. The values at 298.15° K for formation from the metal, rhombic sulfur, and oxygen gas follow (cal/mole): CdS04J -222.0 ± 0.3; CoS04, -212.0 ± 0.4; CuS04) -183.4 ± 0.6; NiS04, -208.1 ± 0.2; and ZnS04, -233.1 ± 0.2. Corresponding heats of decomposition to form the metal oxide, sulfur dioxide, and oxygen were derived from these results; heats of decomposition to form the metal oxide and sulfur trioxide were also derived.

Jan 1, 1965

By W G. Forbes

SOME 20 years ago, upon finishing second year at the University of Manitoba, I was faced with the choice of whether I wanted to be a geologist or a chemist. Accordingly, I sought out Professor Brownell, Head of the Department of Geology, to ask him what a geologist did. His reply contained the statement that following graduation one went out into the field in northern Canada for 5 to 15 years to reduce to practice what had been learned at university. To a young man, very socially conscious, even one year, let alone 5 to 10, in a small mining community sounded like being banished to a monastery in the Himalayas and thus I turned to chemistry. Moving to the present, last month I asked a geologist, and then a mining engineer, what does the fresh graduate in their field do these days? The reply was: usually serve an apprenticeship for an indeterminate period either underground or in the field learning the job.

Jan 1, 1965

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By A. S. Michaels, M. C. Porter, A. Stancell

Previous laboratory studies have demonstrated that the injection of small quantities of reverse wetting agents during water displacement can increase oil recovery from unconsolidated porous media.9 In the present investigation, an attempt has been made to determine more fully the effects of reverse wetting treatments and to clarify the mechanism by which increased oil recovery is effected. Water-oil displacements were performed in beds of 140-200 mesh silica sand. Hexylamine slugs (injected after 0.25 pore volume of water throughput), when adequate in size and concentration, were effective in promoting additional oil recovery. Their effectiveness increased with the quantity of amine injected. However, slugs of sufficient size and concentration to stimulate oil production at water flow rates of 34 ft/day did not do so at 4 ft/day. Visual studies in a glass grid micromodel have shown that the stimulation of oil production, via ayueous hexylamine, is a result of transient changes in the oil wettability of the pore walls. if the amine slug is of sufficient size and concentration to induce significant changes in the adhesion-tension, large continuous oil masses will be formed. if the superficial water velocity is high enough to result in rapid desorption of the amine, a favorable "wettobility gradient" may be established across the masses; under such conditions, high oil mobility is observed, and increased oil recovery results. INTRODUCTION It is generally agreed that the efficiency of oil displacement by water in porous media is limited in part by capillary forces which cause the retention of isolated masses of oil — resulting in the so-called "irreducible minimum oil saturation". Recent estimates10 indicate that there are about 220 billion bbl of petroleum in United States reservoirs which are not economically recoverable with present techniques (such as water flooding). This amounts to almost five times the known recoverable reserves. It has been recognized for some time that a suitable alteration in the water-oil interfacial tension and/or the contact angle, as measured between the water-oil interface and the solid surface, should result in better displacement efficiency. Surface active agents can be used as interfacial tension depressants to accomplish this objective,1,2,7 but unfortunately, the additional oil recovery is seldom commensurate with the treatment cost. In contrast to interfacial tension depressants, the effect of contact angle alterations on water-oil displacements has received relatively little attention in the literature. It is known that the wettability affects the displacement process.3,4,11 Displacements in water-wet systems generally result in lower residual oil saturations than those in oil-wet systems. The effect of "'transient" wettability alterations concurrent with the displacement process have been investigated by Wagner, Leach and coworkers,4,11 wherein it has been demonstrated that the establishment of water-wet conditions during water flooding of oil-wet, oil-saturated porous media is accompanied by significant increase in oil displacement efficiency. Michaels and Timminss studied the effects of transient contact angle alterations resulting from chromatographic transport of reverse wetting agents through unconsolidated sand. It was demonstrated that chromatographic transport of short-chain (C4 through C8) primary aliphatic amines can improve oil recovery and that the recovery increases with the quantity of amine injected (i.e., with either the amine concentration or the volume of the slug injected). Circumstantial evidence indicated that the increased displacement efficiency resulted primarily from transient changes in wettability of the porous medium. In the Present investigation. additional information has been obtained on the effects of reverse wetting treatments and the mechanism by which increased oil recovery is accomplished. Hexylamine slugs of varying size and concentration were chromato-

Jan 1, 1965

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ' constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965

Jan 1, 1965

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling' rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y' depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, ''' the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y' phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,'' but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By H. Conrad, K. Janowski, E. Stofel

In a previous paper,1 the occurrence of (0001) and (0111) twins was reported for compression tests of 60-deg-oriented sapphire rods in the temperature range from 1100° to 1300° C. Subsequent to this initial work, additional tests have been conducted, and twinning has been found to occur at temperatures as high as 1500° C. Also, the temperature and strain-rate conditions for the two types of twins and for slip have been established in more detail. The present note covers this more recent work. The compression-test data are summarized in Table I. The techniques for identifying the twins are optical examination up to X1000 and X-ray analysis.' It is evident that (0711) twins are pre-

Jan 1, 1965