Search Documents

By F. Paredes, W. R. Holman, R. W. Crawford

The diffusion coefficient for hydrogen in the ß titanium alloy containing 13 pct V, 11 pct CY, and 3 pct A1 was measured over the temperature range 20° to 500°C. Results fit the expression: D= 1.58 x lgs exp-------==-----) cm2,sec THE diffusion coefficient for hydrogen in the metastable ß-phase titanium alloy containing 13 pct V, 11 pct Cr, and 3 pct A1 was measured as part of an investigation of the effects of hydrogen on the mechanical properties of titanium alloys. Several theories on the mechanisms of hydrogen embrittle-ment include diffusion of hydrogen at ambient temperature as an important step in the embrittling process.'-5 In hydrogen-contaminated a-ß titanium alloys, it has been postulated that the rate-controlling step may be the rate at which hydrogen diffuses from the ß phase to stress- or strain-nucleated brittle hydride platelets at the a-ß interface.' However, embrittlement of the all-ß alloy investigated in this work may proceed by a different mechanism, since this alloy can be embrittled without the formation of detectable hydride platelets.6 Troiano has suggested that in this case the mechanism of delayed failure or embrittlement is similar to that proposed for high-strength steel, i.e., repeated crack initiation caused by a decrease in bonding energy as hydrogen diffuses to points of high tri-axial stress at the root of a notch. In both types of alloy the rate of embrittlement is believed to be controlled by diffusion of hydrogen in the ß phase. Accurate hydrogen-diffusion data in the vicinity of room temperature should therefore be of some assistance in understanding the mechanisms of embrittlement in these two classes of titanium alloys. Diffusion of hydrogen in pure titanium has been studied by Wasilewski and Kehl7 at temperatures above 500°C. Their measurements on diffusion in the ß phase were extended below the ß-a transformation temperature (882°C) to approximately 600°C. This was possible because of the 8 stabilizing effect of hydrogen. No results at lower temperatures have been published and there are no data in the literature on hydrogen diffusion in the ß -phase alloy used in this program. Hydrogen diffusion in metals is generally investigated by measuring the rate of transport of hydrogen past a solid-gas interface, i.e., by absorption, permeation, or degassing-rate measurements. These methods produce accurate diffusion data when bulk diffusion is the rate-determining step in the over-all process. However, at the lower temperatures of interest in hydrogen-embrittlement studies or under conditions where surface films are present, the measured rates may be surface-controlled and the calculated diffusion coefficients will be in error. Surface effects were eliminated in the present work by using a modification of the common welded-couple technique m which two bars with uniform but different compositions are joined before the diffusion anneal." The same type of step change in the initial concentration vs distance curve was produced by electrolytically hydrogenating thin-strip specimens which had been electrically insulated over half of their length. Concentration vs distance curves were determined, after appropriate diffusion-annealing treatments, by vacuum-extraction analyses of transverse samples sheared from the strips. Diffusion coefficients were calculated by the methods of Grube.M This technique was feasible because of the large concentrations of hydrogen which can be charged into p -phase alloys without the formation of hydrides15'16 and because of the extremely low degassing rates observed when hydrogenated titanium alloys are heated in air. EXPERIMENTAL WORK The diffusion couples were cut from a 0.022-in.-thick mi ll-annealed sheet.* Strips 8 in. long by 1/2

Jan 1, 1965

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By Jerry W. Ramsey

The Bureau of Mines examined a low-, a medium-, and a high-volatile Pennsylvania anthracite by densimetric methods using four mesh si.s of each anthracite. Using high-pressure mercury the macropore volumes and distributions of these pore volumes determined, densities in mercury were calculated, and specific pore vo1.r. ware obtained from these mercury densities in conjunction with helium densities. The helium densities were also used with the ultimate analyses of these anthracites in calculating structural parameters by statistical densimetric methods. The effect of 106 or 108 rads of gamma irradiation in the presence of air and in vacuum upon the properties studied with two mesh sizes of each anthracite. Results of the statistical densimetric method seem to show some breakdown of condensed ring structural units at the lower irradiation level, with subsequent polymerization at the longer period of gamma irradiation. The structural parameters obtained also indicated that in going from high- to low-volatile anthracite, either the number of condensed rings per structural unit increased, or the degree of polymerization increased.

Jan 1, 1965

By Hsun Hu, R. S. Cline

The formation of annealing textures during the course of recrystallization in 2 pct Al-Fe crystals rolled in the (111) [112], (112) [111], and (112) [Till orientations has hem studied in detail. When the rolling texture is composed of both (111) [121] and (001)[110] components, the annealing texture consists of mainly (110) [001] and (113) [332] components. As the (001) [110] component diminishes from the surface to the interior of the rolled crystal, the relative concentration of the (113) [332] component in the annealing texture decreases accordingly, whereas that of the (110)[001] component increases with the (111)[112] component in the rolling texture. Such dependence of the annealing texture on the composition of the rolling texture is in accmdance with the oriented growth mechanism. Grain-growth characteristics during recrystallization, hence the annealing texture, can he considerablv different in (112) [111]-type crystals depending sensitively on the initial orientation of the crystal. In a previous publication,' the formation of rolling textures in 2 pct A1-Fe single crystals with initial orientations of approximately (1ll)[112], (112)[111], and (112)[111] was studied in detail. The deformation texture of these crystals consisted of either a single (111)[112] or a combination of (111)[112] and (001)[110] components in various concentrations. For the (lll)[112] crystal, the deformation texture was a single (lll)[112] up to 70 pct rolling reduction, but it became (lll)[112] plus (001)[110] after -90 pct reduction. For the (112)[113.]-type crystals, the relative concentration of the (111)[ 112] and (001)[110] components varied with the depth below the surface of the crystal, as well as with the amount of deformation. These series of specimens, having deformation textures with a range of concentration of the (111)[112] and (001)[110] components, could therefore be used for a thorough investigation of the effect of deformation-texture components on the formation of annealing textures. In a study of rolling and annealing textures in Si-Fe crystals, Dunn and Koh3 noted that the addition of a (001)[110] component to the (111)[112]-type deformation texture had practically no effect on the recrystallization texture.* According to the ori- ented growth mechanism for the formation of annealing textures, nuclei related to the deformation texture by approximately 30-deg rotation around a common [110] axis have the highest rate of growth and the resulting annealing textures generally have such an orientation relationship with respect to the deformation textures.314 It was reasoned by Dunn and Koh3 that if the oriented growth mechanism operated the recrystallization texture developed from a deformation texture containing both (111)[112] and (001)[110] components should be strongly centered around (113)[332], because (113)[332] is approximately midway between the (111)[112] and (001)[110], and is related to both of these two orientations by [110] rotations of 25 to 30 deg. Hence, nuclei of (113)[332] orientation should have a high rate of growth in the deformed matrix. However, their results were not in accord with this prediction. It was felt by the writers that a detailed study was needed to clarify the effect of deformation-texture components on annealing-texture formation. For this reason, the present investigation was conducted. EXPERIMENTAL PROCEDURE Specimens used for the present investigation were taken from the crystals rolled previously for deformation-texture studies.' In order to follow the progress of annealing-texture formation during the course of recrystallization, a single specimen was taken from each rolled crystal and its textural changes examined after successive anneals until recrystallization was complete. The specimen was carefully cut from the rolled strip with a jeweler's saw. Prior to annealing, the sawed edges were etched to remove distorted metal, while both faces of the specimen were protected from the etching solution by acid-proof plastic tape. After annealing, the specimen was etched from the "bottom" face only (the reference or "top" face of the specimen was protected by plastic tape) to one half of its original thickness, so that the texture at the surface and at the central section of the strip could be determined by the reflection technique. The

Jan 1, 1965

By Alan English

This paper reviews the process control systems used in early commercial pelletizing plants, traces the development of these systems into present day practice, and briefly outlines advanced automation concepts being considered for future installations. It deals specifically with controls for the balling circuit, pelletizing machines, and related material handling and combustion equipment. The importance of instruments for visual observation and data logging is discussed, and the potential use of computer control is evaluated.

Jan 1, 1965

By I. R. Kramer

The stress associated with the high-dislocation layer at the surface of deformed aluminum crystals was measured by progressively polishing the specimen and determining the change in the initial flow stress when the specimen was reloaded. This surface stress increased linearly with strain in the Stage II and Stage III region. The depth to which the high-dislocation layer extends was found to be 0.0025 in. The influence of the surface layer on Stage I is discussed and it is shown that Stage I ends when, on the secondary slip system, the difference between the applied stress and the opposing stress due to the surface layer is equal to the critical resolved shear stress. In previous papers'-3 it was shown that the surface exerts a pronounced effect on the plastic-flow characteristics of metals. For fcc metals it was possible to increase the extent and decrease the slope of Stages I and II and decrease the work-hardening coefficient of Stage II by removing the surface of the specimen continuously during the deformation process.2,3 More recently,L it was shown that the activation energy for plastic deformation and the activated volume were also influenced by the surface. These changes were related to the existence of a high concentration of dislocations in the region near the surface of the deformed specimen and it was concluded' that the effective stress, T, acting on a dislocation was T = Ta-Ti-Ts [1] where 7, is the applied shear stress, Tj is the internal stress, and TS is the stress associated with the surface region containing the high concentration of dislocations. From Eq. [I] it is seen that the effective stress, 7, acting on a dislocation is a function of 7,. Therefore 7, becomes important in any description of the work-hardened state. In this paper the value of 7, as a function of strain and its variation with depth are reported for aluminum single crystals. In particular, it will be shown that the end of Stage I occurs when the net stress, 7, on the secondary slip system is equal to the critical resolved shear stress. To measure Ts, single crystals of aluminum were deformed in tension to various strains, whereupon the load was removed and a known amount of metal was removed by electrolytic polishing. The differ- ence between the final flow stress before the specimen was unloaded and the initial flow stress upon reloading is designated as ?Tp and is the decrease in the stress due to the removal of the surface layer in whole or in part. The value for Tp is taken equal to -Ts. EXPERIMENT PROCEDURE The details of the tensile apparatus, method of electrolytic polishing, and crystal preparation were the same as those used previously,1"3 The single crystals were 1/8 by 1/8 in. in cross section with a 3-in. gage length. The initial purity of the aluminum was 99.997 pet. The specimens were held in vacuo at temperatures 50°C below their melting points for 16 hr and furnace-cooled. Just prior to the application of the tensile stress the specimens were electrolytically polished to remove 0.004 in. from the thickness. This latter operation was conducted after the specimen was placed in the tensile apparatus. The tensile tests were conducted at a strain rate, i, of 10"5 sec-' and a temperature of 3°C. The aluminum crystals used for the determination of 7, are designated A1-3-12 and A1-116. The orientation of the various crystals used throughout the investigation is shown in Fig. 1. The ?Tp values for specimens A1-3-12 as a function of Ax were determined mainly at four strain levels, i.e., ? = 0.0217, 0.0381, 0.0593, and 0.075, where Ax is one half of the total reduction of the thickness after polishing and ? is the re-

Jan 1, 1965

By John I. Sharpe

Masses of pyritic copper and zinc ores are entrapped along the contact zone between two volcanic groups in the Matagami area. The upper limits of the sulphide concentrations tend to form concordant contacts against lava or cherty tuffite units of the younger group; the lower extremities tend to either follow transverse structures or merge with zones of dispersed sulphides. The sulphides are deformed and intruded by folded dykes. Close relations between metallization boundaries and volcanic lithology and stratigraphy, and a preliminary investigation of the fabrics and crystallization temperatures of the sulphide masses, suggest that the copper and zinc (but; not necessarily all the iron sulphides) were emplaced at h1gh temperatures during volcanism in near-surface lithological-stratigraphic traps. Introduction T HE Matagami area is centered 120 miles north of the Val d'Or and Noranda camps in north-western Quebec. For the present purpose, it is considered to comprise a 155-square-mile area in Isle-Dieu, Galinee and Daniel townships which encompasses the main sulphide masses. Airborne geophysical surveys within this area in 1956 led to the discovery of a large sulphide body -the.

Jan 1, 1965

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19' sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler's saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By N. Albon, J. F. Miller, R. W. Coutant

The deposition of nickel from nickel carbonyl onto amorphous substrates has been studied, with attention being paid to the specific effects of the physical and chemical nature of the substrate and to the effect of oxygen on the crystal morphology. With substrates having microscratches or etch lines, nu-cleation was observed to occur preferentially at these surface features. Flame polishing of the substrate surfaces was found to remove any regularity in preferred nucleation sites. Nucleation was observed to occur less readily on substrates having relatively low surface energies, e.g., Teflon and carbon, than on materials having relatively high surface energies such as fused silica. At low oxygen concentrations [Ni(CO)4/O2 > 54 x 1031, apparently pure and well-formed nickel crystals were observed to nucleate and grow irrespective of the presence of oxygen. At higher concentrations of oxygen, a secondary growth process, dependent upon oxygen concentration and resulting in a gradual change in crystal morphology, was observed. It is concluded that the influence of oxygen on the nucleation and growth of nickel is determined by the relative kinetics of the various possible reactions, and that under the experimental conditions employed the 0-Ni interaction occurs at some nucleation or prenuclea-tion stage. THE purpose of the research on crystal nucleation in chemical vapor deposition as described in this paper has been twofold: 1) to examine some effects arising from the use of amorphous substrates, and 2) to study the specific effects of oxygen on the nucleation and growth of nickel in a nickel carbonyl-carbon monoxide system. The nickel-nickel carbonyl system was chosen for study for several reasons: 1) nickel films are of potential interest in electronic technology, and 2) the deposition can be carried out at moderate temperatures, thus making possible detailed study of the processes occurring and the use of a variety of substrate materials (including some which melt at relatively low temperatures). Fairly well-characterized chemical kinetics and a broad background of information are available on the py-rolysis reactions and on the mechanisms of Ni-O interactions. NUCLEATION AND GROWTH THEORY The theoretical background for the analysis of nucleation and growth by vapor deposition for a one-component system (physical vapor deposition) and the problems encountered therein have been reviewed by Hirth and pound.' More recently Mande12 has indicated the difficulties of applying such theory to chemical systems. One of the major problems involved is the possible multiplicity of chemical reactions and deposition routes. For example, those reactions which are probably of significance in a discussion of the pyrolytic deposition of nickel from nickel carbonyl under the conditions of the present experimental work are illustrated in Fig. 1. As is true with most cases of chemical deposition, many of the quantitative data necessary for a complete analysis of the system are either not available or not directly measurable. However, with the present system, sufficient data are available for a discussion of nucleation and growth on a qualitative basis. Classically, the rate of nucleation of a monatomic species being deposited from a vapor phase is given by

Jan 1, 1965

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

Jan 1, 1965