Search Documents

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. The history of the drilling of Pilot Hole "XI' is presented. This historical summary provides the details of method used during the drilling of this hole. Problems encountered during drilling are discussed. The quantities of drilling mud and other materials used to drill the hole are documented.

Jan 1, 1977

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By Amitava Ghosh

A new analytical formula for predicting ground vibrations induced by blasting is proposed. One factor accounts for geometrical spreading. One factor corresponds to inelastic attenuation. The geometrical spreading function is based on likely source geometries, idealized as either square-root, cube-root or site-specific scaling, and on the propagation characteristics of predominant wave types. The inelastic attenuation is approximated by an exponential function. The empirical constants in these functions are backcalculated from field measurements. Regression analysis has been performed on twenty-three sets of measured data in order to determine the validity and the effectiveness of the proposed method. In many cases, the proposed method gives better correlation than the conventional method. In most of the remaining cases, there was no difference between the two methods. Best-fit lines given by the proposed method fit the data trend very well, especially at large scaled distances. At large distances the proposed method gives a prediction much closer to the actual values than the conventional methods. The statistical analysis shows not much difference between square-root, cube-root or site-specific scalings.

Jan 1, 1983

By Louis Schaffer

A literature review concerning dredging hazards and dredge safety practices and an examination of MSHA accident and injury statistics on dredge mining in the United States provided the background for an analysis which was completed by visiting 31 dredge operations, dredge manufacturers, and dredging experts. The principal hazards are discussed and countermeasures are suggested in several areas. Drowning is the single largest fatal injury category. Special emphasis is given to the design, care and use requirements of personal flotation devices.

Jan 1, 1984

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Edgar S. Rush

This study was conducted to make a limited evaluation of experimental and standard tractor dozer blades. A field test program was conducted in the southeastern part of Kansas on strip-mined areas where the spoil banks are parallel with rest-to-crest distances between 90 and 120 ft and maximum dozing distances usually less than 50 ft. This evaluation was a part of an overall joint Pittsburg and Midway Mining Company--U. S. Bureau of Mines (USBM) Specialized Reclamation Field Test Program primarily centered on the field t sting of experimental high-volume lateral relocation blades. The three blades evaluated were the 60-ft-wide angle (A) blade mounted on two 41B tractors. a 48-ft-wide A blade mounted on two D9H tractors, and a 13-ft-wide reclamation universal (Rec U) blade mounted on a D9H tractor. In addition to the experimental blades, three commercially available blades were tested: A 20-ft universal (U) blade mounted on two side-by-side (SxS) D9H tractors; a 20-ft U blade mounted on a 418 tractor; and a l2-ft straight (S) blade mounted on a D8H tractor. The dozer blade evaluations compared measured blade performance with soil and other site characteristics and with estimated earth-moving performance rates based on earthmoving methodology that accounts for the traction and speed of the tractor. The earthmoving methodology was also validated with data collected during this program.

Jan 1, 1978

By Glenn Adkins

This report characterizes pivoting joints in the structures of mining machinery and how the wear on the various components, i.e., pins, lugs, yokes and bushings, may affect the safety of mine personnel where these components are allowed to wear excessively before repair or replacement.

Jan 1, 1979

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982