Search Documents

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1974 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Jan C. Still

The Glacier Bay subarea is that part of the Juneau Mining District (JMD) within Glacier Bay National Park and Preserve (GBNP). It is the western portion of the JMD and consists of the land between the Fairweather Range crest and the Takhinsha and Chilkat Ranges crests (excluding that land east of Excursion Inlet.) Figure B-1 shows the area. It is bounded on the north by the Alaska-British Columbia International boundary, to the south by Cross Sound and Icy Strait, and contains Glacier Bay. During 1975 -1977 the Bureau conducted a detailed study of the occurrences, prospects, and deposits in GBNP (B_4).2 This work was in cooperation with the U.S. Geological Survey (USGS) under the provisions of the Wilderness Act (Public Law 88-577). As a follow up to this earlier Bureau work, limited studies were conducted, during 1985 and 1986, as part of the JMD study. This report covers the most important aspects of the earlier studies and the 1985 and 1986 studies. ACCESS The Glacier Bay area may be reached through Gustavus airport, a paved strip which is serviced by scheduled jet airliners in the summer and air taxi services year-round. The airport is connected to Bartlett Cove (GBNP headquarters) by an all-weather road. No other roads exist in the area except a skid road to the LeRoy Mine and mill in the Reid Inlet area. Much of the Glacier Bay area is accessible through the salt water inlets and fjords which are part of Glacier Bay. Cruise ships, charter boats, and fishing boats visit these inlets and fjords during the summer months. Elevations within the area range from sea level to over 15,000 feet in the rugged Fairweather Mountain Range. More remote areas are accessible by small boat, foot, or helicopter. Glacier ice is a year-round hazard to navigation in Glacier Bay, and during the winter months some of the more northerly inlets are frozen.

Jan 1, 2012

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice-chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor. Candace Trimble, member SME, of Oil-Dri Corporation of America, is chair of the Industrial Minerals and Aggregates Division?s Technical Committee.

Jan 1, 2012

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Victor Romero, Steve Redmond

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2011

By A P. Wibowo

Indonesia holds a significant role in the utilisation of coal resources in the world. Although the number of Indonesian coal resources and reserves do not fall into the world’s top ten, according to 2009 statistics, Indonesia is the seventh largest producer of coal with a production of 256 Mt. More than 80 per cent of this amount is sold in the export market, making Indonesia the world’s second largest coal exporter. Most of the exported coal from Indonesia is used to fulfil the needs of the Pacific market, such as Japan, Taiwan, China, among others. It is also possible to reach the Atlantic market.Along with Indonesia’s development program, until 2025 the Indonesian government has adopted a National Energy Policy that aims to reduce the role of petroleum in electricity generation and replacing it with coal. As a follow-up of the policy, since 2009 PT PLN, the state electricity company has built steam power plants throughout Indonesia as an implementation of the first stage of the Electrical Acceleration Project with a capacity of 10 000 MW. Moving forward, in 2011 PT PLN will also build the second stage of the project with a capacity of 10 000 MW. As a result of the program, the domestic need for coal is expected to increase as much as 44.8 Mt.With the increase in domestic need and decrease in the number of reserves, the Indonesian government has adopted policies to secure the domestic coal supply. A policy that may potentially be adopted by the government is the limiting of coal production, seeing the high rate of increase in Indonesian coal production. The adoption of such a policy will change the distribution map of coal in the Pacific market. Thus, this paper will evaluate the change of coal distribution patterns in the Pacific market along with the increase in Indonesian domestic needs and Indonesian adoption of policies regarding the securing of coal supplies.

Nov 22, 2011

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011

By O S. Maluleke

In some deposits valuable heavy mineral quality is poor due to increased mineral surface coatings from higher slimes and more competent sand orebodies. Mineral surface coating can include silica or aluminium rich clay minerals and iron based minerals that render the final product quality off-specification, in this case specifically ilmenite and zircon. Conventional physical beneficiation processes such as magnetic separation, electrostatic separation and gravity separation are not able to remove these surface coatings. Surface dependent separation techniques such as electrostatic separators are affected by these coatings which hinders the rejection of non-valuable mineral from product. Attrition scrubbing is the most commonly used technique to reduce surface coatings, using mechanically induced particle to particle interaction, abrasion and shearing.In many cases it is a challenge to measure the surface removal efficiency of these scrubbing units. Elemental analysis techniques (ie X-ray flourescence) (XRF) in a multi mineral environment are unable to measure surface impurity reduction with enough precision. Mineralogical analysis (in this case Qemscan®) has constraints in terms of sample preparation with highly coated particles being plucked out during block polishing. This paper suggests a combination of laboratory separation techniques coupled with elemental analysis to evaluate the surface removal efficiency. Three different types of feed materials were used to analyse the efficiency of surface removal using production attritioner scrubbers. This approach relates the downstream beneficiation plant’s expected performance with that of the attrition scrubber’s scrubbing efficiency.

Oct 5, 2011

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011

By M J. Pejovic, S BoÜevski, I Miljanovic, M Hudej, A Milutinovic, A Petrovski

The paper deals with the problem of managing the supplies of consumables (energy resources, lubricants, explosives, explosive supplies, tires, spare parts, etc) in mines. After the introductory remarks and comments, a general stochastic model of supply, relating in general to the dynamic programming method is presented. A selection of stochastic supply model for experiments and research by the authors of this paper is not a coincidence, based on of their long experience, showing that this type of model is the most suitable to provide support for decision-making and management of supplies of consumables in mines.In order for the problem?of?consumables?supply?management to be reviewed, in whole and objectively from the aspect of risk, experimental tests of the stochastic model in real conditions were performed at the limestone open pit mine æZelenikovecÆ near Skopje, the capital of Macedonia. The scope of the experimental research enabled reliable analysis. The results obtained confirm the efficiency and reliability of the stochastic model and two separate manipulative-operational positions regarding its application, which may have an important influence on the optimisation of supplies.

Sep 26, 2011