Search Documents

By Robert E. Wallhagen

This report describes the results of a four year investigation into improved face ventilation systems for underground coal mines. The objective was to experimentally determine configurations for a diffuser fan system and a water spray (spray fan) system which will provide a maximum reduction in face methane concentrations without causing an increase in methane concentrations at the operator's position. The experimental evaluation was performed in full scale mock-up mine entries, simulating continuous mining operations in both a six foot and four foot coal seam complete with normal ventilation, water sprays, and methane emission. A limited study was also performed to assess the effect of scrubber discharge location on methane concentrations in the face area. The results indicated that diffuser fan and spray fan systems that were designed to augment the natural airflow pattern in the entry could provide a factor of 3 to 5 reduction in average methane concentration at the face, compared to a mining machine with just conventional water sprays. The properly designed diffuser and spray fan systems also significantly reduced the total methane present in the entry. A properly designed dust scrubber discharge can reduce face methane levels by a factor of two.

Jan 1, 1977

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes' diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer's specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By Robert L. Frantz

This report is a part of the project "Study of the Human Factors Aspects of an Automated Continuous Mining Section". The report covers three phases: Phase I Assessment of the Impact of the Automation Technology on Mining Health and Safety. Phase II Estimation of the Cost-Effectiveness and Productivity of Automation. Phase III Prediction of the Psychological and Organizational Impacts of Automated Mining, The investigation determines that the automation of a continuous mining section will improve the health and safety of the miner, increase productivity and decrease mining costs, result in a more attractive and desirable working environment, and result in a greater rate of return on capital investment.

Jan 1, 1977

Domestic Production and Use: In 1976, 12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 63% of production capacity. Washington, Oregon, and Montana accounted for 36% of the total production; Gulf Coast States 19%, Northern States 29%, and other Southern States 16%. Based on published producer prices output of primary metal in 1976 was valued at $3.8 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1976 building accounted for about 25%; packaging 22%; transportation 19%; electrical 13%; , consumer durables 8%; and other uses, 13%.

Jan 1, 1977

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

By G. F. Kuncir

The analysis described herein evaluates the Bureau of Mines Program for Advancing Mining Technology - Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By G. F. Kuncir

This volume was prepared in support of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation under a Bureau of Mines contract. The evaluation is described in part within a companion volume entitled Benefit-Cost Analysis. The economic mine models outlined herein provide a quantitative basis for the assessment of program benefits. Reference is made to estimated oil shale mine costs to delineate the beneficial impacts that can be expected to accrue for the future implementation of program developed technology. Estimated mine cost data are provided for surface, underground, and modified in situ oil shale mining operations.

Jan 1, 1977

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By H. M. Coggin

The study summarizes the state of the art in rock mechanics, open pit and underground mining, leaching, geology, metallurgy and financial analysis Conceptual design of pit slope caving technique and analyses explore concepts for the exploitation of ore grade remnants in the walls and bottoms of open pit mines and the potential economics of the adaptations Several coded sites were examined for future studies where the feasibility of the method may be demonstrated. An extensive bibliography has been developed

Jan 1, 1977

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By Robert G. Clarke

The production of natural abrasives varied in quantity and value compared with those of 1974. Output of tripoli-type materials and garnet both decreased in quantity and value. Special silica stone products decreased in quantity but in-creased in value. The production of emery increased 38% in quantity. The production of manufactured abrasive materials decreased for all types and the decreases were more in quantity than in value. [ ] FOREIGN TRADE Imports of abrasive materials were 15% less in value than in 1974, and exports plus reexports decreased in value 10%. Net exports, the excess of exports and reexports over imports, were $9.3 million, about four times that of 1974. The volume of all abrasive materials exported decreased and the value of nearly all decreased.

Jan 1, 1977

By Juan Roldán

El presente trabajo refiere la política de creación, formación y futuro de la Escuela de Minas de Recuay en el ámbito de la minería nacional e internacional. Para ello, se revisa los fundamentos del proyecto, antecedentes, organización, formación y perfeccionamiento del personal, métodos de enseñanza y conclusiones.

Nov 1, 1976

By Ta M. Li, Russell A. Carter

The first century of mining in northern Idaho's Couer d'Alene District will soon he drawing to a close. Like so many other great raining districts, it has been a period accompanied by a rich and colorful history. From its early days as a gold rush camp, the district has evolved into the leading silver producer in the US, but the going has not been easy: early-day labor disputes, the challenge of mining for profit in some of the deepest mines in the Western hemisphere, and the constant search for new reserves at great depths have taken their toll of mines-and miners-along the way. To these traditional mining problems have of late been added the burden of inflationary cost increases, pollution control, and reclamation. A recent visit to the district by MINING ENGINEERING, how ever, revealed that the deep commitment of the operating companies and the quiet competence and vitality of their engineering personnel are key factors in the continued prosperity of the district.

Jan 7, 1976

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976