Search Documents

By Bruce Bryant

Silver ore was discovered at Aspen in 1879, but the district did not reach full production until 1888 after lawsuits were settled and railroads furnished less expensive transportation to the outside world. The boom years were 1888-92; production declined thereafter. From the middle 1920's until 1950, the Midnight mine in the Richmond Hill district furnished most of the output in the Aspen quadrangle. Since 1950, little mining has been done at Aspen. The metals produced were silver, lead and zinc. Native silver dissolved from the sulfide ores was redeposited by waters circulating as deep as 300 m below the land surface, resulting in great secondary enrichment of many of the deposits. Over 100 million ounces of silver were produced in the Aspen quadrangle. Low-grade lead-zinc deposits remain between the old workings locally, and data available suggest that primary ore below levels mined is also of low grade. The ore occurs in the Mississippian Leadville Limestone and the lower part of the Pennsylvanian Belden Formation in sites that were made favorable for deposition by a number of stratigraphic and structural factors.

Jan 1, 1982

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Basilio Ponce Pío

La industria minera busca reducir los costos de operación y optimizar la producción a través de una modernización de las operaciones minero metalúrgicas. Bajo esta premisa, la mina Uchuccahua utiliza un nuevo método de explotación denominado "explotación por subniveles con taladros largos". En este sentido, el presente texto señala la aplicación del método a través del block mineralizado de plata llamado "Claudia", cuya explotación alcanza también a las vetas que sean mayores de dos metros. Así también revisa la recuperación de un block mineralizado en la veta Irma Viviana, la cual estuvo abandonada por derrumbes al inicio de la explotación.

Apr 1, 1991

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP'd, HIP'd, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

By Raúl Hidalgo

El presente trabajo describe el plan estratégico de la mina San Vicente, ubicado en la provincia de Chanchamayo, departamento de Junín. Entre los objetivos de la mina está el aumento de la productividad a través de la reducción de costos de operación y realizar labores de pre-minado de 20 m/ día en los avances de operaciones. En este sentido, si bien la función del mecanizado es importante para el incremento de la productividad, es necesario controlar y administrar los recursos del nuevo yacimiento. Por ello, para implementar la nueva tecnología del minado es necesario el estudio de mecánicas de rocas y asi determinar la característica de la masa rocosa y la factiblidad económica para excavados mediante el sistema de minado contínuo.

Aug 26, 1988

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By Theodore H. Eyde

In 1971, the Minerals Division of The Superior Oil Company acquired exploration rights to an unpatented claim group in the Superior (Pioneer), Arizona mining district, lying west of the Concentrator fault. This major post-mineral fault displaces the Magma vein-fault, which is mined in the Magma Mine at Superior, Arizona. The Magma vein-fault and the enclosing section of pre-mineral rocks consisting of Paleozoic and younger Precambrian sediments and diabase, is overlain by a thick section of post-mineral rocks, consisting of the Gila conglomerate, the Apache Leap dacite, and the Whitetail conglomerate. Geologic information on the thickness and attitudes of the rocks obtained from previous diamond drilling indicated that the section of post-mineral rocks might be from 3,000 to over 4,010 feet thick in the target area. (Figure 1) The Magma vein-fault is a steeply dipping vein which has produced nearly a billion dollars of copper, zinc, silver, and gold. It has been mined continuously for nearly 10,000 feet along the strike and nearly 5,000, feet vertically down the dip. It ranges from less than a foot to over 50 feet wide and contains sulfide mineralization con¬sisting of pyrite, chalcopyrite, bornite, and chalcocite.

Jan 1, 1973

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By Jacinto Trujillo

Dado que la sociedad minera Corona se encontraba en constante cambios por la competición globalizada y redujo su rentabilidad económica, se planteó una serie de estrategias que optimizen el rendimiento en la unidad de Producción de Morococha. En este sentido, el presente trabajo describe los resultados de la aplicación de las estrategias operativas en la Mina Manuelita a través de tres principios sencillos: trabajo en equipo, ser el competidor de uno mismo y la evaluación de riesgos debe corresponderse con los resultados. Finalmente, los logros alcanzados se dieron por el apoyo de la Alta Gerencia y la responsabilidad y compromiso de todo el personal.

Sep 13, 2001

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By F. M. Nakla

Various methods of Applied Mineralogy were used for determining the nature and composition of products yielded by flotation tests for Maghara coal beneficiation. Coal samples obtained from the Sa fa mine in Northern Sinai, Egypt, were crushed, sieved, &apos;and <32 mesh size fraction was cleaned by froth flotation. Experiments were conducted to determine the effect of certain parameters on beneficiation of Maghara coal by flotation. The investigated factors included nature of frothing and/or collecting reagents, pH value of the medium, particle size distribution in the head sample, and pulp density of the coal slurry. The quality of head samples, coal concentrates, and tailing products were determined by chemical analysis, microscopic study, x-ray diffraction analysis, and occasionally by infrared (IR) absorption spectroscopy.

Jan 1, 1989

By José Ojeda

El presente texto describe los recursos alternativos para recuperar valores de los minerales oxidados de plata y plomo. Para lo cual se utiliza la floculación-flotación hidrofóbica, donde se espera que la segregación selectiva de partículas finas mejore la constante flotación y la cinética de flotación.

Nov 1, 2014

By A. KROENLEIN

THE Cromwell &apos;Pool has been the outstanding development in Oklahoma during the year 1924. . Tonkawa contributed the deep "Slick Sand" bit apparently its &apos;peak has been reached and like other pools producing from below the Mississippi lime its decline&apos; mill be rapid. After reaching a daily production of 67,000 bbl., the Cromwell Pool is declining because of a lull in -new completions, but a mile extension has revived activity and an area equal to that of the present producing&apos; area is under development and will cause an increase in the present production of 38,000 bbl. This pool is seven months old, has three dry holes in one hundred twenty completions and is actually defined only on the southern extremity. This area has been one of the chief contributors to the .over-production of high gravity oil in the Mid- continent fields and will be such&apos; for the remainder of &apos; the year. 1924 and first part of 1925.

Jan 1, 1924

By Erwin Olivera, Federico Salazar

En Minera las Bambas se implementó un modelo integrado de gestión dentro del área de Entrenamiento Mina con el objetivo de preparar, fortalecer, monitorear y revalidar las capacidades teóricas y prácticas de los operadores de equipo pesado, a través de, un adecuado proceso de entrenamiento que utiliza estándares, infraestructura y tecnología de primer nivel, agregando valor al ciclo de minado. Entre los años 2017 y 2019, se incrementó los equipos de la flota de mina para el futuro desarrollo del tajo, generándose una necesidad de reclutar, formar y adecuar operadores locales y externos; para lo cual se diseñó un proceso de entrenamiento seguro y eficiente.

Sep 30, 2022

By R. M. Gammell, S. H. Lorain

The Anderson prospect is one of a number of properties investigated by the Bureau of Mines during the course of preliminary studies of the lead-zinc districts of northern Stevens County, Washington. examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. This examination was supplemented in late 1944 and the spring of 1945 by pre- The property was first liminary angle-dozer trenching and core-drilling. A second examination of the property was made by the junior author in November 1945. The data obtained in the course of these studies is presented in the following report.

Mar 1, 1947