Search Documents

By Ralph Husack, J. W. Eckerd, G. A. Brady

The effect of gamma radiation on Pennsylvania anthracite and on reactions between anthracite and other materials was studied using a shielded , selfcontained 23,000 - curie cobalt 60 source . When anthracite was exposed to air at 65° C the reaction with oxygen was greater in the presence of radiation. than in its absence . Although drop- shatter tests indicated that exposure to radiation decreased the resistance to breakage of anthracite , this evidence of structural weakening was not supported by the results of grindability or particle- size studies . Irradiation caused definite changes in the gases evolved from evacuated samples of anthracite ; the percentages of hydrogen and carbon dioxide were increased, and the methane concentration remained unchanged . Carbon monoxide was evolved only from the unirradiated samples . Electron paramagnetic resonance (EPR ) measurements indicated large differences between evacuated samples and those exposed to air . There was little or no difference between irradiated and unirradiated samples , except that the free- radical content of unirradiated samples of anthracite increased progressively with higher temperatures of evacuation , but in the case of irradiated samples , no such behavior was found . Attempts to produce carbon disulfide and calcium carbide by reacting anthracite with sulfur up to 120 ° C , and with calcium oxide up to 400 ° C , were unsuccessful .

Jan 1, 1964

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

Alumina can be recovered from clay , using 30 percent nitric acid for digestion . Calcined clay is crushed and then digested at 325 ° F and 85 psig pressure with less than stoichiometric nitric acid required to form normal aluminum nitrate . In this way , a solution containing both normal aluminum nitrate , Al ( NO3 ) 3 , and basic aluminum nitrate , assumed to be Al ( OH ) ( NO3 ) 2 , is formed , and in which iron is virtually insoluble . The solution is filtered and then concentrated in vacuum evaporators to crystallize normal aluminum nonahydrate . The crystals are washed with 50 percent nitric acid and then decomposed to alumina and nitrogen oxides . The design that has been developed for this process is based on published work . For a plant producing 1,000 tons of alumina a day , the estimated operating cost is $60.69 per ton of alumina , and the estimated fixed capital cost is $ 76 million using a Marshall and Stevens chemical equipment index basis of 240.0 . This process is not competitive under current economic conditions with the production of alumina from bauxite via the Bayer process . For lowering costs , future research should include study of leaching at lower temperatures under atmospheric pressure and alternate aluminum nitrate decomposition methods .

Jan 1, 1964

By Stanton L. Tainter

When the disruption of gold mining stopped the usual source of siliceous flux needed by copper smelters , sandstone copper deposits in northern Arizona offered possibilities as a source of the flux during the war emergency . The Federal Geological Survey , while making a comprehensive survey of sandstone copper deposits , investigated the Warm Springs mining district in northcentral Coconino County in August 1943. A month later , J. H. Hedges , chief of the Tucson Division , Mining Branch , Bureau of Mines , examined the operations in connection with an application for an access road . Both investigations concluded that the district , as an emergency source of copper-bearing siliceous flux , had considerable merit , provided high prices for copper continued in effect . Early in 1944 , V. M. Ryan and S. B. Atherley requested assistance from the Bureau in exploring various deposits on their property . The Bureau / drilled 152 holes , aggregating 3,756 feet , on the Petoskey and Mackin groups of claims . This report is based upon churn drilling done under contract from October 7 to November 25 , 1944 .

Feb 1, 1947

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for industrial and defense sectors. REEs are not as rare as the word “rare” portrays; yet, the exploitable and/or profitable deposits of REEs may be found only in certain geographical areas. The political and social conditions characterizing these areas may not always be in favor of mining operations. These conditions are imposing the need for extra consideration on the geopolitical constraints prior to any decision-making and before any mining project begins. This study assesses the risk related to mining projects for areas that feature REE deposits based on a geopolitical viewpoint. Probable ranking differences between the current assessment and a 2015 assessment are discussed. The comparative indicators used and the appraisal procedure applied in this comparison are based on a number of different geopolitical indicators. Several ranking changes occurred between 2015 and 2019.

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser, T. Schirmer

At a time of resource consumption, it is important to study the chemical composition of mining and metallurgical wastes to prevent the dissipative loss of metals and metalloids from the mining value chain. In particular, the recovery of critical elements from wastes is an option to increase the resources of such materials that are economically significant and have an overall supply risk. In this paper we report on the chemical composition, in particular the critical element content, of granulated slag originating from historical smelting activities in the Tsumeb area, Namibia. Laboratory-based inductively coupled plasma–mass spectrometry (ICP-MS) and X-ray fluorescence (XRF) analyses as well as portable X-ray fluorescence (pXRF) demonstrate that the slags are on average enriched in base metals (Cu 0.7 wt%, Pb 2.7 wt%, Zn 4.7 wt%), trace metals and metalloids (Cd approx. 50 mg/kg, Mo approx. 910 mg/kg) as well as critical elements (As approx. 6300 mg/kg, Bi approx. 3 mg/kg, Co approx. 200 mg/kg, Ga approx. 100 mg/kg, In approx. 9 mg/kg, Sb approx. 470 mg/kg). While metals and metalloids such as As, Mo and Pb can be determined reliably using pXRF instruments, the technique has inherent limitations in evaluating the contents of certain critical elements (Ga, Sb). However, there are positive correlations between the As, Mo, and Pb contents determined by pXRF and the Ga and Sb contents obtained through ICP-MS and XRF. Thus, quantitative pXRF analysis for As, Mo, and Pb allows calculation of Ga and Sb abundances in the slags. This work demonstrates that pXRF analysers are a valuable tool to screen smelting slags for their chemical composition and to predict the likely contents of critical elements.

Mar 1, 2021

Laboratory tests were conducted by the U.S. Bureau of Mines to determine respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Increases in exhausting face ventilation from 3,000 to 9,000 cfm, in waterflow from 15 to 35 gpm, and in water nozzle operating pressure from 80 to 200 psi were evaluated. Results indicated that airflow had the greatest individual impact on reducing dust levels, with concentrations at return and operator sampling locations reduced by as much as 57% and 99%, respectively. Regression modeling was utilized to predict dust concentrations over the range of values tested for the control parameters. Interactions between the control parameters were significant and often defined an optimum level where further increases in that parameter failed to produce additional dust reductions. Increasing airflow to 8,400 cfm, waterflow to 25 gpm, and water pressure to 140 psi typically reduced dust concentrations at operator and return locations. Application of a control parameter above these levels can provide additional dust reductions if used in conjunction with appropriate levels of the other two control parameters. Otherwise, higher operator dust levels may result and can be attributed to increased rollback and/or airflow turbulence.

Jan 1, 2010

By Fred N. Kissell

This U.S. Bureau of Mines report is a guide for the control of air contaminants during tunnel construction. Topics discussed are calculating air quantity requirements, types of ventilation systems, planning ventilation systems, control of methane gas, control of dust, control of diesel emission, ventilation to remove blasting fumes, measuring airflow, and measuring gases. This report does not provide detailed design information, but seeks to answer practical questions on air contamination issues.

Jan 1, 1995

By James S. Grichar

Interest in mergers in the nonfuel mineral industry developed when 5 were listed among the 50 highest valued mergers in the United States in 1981. This report presents a Bureau of Mines study of trends in merger activity from 1960 to 1979 and explores motives for mergers in the nonfuel mining and mineral industry. The objective was to determine precedent for or a trend toward the 1981 acceleration in merger activity and to examine certain financial motives for non fuel mineral mergers. Data indicate that the relative value of non fuel mineral mergers has grown since 1972 although the number of mergers has remained proportionate to historical trends for all mergers. Since 1974, the assets acquired in "large," nonfuel mineral firm mergers, those of $10 million or more, have comprised at least 93 pct of assets acquired. More nonfuel mineral firm mergers involved mineral companies as the acquiring firm than vice versa but mining and minerals firms acquired were of higher value than nonmining firms. A major motivation for mergers involving large mineral firms was the acquisition of assets at less than replacement costs. Univariate statistical testing, a methodology chosen for its applicability to the data, confirms this hypothesis while rejecting other financial motives. The remainder of the work is devoted to a discussion of suggested areas for future study.

Jan 1, 1984

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By Robert H. Bedford

The New Almaden mine was discovered in 1824, and since that date production of quicksilver has exceeded 1,000,000 flasks. Because of this high production record, the New Almaden area was, upon passage. by Congress of the Strategic Minerals Act of 1939, immediately considered by the Bureau of Mines as a promising location for exploration. In 1941, the Federal Geological Survey undertook a survey of the entire district. R. R. Trengove, an engineer of the Bureau of Mines, made a preliminary study for a project in 1942, and in August 1943 the Bureau, in close cooperation with the U. S. Geological Survey, began the development project described herein. The Bureau of Mines drilled 36 holes, totaling 6,807 feet of diamond drilling, along the contact between the serpentine and Franciscan, sandstones and other sedimentary formations. The ore bodies are found along this contact and occur in the carbonate-silica rock. This report briefly describes the location, history, and ore deposits of the property. The recent operations are outlined, and the work performed by the Bureau is explained in detail.

Jan 1, 1950

By Thomas R. Bur

The patterns of variation of the 21 anisotropic elastic constants with direction arc presented for all of the symmetry systems that are normally expected to occur in rocks and in the constituent minerals. The exception, which is not discussed, is the triclinic system for which no elastic constants are available. Variations are shown for rotations about the principal axes by means of polar graphs. These include graphs for all of the n-fold symmetry axes possible for elastic symmetry and thus make it possible to visualize variational patterns for rotations about any n-fold axis. Variations throughout space are shown by means of equal area projections for the only constants (those relating axial stress to axial strain) that are uniquely defined by a single closed surface. For those unfamiliar with the compliance (Sij) and stiffness (cij) coefficients, the variations that can be shown by Young's modulus (E), Poisson's ratio (v), and shear modulus (G) are also given.

Jan 1, 2012

By L. Telfer

Summary During Palaeozoic time, there were deposited in the Canadian Rockies four beds of phosphate rock, ranging in age from Mississippian to Jurassic. Two of these beds are of probable economic importance if some means of separating the phosphate from the gangue can be devised. All the more important beds of phosphate rock so far discovered are just behind the front ranges of the Rocky mountains, within fifty miles of the prairie lands of Alberta. Mining conditions are favourable, with an abundance of timber and ample power available. The phosphate beds are all of the sedimentary type, and they all occur, apparently, at the same stratigraphic horizons over a wide area. The conditions necessary for deposition evidently occurred at several different periods in geological time, and were widespread. The most important factor appears to have been the condition of the land surface surrounding the basin of de-position. Both oolitic and nodular phosphate were laid down under nearly similar conditions. Introduction Following the discovery of phosphate rock in Idaho and Montana, search was commenced in Canada to determine whether formations of similar age in the Canadian Rockies carried similar beds of phosphate. The most widespread search has been that undertaken by the mines department of the Consolidated Mining and Smelting Company of Canada. The following paper will discuss some of the results of this exploration.

Jan 1, 1933

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

A series of petrological studies were carried out on the characteristics of alteration and mineralisation in mainly structural-controlled (Deep Star, Meikle, Deep Post) and predominantly lithological-controlled (Post-Betze-Screamer and West Leeville) gold deposits in the northern district of the Carlin trend, Nevada. Alteration and mineralisation in these deposits are hosted in a sequence of calcareous clastic units of the Devonian Popovich Formation, into which have been emplaced a number of Jurassic intrusions, and syn- to post-mineral Eocene dikes. Four hydrothermal events have been recognised in these deposits: an initial Devonian base metal system and early diagenesis; a Mississippian stage of alteration in conjunction with burial metamorphism; contact and hydrothermal alteration and base metal-gold mineralisation associated with the emplacement of the Jurassic intrusions; and a Carlin-style gold system related to Eocene magmatism.

Jan 1, 2004

By G. W. Elger

This report describes pilot-plant studies and an economic evaluation of a process developed by the Federal Bureau of Mines, Albany Metallurgy Research Center, to produce synthetic rutile from a rock-type ilmenite concentrate. In this process, ilmenite blended with coke and lime is smelted in an electric arc furnace to separate most of the iron as salable pig iron and to form a titania-enriched slag of low iron content, which is treated with oxygen and titanium pyrophosphate. The titanium oxides are converted to crystalline rutile; the phosphate glass contains most of the associated impurities. The treated slag is ground and leached with sulfuric acid to liberate rutile crystals, which are concentrated by physical methods. In pilot testing conducted to obtain data for a cost estimation, a synthesized product containing about 88 wt-pct TiO2 and less than 2 pct FeO was extracted from a rock-type ilmenite concentrate containing about 45 wt-pct TiO2. The estimated fixed capital cost (on a mid-1975 basis) of a plant producing 500 tpd of synthetic rutile is $28,290,100. Based on 330 operating days per year, the estimated operating cost for this process is $351 per ton of synthetic rutile. The estimated selling price of synthetic rutile made from rock-type ilmenite is $344 per ton, based on a credit of $160 per ton of pig iron and a 20 pct interest rate of return on investment after taxes.

Jan 1, 1976