Search Documents

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By G. L. Oldright

Nearly all of the present schemes for treating complex (i. e. lead-silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient to compensate for the additional expense involved in beneficiating these ores. The smelters have bad to meet the same general economic situation, so they can only give

Jan 1, 1924

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON' discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

By Thomas A. Simpson

THE Birmingham red iron ore district in Jefferson County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons. The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production, and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country.

Jan 1, 1955

By Hsun Hu

The formation of annealing textures in high-purity silver, from the various rolling textures obtanled in the course of texture transition, was studied. It was found that from a brass-type rolling texture the recrystallization texture is mainly (120) [211] type, which is quite different from the recrystallization texture of brass. From a predominantly copper-type rolling texture, the reclystallization texture is mainly (100) [001]. The recrystallization texture of silver- varies also with the degree of purity. In each case, however, the reorientation can be expressed as [Ill] rotations of 30° to 40°, which is consistent with the oriented growth theory of the formation of annealing textures. ThE recrystallization textures of rolled silver were studied long ago by Glocker and co-workers (1924-27) and were reported to be (113) [iil] upon annealing at low temperatures.1 Since that time, no further study of the recrystallization textures of silver, particularly with the modern techniques of quantitative texture determinations, has been reported in the literature. In a previous study2y3 it was found that the rolling texture of high-purity silver (99.999 +pct pure) is changed gradually from the common silver- or brass-type to the copper-type by raising the temperature of rolling from 0" to 200°C. The formation of annealing textures from the various rolling textures in the same material is, therefore, of considerable interest. The present paper constitutes the results of such a study. MATERIAL AND METHOD Specimens were taken from the same strips of high-purity silver* that were used previously for

Jan 1, 1962

By H. Firmstone

DEPOSITS of cadmia, or impure oxide of zinc, are of common occurrence in the upper parts of blast furnaces using ores containing zinc, and were very common in the charcoal furnaces of Virginia working the brown hematite ores found near the Cadent black slate. These deposits were known to the old charcoal founders as "sulphur rings," and the characteristic green flame of burning zinc frequently to be seen at the tymp of furnaces working ores containing zinc, was held by them to indicate the presence of a "sulphur fall." When zinc is burning in considerable quantities at the tymp, the

Jan 1, 1879

By Dale Dixon, A. R. MacPherson

The present comminution process in principle has remained more or less the same for the last 50 years. The majority of the changes have been in the fields of equipment improvements and size increases of prevailing systems. The development and utilization of completely new systems has virtually been non-existent. As energy and steeel costs increase and lower grade ores are mined, the comminution costs per ton of ore treated must improve accordingly or the operations will not be profitable. The chapter examines further developments in existing systems and touches on relatively unexplored methods of comminution appropriate for future needs.

Jan 1, 1982

Just three years after researchers announced its development, Dravo is putting the finishing touches on a new $60-million Thiosorhic lime mine/kiln complex near Maysville, Ky. Electric utilities in western Pennsylvania and Ohio have already signed long-term contracts for over three-quarters of the projected 907 000-t/v (1-million-stpy) production. Thiosorbic lime, a flue gas desulfurizing agent, proved in industrial testing that at high emission levels (greater than 3000ppm SO2) it could be twice as effective in SO2 capture as conventional lime, while eliminating the major problem of scaling and plugging of scrubber equipment.

Jan 4, 1977

By E. E. Bach

STATEMENT OF THE PROBLEM THE administration of industrial organization today embraces more than the cost of production and selling prices. Competition is deeper seated than mechanical devices, overhead charges, and a shrewd manipulation of the markets. Despite the "down-to-the-minute" equipment and the "last word in organization," it is quite evident that "capacity production" will be an unknown quantity until the workman is considered as a producer, in relation to his home, as he is now considered in relation to industry. Whether or not a man shall do an honest day's work is as much a psychological condition as it is a matter of physical strength or skill. His attitude toward his work each morning is determined, to a large degree, by the environment of his home. Whether this attitude, good or bad, obtains the day through will depend entirely upon the one fact as to whether the corporation which employs him does or does not differentiate between the mechanical factor and the human factor in industry. To be more specific, sociological work, under whatever name, should be of such a character as to influence the life of a workman in such a manner as to establish a cooperative interest in his work, foster within him a spirit of contentment in his home, lead him-so to employ his leisure time that he will not lower his efficiency as a workman, destroy his domestic happiness, or endanger his standing in the community as a citizen. While no fixed rules of procedure can well be formulated for the development of the work, yet definite lines of activities will readily present themselves as applicable to the individual needs of a community. This is especially true where community influences and agencies pertaining to general welfare are easily correlated.

Jan 2, 1918

By C. W. Hamilton

In the production of crude petroleum for the year 1930 Venezuela again maintained its world rank of second only to the United States. During the latter months of the year Russia forged ahead of Venezuela in daily rate of production, and from the present outlook will probably rank second among the oil-producing countries of the world in 1931. It is now believed Venezuelan production has passed its peak. The producing fields of the Bolivar coastal district, along the east side of Lake Maracaibo, continue to be the principal source of supply. Such fields as Lagunillas, Mene Grande and La Pas were not produced to capacity throughout 1930. During the year, three new fields entered into commercial development: The Rio Tarra field in the District of Colon, State of Zulia; the El Mene de Salto field in the District of Acosta, State of Falcon and the Quiriquire field, District of Piar, State of Monagas. For 1930 the total crude production of Venezuela was approximately 137,424,000 bbl. as compared to 137,739,000 bbl. during 1929, or a decrease of 315,000 bbl. During the past year exports of crude from Venezuela amounted to 137,8.50,000 bbl. as against 130,044,000 bbl. exported during 1929. Crude oil in field storage decreased from 14,138,-000 bbl. at the beginning of 1930 to 9,600,000 bbl. as of Jan. 1, 1931— present crude stocks fill about one half the field tankage available. Drilling operations in the producing fields declined sharply but throughout the year there was maintained a satisfactory potential reserve in the shape of proven territory and closed-in producers. Of the 2555 wells which have been completed in Venezuela, 1571 wells were in production on Jan. 1, 1931. The status of these present producing wells may be classified as follows: flowing 652, pumping 170, gas-air lift 193 and closed-in 556. The ratio of closed-in wells to producing wells declined in 1930, while the number of wells produced by artificial means increased materially. In the Bolivar coastal fields there is now observed a marked decline in gas volume and well-head pressure. Lago Petroleum Corpn. and Venezuela Gulf Oil Co. each have under construction electric plants designed to generate power for pumping wells by electricity. The first units of these plants will be placed in conlmission in the early spring of 1931. Venezuela Oil Concessions, Ltd. has installed a number of stenrn-

Jan 1, 1931

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By Henry D. Hibbard

A noted ordnance engineer once said to a friend, in speaking of the production of great steel guns, " How is it ? We design our guns with a factor of safety of eight, and the guns burst." The vague way in which internal stresses and strains in iron and steel are often considered and spoken of makes it worth while to examine them, as to their nature, their causes and results, how they may, for useful purposes, be advantageously dealt with, and how, when detrimental or dangerous, they may be reduced or kept within harmless proportions. Rankine defines " strain " as a change of form or dimensions of a solid or liquid mass produced by a stress. This definition seems intended not to cover strains due to internal stresses, and it will help us in the present inquiry to consider strain as a tendency to change as well as an actual change of form. Internal strains in iron and steel are the result of stresses within the mass of the piece, some parts pulling and others pushing in resistance to them; or, in other words, some parts are in tension and some in compression, each part striving to relieve itself from strain and make the piece assume a form in which all parts are at rest. Subdivision, so that each part could relieve its strain by motion relative to the other parts, would, if carried out far enough, practically obliterate strain. The internal strains we are now to consider are not those due to the stresses of the service which the piece is rendering, either alone or as a part of a structure, which may be termed service-strains, but those which originate or at least are contained in the piece itself. Internal stresses in a piece of metal are, like action and reaction, always equal and in opposite directions. The stresses

Jan 1, 1907

By B. L. Dunic, Terkel Rosenqvist

rr has long been suspected that sulphur has a small but finite solid solubility in iron, but up to the present more accurate data have been lacking. The survey given by Hansen' illustrates the divergence of data and opinions. Solubilities between 0.01 and 1.5 pct have been suggested, and opinions vary regarding the effects of temperature and phase transformations in iron on the sulphur solubility. The extent of solid solution and its variation with temperature might be expected to be an important factor in the occurrence of hot shortness in steel. Therefore, the object of the present investigation was to study this problem more systematically. It was furthermore hoped that solubility data for sulphur might contribute to an understanding of the factors which determine solid solubilities in general. Experimental Procedure The present work was based on the measurement of the chemical activity of sulphur in the solid solution by means of equilibrium with a mixture of hydrogen and hydrogen sulphide. When the solid solubility limit is reached, the sulphur activity in the iron becomes equal to that in the coexisting sulphide phase. A gas mixture of a controlled H,S/H, ratio was passed over pure metallic iron heated to a temperature in the range 900" to 1500". The amount of sulphur absorbed by the iron was determined by analysis, and from a plot of percentage of sulphur vs. gas composition the sulphur activity and the solubility limit were determined. As the rate of diffusion of sulphur in solid iron is very small, often several days were needed to be sure that equilibrium conditions had been established. To produce a gas flow with less than 1 pct H,S of constant composition for several days, was in itself a problem. The most satisfactory arrangement was obtained by a continuous synthesis of hydrogen sulphide from the elements. This was done in the part of the apparatus shown to the left in Fig. 1. The hydrogen used was first purified in tank batches by passage through activated charcoal cooled in liquid nitrogen under a pressure of 150

Jan 1, 1953

By Victor F. Hollister

North American ophiolite complexes are known to contain significant volcanogenic sulfide only in the following five areas: Newfoundland; Quebec; Applegate, Oregon; Rogue, Oregon; and Orca, Alaska. Most North American ophiolites, including the Baltimore, Kings-Sierra Nevada, and Del Puerto complexes, and those associated with the Franciscan, Trinity, eastern Oregon, and Cache Creek groups lack significant volcanogenic sulfide. The characteristics of sulfide-bearing ophiolites are: (1) manganozls cherts, and (2) fine, carbonaceous clastics inter- calated with pillow basalt and chert. It is suggested that sulfide- bearing ophiolite complexes developed in a restricted basin environment, such as is now present in the Gulf of California; whereas sulfide-poor ophiolites, formed in midocean, rises distant from land masses. Sea floor oxidation makes the typical midocean ridge configuration not conducive to sulfde preservation, whereas spreading centers bounded by land masses are more likely to produce anoxic physiographic lows favorable to sulfide accumulation.

Jan 1, 1982

By H. M. Morse

There was little change in the oil and gas industry in Mississippi during the year 1938. No new fields were discovered and the production from the Amory field was nil. In the Jackson gas field six wells were drilled and production was obtained in each instance, but none of these wells increased the area from which the gas is produced. Outside the Jackson gas field nine wells were drilled, of which details are given in the accompanying table. The seeming lack of activity in Mississippi belied what was actually happening, for a great many geophysical crews of the major companies were active in all parts of the state. There were approximately 65 structures mapped and for the most part these have been leased. It is believed that 1939 will see an increase in wildcatting over a large part of the state.

Jan 1, 1939

By H. M. Morse

There was little change in the oil and gas industry in Mississippi during the year 1938. No new fields were discovered and the production from the Amory field was nil. In the Jackson gas field six wells were drilled and production was obtained in each instance, but none of these wells increased the area from which the gas is produced. Outside the Jackson gas field nine wells were drilled, of which details are given in the accompanying table. The seeming lack of activity in Mississippi belied what was actually happening, for a great many geophysical crews of the major companies were active in all parts of the state. There were approximately 65 structures mapped and for the most part these have been leased. It is believed that 1939 will see an increase in wildcatting over a large part of the state.

Jan 1, 1939

The early history of a country is linked with its topographic features. Mountains are barriers, rivers are avenues, the sea is a highway. The first Europeans to reach the northwestern corner of the American continent, now known as Alaska, came from Asia, for the Pacific Ocean provided an approach by means of the islands that like stepping-stones stretch far westward from the inhospitable shore of the mainland. The Russians crossed Siberia and explored the Arctic coast of Asia. In 1728 a band of Cossacks was driven by a storm eastward from Kamchatka, and landed in Norton Sound.* Others followed them, and settled on the islands and peninsulas of southeastern Alaska. The mountains guarding the coast discouraged any advance into the interior. Another range, the northern extension of the Rocky Mountains, barred the westward progress of the French voyageurs and the English fur-traders of the Hudson's Bay Company. After the Russians had obtained a foothold among the Indians, the viceroys of Mexico sent successive expeditions up the coast, such as that of Pérez in 1774 and of Heceta in 1775. If the English fur-traders had not interfered, the Spanish and Russian spheres of influence would have conflicted, and the contest for control might have ended in establishing a line of demarkation somewhere near the mouth of the Columbia river. The British navigator Captain James Cook landed near Sitka in 1778 while seeking a way by water to Hudson Bay. Fifteen years later his midshipman, George Vancouver, in command of another British expedition, surveyed the coast

Jan 1, 1932

By M. J. Langley

The American Zinc Company’s mining operations in East Tennessee are located in Knox and Jefferson Counties. Mineralization occurs, intermittently, through a strike length of more than 30 miles, from near the eastern edge of Knoxville northeastward to a few miles beyond Jefferson City. The presence of zinc in these Counties has been known for well over 100 years. In 1910 it was brought to the attention of American Zinc Company that zinc sulphide deposits in the Mascot area might be attractive. Following an examination and some surface prospect drilling, the American Zinc Company of Tennessee was organized and acquired the Mascot properties in 1911. Operations began in 1913 on the basis of 1,000 tons per day mill capacity. With the successful operation of the Mascot mines, the Company undertook explorations in the area from Jefferson City southwest through Friends Station to Mascot. The efforts resulted in development of substantial tonnages of zinc ore and enabled the Company to expand the Mascot and New Market milling operations to their present capacity of 11,100 tons per day. Folded and faulted Paleozoic sedimentary rocks under- lie the mining district. The principal zinc mineralization occurs in a group of strata known as the Knox

Jan 1, 1970

By V. Miller

Highly variable milling procedures within a geologically complex porphyry copper deposit owned by Kennecott Corp. in Nevada made it necessary to estimate copper recovery and concentrate grade in areas where actual test data was lacking. Estimation was made by first determining the relationships between desired metallurgical properties and the ore's petrology-copper mineral type, rock type, and copper grade. This relationship was then combined with previously estimated rock type, mineral type, and copper grade data in the mineral block model to predict milling properties.

Jan 1, 1985