Search Documents

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace 'Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier's experiment................ 248 2. Wolkoff's experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914

By R. J. Keene

The South Works high-tonnage billet caster was started in late March 1971, with the first heat being successfully cast to completion. Currently, over 31,500 tons per month are being produced. U. S. Steel designed and built this caster with the objective of producing quality-steel billets for critical bar, rod, and wire applications. The essential design parameters were based on studies conducted on the Research Laboratory's pilot caster, also located at South works. 1,2,3)* The caster is a four-strand, straight-mold machine that produces 7.5-inch- square billets at rates exceeding 300 tons per hour. An in-line-reduction mill reduces each strand to either 6-inch-, 5-inch-, or 4-inch-square billets.

Jan 1, 1972

By Ben E. Lusk

During the past five years, the surface mining industry in Appalachia has launched itself into a technological revolution, which has never been equaled during a similar period of time. Operators have begun to realize that effectively restoring land to a useful purpose, to the satisfaction of all concerned, has to start at the beginning of the operation and be an integrated part of it throughout. In order to insure continued mining in the mountainous areas, with protection of aesthetic beauty, things really have had to change. And so the new steep slope mining theory of "controlled placement" has been developed. Controlled placement is a broad term which means the placement of spoil in steep areas where its condition can be completely stabilized and revegetated. This includes the head of valley fill, mountain top removal, haulback, over the shoulder, block cut, and any other methods where the over-burden is technically delivered, hauled, or compacted, so that there is no adverse after effects when mining has been completed. [(Fig. 1)] Under controlled placement, our whole approach to mining has changed. Before any displacement of soil or uncovering of the coal seam transpires, a complete drainage system

Jan 1, 1977

By G. R. Pickett

Examples are presented which show that the velocity~ amplitude, attenuation and apparent frequency of several acoustic waves can be recorded in the borehole. Examination of such recordings, termed "character" logs, indicates that the wave types observed include a refracted compressional wave and a wave which travels with formation shear velocity. Laboratory data are used to show that compressional and shear wave velocities are dependent on porosity, effective stress and lithology; but that the change in reciprocal velocity per unit change in porosity is larger for shear waves than for compressional waves. We, therefore, conclude that. the accuracy of porosity determinations can sometimes be improved by use of shear wave velocities, provided that the shear wave amplitudes are large enough to delineate the shear arrival from the preceding compressional arrival on the character log. Borehole data are presented which show that the difference between shear wave and compressional wave reciprocal velocities can be used to predict porosities. This is a refinement which may allow the prediction of porosities from single-receiver acoustic logs without introduction of errors from borehole fluid traveltimes. Laboratory and field data are presented to show that the relationship between compressional and shear wave velocities can be used to indicate lithology. An example is presented to show that fractures usually cause a greater reduction in borehole shear wave amplitudes than in compressional wave amplitudes, an effect which may offer a more reliable means of detecting fractures. The complexity of the borehole acoustic wave train can rake presently available cement bond logs highly sensitive to the gate and bias settings used. The character log offers a means to circumvent possible misinterpretations by recording all amplitudes, from which the interpreter can select the appropriate data for evaluating the cement bond. Character logs may also be used as a quality control for open-hole transit-time logs when existence of small compressional wave amplitudes interferes with the proper functioning of bias-controlled timing devices. Evaluation of the potential uses of character log data is not complete; but a character log presented in a form convenient for routine use would be a desirable addition to currently available logs. To summarize, possible applications for such a log in formation evaluation include the following (1) quality control of transit-time logs, (2) refinement of porosity predictions, (3) determination of lithology, (4) improvement of fracture detection and (5) improvement of cement bond evaluation. Suggestions are made regarding the requirements for a suficient but practical character log for routine use. INTRODUCTION Acoustic logs have become a widely used porosity tool in formation evaluation. In addition, there is a growing application of acoustic logs in cement bond evaluation and fracture detection. These applications have mainly involved the use of logs of first-arrival transit times and amplitudes and have not included detailed studies of the complete signal. The purpose of this paper is to show that significant benefits in formation evaluation can be gained by a more complete use of the acoustic wave train generated in the borehole by an acoustic logging tool. We hope that this discussion will also stimulate further development of logs suitable for routine use so that these benefits may be realized. Examples of acoustic wave train logs, termed "character" logs, are presented to show that several identifiable acoustic waves are present in the borehole. The measurable characteristics of these acoustic waves and some of their relations to formation properties of interest are also discussed. The more obvious potential uses of character logs are listed, and some suggestions are made regarding the requirements for a sufficient but practical character log for routine use. CHARACTER LOGS Some 10 years ago, Vogel' and Summers and Broding' noted that the signals received uphole from an acoustic logging tool located in a borehole had a number of interesting characteristics. The logging tool consisted of two or more pressure transducers spaced on an acoustically insulated body (Fig. la). One of the pressure transducers was used as a transmitter to generate pressure waves in the borehole fluid. The other transducer served as a receiver to detect any pressure waves reaching it in the borehole. The receiver then converted these pressure waves to electrical signals which were transmitted to the surface and displayed on an oscilloscope as a record of time vs receiver-signal amplitude. Fig. lb is a schematic representation of a typical record. The interesting characteristics seen in the earlier' and subsequent experiments were (1)

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

By Richard Zinszer

Application of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (1) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable correc- tions for sand thickness. The proceduer in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory. In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 ft., 16 ft., and 24 ft. thick, and found the observed resistivity Of the 8-ft. sand to be approximately

Jan 1, 1943

By Richard Zinszer

Application of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (1) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable correc- tions for sand thickness. The proceduer in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory. In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 ft., 16 ft., and 24 ft. thick, and found the observed resistivity Of the 8-ft. sand to be approximately

Jan 1, 1943

By A. Paul Bond

Two series of 17pct Cr iron-base alloys with small, controlled amounts of carbon and nitrogen were vacuum-melted in an effort to detertmine the meclz-uniswls of inter granulur corrosion in ferritic stain-less steels. An alloy containing 0.0095 pct N aid 0.002 pct C was very resistant to intergranular corrosion, even after sensitizing heat treatments at 1700" to 2100o F. However, alloys containing more than 0.022 pct Ni and more than 0.012 pct C were quite susceptible to intergranular corrosion after sensitizing heat treatments at temperatures higher than 1700°F. This corrosion was observed after the usual exposure tests and after potentiostatic polarization tests. Electronmicroscopic examination of the alloys susceptible to intergranular corvosion revealed a small grain boundary precipitate; this precipitate was absent in the alloys not susceptible to such corrosion. Thc electronmicrographs indicate that intergranu1ar corrosion of ferritic stainless steels is caused by the depletion of chromium in areas adjacent to precipi-tates of chromium carbide or chromium nitride. It also seems likely that the precipitates themselves are attacked at highly oxidizing potentials. Confirma-tion of the proposed mechanisms was obtained in tests on air-melted ferritic stainless steels containing titanium. The titanium additions greatly reduced susceptibility to intergranular corrosion at moderately oxidizing potentials but had no beneficial effect at highly oxidizing potentials. A major obstacle to the use of ferritic stainless steel has been their susceptibility to intergranular corrosion after welding or improper heat treatment. It appears that sensitization of ferritic stainless steel occurs under a wider range of conditions than for austenitic steels. In addition, a greater number of environments lead to damaging intergranular corrosion of sensitized ferritic stainless steels than to sensitized austenitic steels. The chromium depletion theory of intergranular corrosion is widely accepted for austenitic stainless steels'" although there: are some objections.3 On the other hand, several alternative mechanisms proposed for ferritic stainless steels include precipitation of easily corroded iron carbides at grain boundaries,' grain boundary precipitates that strain the metal lat-tice,5 and the formation of austenite at the grain bound-arie.6 The application of the chromium depletion theory to ferritic stainless steels has been discussed extensively by Baumel.7 The present investigation was undertaken to determine which of the proposed mechanisms can be sub- A PAUL BOND IS Research Group Leader, Climax Molybdenum Co of Michigan, Ann Arbor, Mich. stantiated with experimental data obtained on ferritic stainless steels. High-purity 17 pct Cr alloys containing small controlled additions of carbon or nitrogen were therefore prepared, and then examined electro-chemically and metallographically. EXPERIMENTAL PROCEDURES Materials. Two series of experimental alloys were prepared from electrolytic iron and low-carbon ferro-chromium using the split-heat technique. In this technique, the base composition is melted, and part of the melt is poured off to produce an ingot. To the balance of the melt, the required addition is made and the next ingot cast. This process is repeated until a series of the desired compositions is cast. By this procedure the impurity levels are essentially constant within each series. All the alloys in the carbon-containing series were melted and cast in vacuum. The base composition in the nitrogen series was melted and cast in vacuum; subsequent ingots in the series were melted with additions of high-nitrogen ferrochromium, and cast under argon at a pressure of 0.5 atmosphere. Two additional alloys were produced starting with normal purity materials. They were induction-melted while protected by an argon blanket and cast in air. Table I gives the composition of the alloys. The 2-in.-diam ingots produced were hot-forged and hot-rolled to a thickness of 0.3 in. and then cold-rolled to 0.15 in. All specimens were annealed at 1450°F for 1 hr. The indicated sensitizing heat treat-s s ments were performed on annealed material. All heat treatments were followed by a water quench. Specimen Preparation. For the 65 pct nitric acid test, 1 by 2 by 0.14-in. specimens were wet-surface ground to remove surface irregularities and polished through 3/0 dry metallographic paper. For the modified Strauss test, $ by 3 by 0.14-in. specinlens were similarly prepared. Immediately prior to testing, the Table I. Compositions of the Alloys Composition, pct Alloy Cr hio C N 270A 16.76 0.0021 0.0095 270B 16.74 0.0025 0.022 270C 16.87 0.0031 0.032 270D 16.71 0.0044 0.057 271A 16.81 0.012 0.0089 27 IB 16.76 0.018 0.0089 271C 16.69 0.027 0.0085 271D 16.81 0.061 0.0O71 4073' 18.45 1.97 0.034 0.045 4075† 18.5 2.0 0.03 0.03

Jan 1, 1970

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

By M. J. Marcinkowski, R. M. Fisher

The flow stress-grain size relationship has been determined at room temperature in both a disordered and a fully ordered FeCo for plastic strains up to 30 pct. The results are in agreement with a Hall-Petch relation of the type given by Of =a,+kd-1/2 where of is the flour stress and a, increases mono-tonically with increasing strain to a maximum value which is much higher for the ordered than for the disordered alloy. The slope, k, is found to increase FOLLOWING the original work of Halll and petch relating the effect of grain size to the lower yield stress of iron and steel, it has been generally found that the yield stress oy.s. of polycrystalline metals with strain to a maximum and then decrease for both ordered and disordered alloys. However, k for the ordered alloy is in general higher than that for the disordered alloy and the critical strain for k max somewhat larger. All of these observations can be satisfactorily accounted for quantitatively and in some cases semiquantitatively by using a slip band-grain boundary intersection model, and by taking note of the fact that, in general, moss slip, while quite common in the disordered alloy, is extremely difficult in the ordered alloy. obeys a relation of the form oy.s.=a0+kd-1/2 [1] where a, and k are constants and d is the mean grain diameter. For convenience, and in accord with prevailing custom, Eq. [I] will be referred to simply as the Petch relation. Tjerkstra3 and Armstrong, Codd, Douthwaite, and petch4 showed that the flow stress af of iron or steel measured at strains of up to at least 20 pct also obeyed a relationship of the type given by Eq. (11. The latter investigators have also shown that Eq. [I] applies to fcc and hcp metals and alloys.

Jan 1, 1965

By W. Kane, M. Karmis

Roof and rib failures in underground coal mines are one of the major problems facing the industry today. In addition to safety considerations, the resulting economic impact of such failures is staggering. Uncovering and replacing buried and damaged equipment and clearing entries can account for a large expenditure in lost man-hours and machinery. Yet, because of the complex nature of its formation, geological variability, and structural characteristics, coal mine roof strata is one of the least controlable of all mine design parameters. This is especially true along the leading (southeastern) edge of the Appalachian coalfields where considerable faulting and movement has contributed to hazardous coal mining roof conditions. During this research, a detailed study of several mines, in the southern Appalachian coalfields, was undertaken to determine the most prominent geomechanical factors affecting roof stability and to evaluate their influence in promoting unstable ground conditions. In order to accomplish this task, the major geological and geomechanical features found to be detrimental to coal mine roof within the Appalachian basin were identified and mapped in four Virginia mines. Statistical processing by chi-square and regression analysis was used to determine the influence of geology, mine-layout, and support methods on roof stability. It was found that some easily determined parameters can be successfully used to predict potentially unstable areas. A simplified roof classification system was developed based on these geomechanical parameters, which can be used to assess the stability of a particular roof type. A roof rating index was also devised capable' of expressing the probability of a failure under a given set geomechanical condition.

Jan 1, 1984

By Louis A. Carapella, Ralph Hultgren

WHEN F. Heusler1 found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.3 All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys" the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intelligently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. PREVIOUS WORK In the original work of F. Heusler1 and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for Cu2MnA1 of I = 443 was early measured. Ross and Grays found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 then reinvestigated the system, confirmed their results,

Jan 1, 1941

By F. H. Willcox

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J.).-This paper is timely because of the changed conditions due to the great war, but apparently its scope is limited to oxidation process steels. Referring to the four numbered observations on page 199: No. 1 seems to ignore Johnson's discoveries about oxygen in cast iron. No. 2 ignores crucible steel. No. 3 ignores red short steel containing enough gas solvents to make it solid, while No. 4 assumes that a deoxidizer is necessarily a gas decomposer or solvent and vice versa, which it not always is. From these observations it is deduced. that the only hole-forming gas in steel is an oxide of carbon (CO presumably is meant), which is not true.

Jan 4, 1917

By W. C. Hagel, H. J. Beattie

Variations in the secondary phase reactions of six nickel-and cobalt-base alloys were determined as a function of solu-tioning from 1700" to 2200°F and aging at 1200" to 1800° F for times up to 1000 hr. Room-temperature impact energies and hardnesses were also measured. Precipitation hardening of these alloys results mainly from the grain-interior formation of ? '; M23C6 appears principally as grazn-boundary cells which can be eliminated by intermediate high-temperature aging treatments. Cellular precipitation of ?' occurs up to 1500°F in cobalt-nickel alloys devoid of chromium, where precipitation by this mode can be attributed to a large degree of lattice disvegistery. THE usefulness of nickel- and cobalt-base alloys is dependent on balancing the strength and ductility provided by the solid-solution matrix, dislocation-type subboundaries, grain-boundary phases and genera1 precipitation within individual grains. Since equilibrium relationships for complex austenitic alloys are not easily fixed, a satisfactory balance

Jan 1, 1960

By D. D. Porter, C. Fairhurst

Crack propagation in the region of a statically pressurized borehole is investigated to determine a role of the sustained borehole pressure following detonation in a blast. The case of a single-hole bench blast is reduced to a plate model, which is considered both theoretically and experimentally. Based on the principle of least work, it is hypothesized that the path of any crack in the plate will coincide with one of a family of maximum principal stress trajectories. These trajectories were computed, and critical experiments in glass, designed to test the effects of controlled crack origin and of changed trajectories from different loading configurations, confirm this hypothesis. It is concluded that under ideal conditions the crack path can be predicted and that cracks can be produced in the absence of either high-amplitude stresses or stress waves. Energy considerations for crack extension are discussed, and, based on the strain energy distribution, a relationship between hole burdens and spacings is revealed, a critical burden is demonstrated, and a maximum crater width is shown to exist.

Jan 1, 1971

By Harry R. Hall

THE proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the successful work that has been done under these adverse conditions warrants a permanent record in our Transactions, especially as it furnishes a comparison with, coke blast-furnace practice under similar conditions. The record of the furnace-practice is briefly summarized as follows:-The charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates containing from 62 to 65 per cent. of iron would pass in. screen, of which about 34 per cent.. would pass an 80-mesh sieve. The cobbed ore, varying in composition from 32 to 47 per cent. metallic iron and from 23 to 32 per cent. of. silica, would pass through a I-in. ring, of which about 25 per cent. would pass a 1/8 in. screen. The furnace was blown in October 20,1903, with charcoal which was supposed to weigh when dry 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year and was then found to weigh 12 lb. per bushel. During the first 10 days of the blast, the furnace produced 362 tons of pig-iron, using 200 bushels of charcoal per ton of iron. From November 1st to 12th, the volume of the blast was increased gradually from 2,808 to 5,460 cu. ft. per minute, with practically no increase of output. The silicon-content of the resultant pig-iron averaged 0.75 per cent., with sulphur about 0.035 per cent. A supply of freshly-burned dry charcoal was then used which increased the silicon-content and lowered

Sep 1, 1905

By H. W. Miller, V. H. Wilhem

Although the year 1933 was a period of uncertainty, considerable new development was initiated, with a high percentage of favorable results, for owing to financial conditions only projects of merit were proposed and developed. Unfavorable marketing conditions caused severe financial losses to refinery and sales departments of nearly all companies during the first half of the year. In anticipation of stabilized Government control, earnings were generally favorable during the third quarter but failure of the Government to take legal action against violators of the proration orders, and lack of agreement on a definite plan of curtailment, resulted in considerable overproduction and demoralization of the market structure during most of the final quarter. However, toward the close of the year Government action against violators of the Oil Code had a tendency to decrease overproduction materially and give the market a firmer tone. As a whole, the price structure of crude oil was maintained at a high level during the year; in fact, at a much higher level than the price of refinery products warranted. At no time during the year was production within 10,000 bbl. daily of the state allotment, overproduction of crude reaching a peak of 70,000 bbl. on Sept. 7, average daily average for the year being about 27,000 barrels. Numerous plans for equitable curtailment were prepared and tested during the year, none of which fully solved the many and intricate problems faced by operators who were in most cases willing to curtail if they could feel that cooperation was being practiced by their neighbors. Outstanding events in California oildom during the period under discussion may be classified under the following headings: 1. New discoveries. (a) New development in proven areas. (b) Deeper zones in settled pools. 2. Unproductive wildcat operations. 3. Whipstocking practice and procedure. 4. Progress of unit and orderly plans of development.

Jan 1, 1934

By C. G. Dunn, J. L. Walter

COULOMB' and Coulomb and Lacombe2,3 have recently discussed secondary recrystallization in soft iron (99.5 pct Fe). They found that the appearance of this phenomenon was dependent on both the presence of impurities and the thickness of sheet specimens. They concluded that impurities such as carbon, sulfur, and oxygen in the soft iron stabilized the matrix structure and allowed growth of a few grains of specific orientations. They also found that secondary recrystallization ceased when the final thickness was small and attributed this complete inhibition of growth in thin sheet to the restraining action of thermal grooves. When purer iron (99.99 pct Fe) was used, normal grain growth but not secondary recrystallization was obtained. On the other hand it is known that the necessary stabilization of the matrix structure for secondary recrystallization in high-purity silicon iron probably does not depend on impurities but more likely results from the specimen thickness effect of Beck et al.,4 according to evidence and ideas advanced by Walter and Dunn,5,6 and Detert.7 Furthermore, Mullins8 has indicated that if a gas-metal surface energy difference exists across a grain boundary equal to or greater than about 3 pct of the grain boundary energy, then such a grain boundary should not become stuck. Similarly, Walter and Dunn have estimated that any increase in restraining force due to increased thermal grooving with decrease in

Jan 1, 1962

By W. A. Clark

THE production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl, of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. REASONS FOR GRAVEL-PACKING Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b). allowing deep submergence of the pump into the oil zone.

Jan 1, 1939

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984