Search Documents

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By D. B. McWhorter, J. D. Nelson

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1981

By M. J. Swan, W. C. Foshee, R. R. Klimpel

The large volume of water used in coal preparation plants makes water recycling a necessity. Economical cleaning of dirty water usually requires flocculation with an efficient organic polyelectrolyte. This paper discusses identification of optimum flocculant systems. Supporting laboratory data with on-site tests and full-scale field trails supplies information necessary for matching the polymer to the plant.

Jan 1, 1983

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 ('other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By Charles R. Simcoe

The stress-strain curves in the microyield region for various Fe-C solid solutions shown by Davies and Ku are typical examples of parabolic curves defined by the expression a = kEn 111 These data, when replotted on log-log coordinates, as shown in Fig. 9, exhibit three essentially parallel straight lines. It is apparent that carbon increases the flow stresses, but does not affect the exponent n. In other words, the only factor in Eq. [1] affected by in in carbon content is the constant k. As Eq. [1] is written k is the stress at a strain of 1.0. This is unsatisfactory for examining data in the microyield region. Therefore, the equation can be altered to the form: to permit the use of the authors' microyield stress at a strain of 10-6 as k. Extrapolating the curves in Fig. 9 to a strain of 10-6 gives stress values of 2000, 3200, and 5400 psi for 0.008, 0.014, and 0.02 pct C, respectively. These values do not agree exactly with the authors' measured values, but this will not affect the following discussion. The effect of carbon content on the slopes of the stress-strain curves shown in Fig. 2 of the paper by Davies and Ku can be analyzed by differentiating Eq. [2] with respect to strain. Thus: where n is always less than 1.0. Since n is essen- tially constant as a function of carbon content for the data under discussion, the slopes of the stress-strain curves depend only on k and E. If the slopes are examined at various selected Plastic strains. i.e., 10-6, 10-5, and so forth, it follows from Eq. [3] that the dif-ferent slopes for the different carbon contents depend only on the different values of ke=10-6. Thus, the larger ke=10-6, the steeper the linear stress-strain curve will rise with increasing plastic strain. This

Jan 1, 1969

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.'-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.'-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

By D. Turnbull, A. M. Turkalo

It is well known that if copper that has been severely cold-worked by rolling (70-98 pct) is heated to high temperatures a small number of large grains are formed at the expense of the fine grained structure that appears upon primary recrystallization. Dahl and Pawlek,' Cook and Mac-Quarie,2 Ward,3 and Boas and Bowles4 have studied this phenomenon in copper. It has been reported as taking place with measurable velocities in the temperature range 700-1080". Boas and Bowles have reported that the time necessary for the transformation is of the order of days at 700°C. According to Ward3 the number of secondary grains which appear in OFHC copper decrease with increasing perfection of cubical alignment after primary recrystallization; also the perfection of cubical alignment increases with decreasing grain size prior to the final reduction. In this investigation two heats, A and B, of especially high purity copper (99.999 pct) supplied by the American Smelting and Refining Co., were used. The behavior of samples prepared from the two heats was qualitatively very similar providing that the grain sizes established prior to the final reduction were about the same. We observed that in specimens prepared from bars which were relatively coarse grained prior to final reduction secondary recrystallization took place at a rapid rate at temperatures as low as 500°C. This is about 200-300°C lower than the temperature necessary to obtain fairly rapid transformation in OFHC copper. A 0.22 in. thick rectangular bar of lot B was cold-reduced 60 pct by straight rolling and given a penultimate annealing treatment at 250°C. Following this it was cold-reduced 90 pct and heated to various temperatures in the range 450-1040°C. The specimens were about 8 mils thick

Jan 1, 1950

By J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. -- Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing.

Jan 6, 1953

By Jack L. Lytton, Oleg D. Sherby

RESULTS of recent investigations1 on the creep of metals at high temperatures have revealed that the activation energies for creep of pure metals, AH,., about equals the respective activation energies for self-diffusion, hHD. This fact strongly suggests that the rate-controlling process in creep at high temperatures might be that of dislocation climb, as first postulated by Mott.' It would be desirable, however, to relate the creep rate of a metal at a given temperature and stress with actual diffusivity data, rather than with a comparison of the tempera-

Jan 1, 1957

By C. W. Carpenter, P. T. Bail, J. E. Bobek

This paper presents the results of model studies made to demonstrate the validity of applying the "basic" waterflooding scaling relationships of Rapoport1 to water-wet reservoirs composed of communicating strata of different permeability. Results demonstrate that these relationships can be validly applied, and also show the combined effect of variables on recovery. This demonstration was needed to confirm that the sizable effects of communicating strata on waterflood behavior, observed in model studies, were actually representative of field behavior. INTRODUCTION Rapoport1 Collins2 and others have presented scaling laws for modeling water-oil displacements. The validity of these laws has been experimentally demonstrated for homogeneous systems only. Recently, however, several investigators have presented the results of multilayer model studies made to determine the effects of viscous, capillary and gravitational forces on oil recovery in systems composed of communicating layers of different permeability. Dyes and Braun,3 using miscible displacements to simulate water flooding, showed that vertical communication adversely affects recovery at unfavorable viscosity ratios in the absence of capillarity. Ogandzhanyants and Egorova, 4 Gaucher and Lindley,5 and Richardson and Perkins6 modeled water-oil displacements in layered systems using immiscible fluids with capillary forces present. These investigators found more efficient behavior than in the miscible system of Dyes and Braun. However, since the scaling laws had not been verified for heterogeneous systems prior to or during these tests, it was necessary to assume that the results were representative of field behavior. This report presents the results of model studies made at Jersey Production Research Co. to find out if the waterflooding scaling relationships are valid when applied to water-oil displacements in heterogeneous reservoirs with vertical communication. Data obtained in the study show the combined effects of viscous, capillary and gravitational forces on oil-recovery behavior. The studies were performed in strongly water-wet systems where strong imbibition forces were present. For systems of different wettability, the effects of capillary imbibition would be somewhat different than those presented. APPROACH The scaling laws studied were those developed by Rapoport1 and designated by him as "basic" scaling laws. These relationships require that the model be scaled to the geometry of the prototype, and that the model and prototype be operated at the same viscosity ratio and have identical relative permeability curves, contact angles and boundary conditions. It is also necessary that the groups** be identical in the two systems, although any of the parameters making up the groups may be different. Finally, the capillary pressure of one system must be directly proportional to that of the second. Studies were conducted in two four-layer models, representing quadrants of five-spots, which were geometrically similar and which had the same glass-bead packing. The fluids used assured the same wettability in both models. Thus, the contact angles and relative permeabilities of comparative sand layers in the two models were identical and the capillary pressures were directly proportional. However, one model had a characteristic length three times that of the other. To make the scaling groups equal and to check the scaling laws, it was necessary to adjust the rate, water-viscosity level, interfacial tension and water-oil density difference to compensate for the difference in model sizes.

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By J. B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals. However, any curriculum that does not provide background in such basis subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to use geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors. He may also be faced with legal, social, and political problems in land use, zoning, envil.onmenta1 protection, and reclamation.

Jan 1, 1985

By John F. Abel

At the spring meeting of the Open Pit Division of AIME's Arizona Section, I was asked a question which indicates the acceleration of technical advancement. The question was: "How does an engineer at a properly keep abreast of what is new?" The fact that some 200 Arizona AIME members were at the meeting is a testimonial to the desire of these men to do just that- keep abreast. There is a great deal of talk in academic circles about the built-in obsolescence of an engineering or scientific education, too. About 100 commencement speakers every spring are sure to admonish the graduates that education is a continuing thing. Mining engineers are a small fraternity. We keep informed by talking to one another. Talking shop is valuable but there is no substitute for reading.

Jan 1, 1970

By P. Somasundaran, Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. To develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase, and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in oleate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to enhance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface Properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1983

By R. Maddin, N. Ujiiye

ALTHOUGH the cold-rolled texture for body-centered-cubic metals and alloys is well known (see, e.g., Barrett'), the pole figure representing the texture may be interpreted in two ways. It may be regarded as consisting of several ideal preferred orientations with an associated spread (a view which is shared among several investigators2), or it may be regarded as consisting of two sets of continuous preferred orientation also with an associated spread."." Recently, Chen and Maddin7 noted a stable (001) [loo] end orientation for molybdenum single crystals rolled at low rates of reduction provided the initial rolling. orientation" was close to the cube ori-

Jan 1, 1957

Edgar Hall, Silverspur, Queensland, Australia (communication to the Secretary*):—Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the eide of freedom among the' younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms mentioned have suffered by their secrecy is their own business—I hold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to he proved conclusively by Dr. Douglas's own writings. In his paper on The Copper Situation,' Dr. Douglas says : "In comparing iron and copper mining,...it must be remembered that 2 tons of average iron ore from the most prolific source now available ... will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year's production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-orc would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Jan 1, 1909

Doctor David Yang has presented an important new flotation development in the area of fine particle flotation technology; at the same time Dr. Yang presents an explanation for the effectiveness of this improved new fine flotation system in terms of an optimum dispersion state. The same statement is made for the case of carrier flotation (ultraflotation), in the removal of anatase from kaolinite by addition of calcite (selective flocculation of the anatase - calcite system and dispersion of kaolinite). Dr. Yang's data and statements raise some important questions, and I will adress myself to the more fundamental aspects of this new flotation system. The addition of sodium silicate, well known as a good depressant-dispersant agent for siliceous gangue minerals, is proved to be greatly enhanced by the incorporation of polyvalent metal salts into sodium silicate prior to flotation, producing in this manner a condition, as described by Dr. Yang, of optimum dispersion, which in the case of fine-grained oxidized taconite can be described as selective flocculation (coagulation) of hematite and almost complete dispersion of siliceous gangue components. Dr. Yang recognizes that the main mechanism, while not completely understood at this time, seems to operate by modifying the surface characteristics of the gangue slime particles so as to prevent collector from bonding there to, and making the particles strongly hydrophilic so they will become fully dispersed and consequently will not float during froth flotation. At the same time it appears that the conditioning reagent also modified the surface characteristics of the floated minerals (hematite and spodumene in this case) so that they will aggregate and tend to more readily adsorb the collector, resulting in an improved flotation kinetics and selectivity.

Jan 1, 1979