Search Documents

By B. Mueller

Altered concepts regarding the raw material used in conventional blast furnace plants as well as new technologies for the reduction of iron ores make it necessary to reconsider the design of pelletizing plants. The incorporation of a pelletizing plant within a conventional integrated steel mill involves considerations of the problems of using in-plant fines. A modern pelletizing plant in Mexico serves as an example of the technical solution. In recent times, pelletizing plants are also being integrated within steel mills based upon direct reduction processes. The design of such pelletizing plants must take into account special product quality requirements.

Jan 1, 1977

By A. W. Dana, F. J. Shortsleeve, A. R. Troiano

The phenomenon of flake formation which may occur during cooling or room temperature aging of large steel sections is caused by a combination of hydrogen and stress. As such, the transformation characteristics of austenite in a particular section play a major role in the occurrence of flakes. Isothermal and continuous cooling studies demonstrated that flake formation is particularly sensitive to nature, distribution, and relative proportions of the microconstituents in the cooled sections. In the absence of transformation stresses, abnormally high hydrogen contents could be tolerated without flaking. Flakes were not found in the absence of transformation stresses. No correlation existed between average hydrogen content and flake formation where cooling stresses were low. Hydrogen in the steel was a necessary but not sufficient condition for flake formation. DESPITE a long history of laboratory and commercial investigations, the mechanics of hairline crack or flake formation in large steel sections remains unresolved. Recent publications1-5 emphasize that flaking is still a serious problem.* immediate cause of flaking is the pressure exerted by entrapped hydrogen gas that collects in small internal cavities or voids during cooling. When the temperature of steel is low enough to preclude extensive plastic flow, the cavity pressures cause local brittle fractures (flakes). 2—The microsegregation and transformation stress theory. According to this theory, flaking results from stresses arising from the volume changes accompanying the formation of martensite and/or low temperature bainite after a large portion of the section has transformed at elevated temperatures. The proponents of the hydrogen theory suggest that stresses from other sources may be additive to the stresses produced by hydrogen and may, in some cases, provide the increment of stress necessary to produce flakes. However, the critical aspect of this theory is that no stress, except that produced by hydrogen pressure, is believed to be sufficient in itself to produce flakes. For practical considerations, this means that the only safe thermal cycle is one that reduces the hydrogen content to some low critical level below which flaking will not occur regardless of the state of transformation. On the other hand, the transformation stress theory does not rule out the embrittling effect of hydrogen. This theory simply proposes that flaking does not occur in the absence of transformation stresses. With the transformation stress theory as a basis, commercial antiflaking cycles would be designed to complete the transformation of austenite prior to cooling to ambient temperatures. Both of these theories appear compatible with industrial experience. Antiflaking cycles, such as cooling at extremely conservative rates or soaking for periods of time in the upper subcritical temperature ranges prior to cooling to ambient temperatures, may allow the following: 1—diffusion of hydrogen out of the section and, as a consequence, reduction of the hydrogen content to some safe minimum value (hydrogen pressure theory) and 2—complete decomposition of the austenite at rela-

Jan 1, 1956

By William R. Patterson

ACCORDING to the phase diagram for the Mn-Ni system,' the high-temperature, fcc y-manganese solid solution is stabilized to below room temperature, in the range approximately 22 to 28 wt pct Ni. However, pearson2 cites evidence in the literature showing that for manganese contents greater than about 75 wt pct the quenched phase in Mn-Ni alloys is fct. This is in keeping with zener's3 suggestion that in manganese-rich alloys the fcc high-temperature phase undergoes a diffusionless or martensitic transformation to a fct structure upon quenching. Work by Basinski and christian4 on manganese-rich compositions in the similar alloy system Mn-Cu established that in alloys of greater than about 82 wt pct Mn the y-manganese phase underwent a fee fct martensitic transformation upon quenching to room temperature. Striking evidence for this martensitic transformation was the highly twinned or banded microstructure, an example of which is shown in Fig. 1. Similar microstructures have also been found in quenched Mn-Cr5 and Mn-Au6 alloys. In the present investigation, we attempted to obtain similar evidence of a fcc — fct martensitic transformation in manganese-rich Mn-Ni alloys. Manganese alloys in the range 10 to 30 wt pct Ni were prepared by arc-melting, under argon, at atmospheric pressure. The alloys all were 50 g in size, and negligible weight loss occurred during melting. The starting materials were electrolytic manganese and nickel, both of 99.9+ pct purity. The alloys were subsequently homogenized 48 hr at 1750°F, hot-rolled 50 pct at 1700°F, annealed 2 hr at 1700°F, and water-quenched to room temperature. All heat treatment was done in purified argon. Both X-ray and metallographic techniques were used to examine the structures of the quenched alloys. X-ray diffractometer studies were conducted on powder specimens obtained from filings rean-nealed 2 hr at 1700°F in argon and water-quenched. Identification of the intensity peaks from the diffractometer counter traces showed that below about 10 to 12 pct Ni the y phase decomposed partially upon quenching to give an a- + ?-manganese structure. In the range approximately 12 to 25 pct Ni, the structure was found to be fct ? manganese with a c/a ratio approaching 1.0 at 25 pct Ni. Beyond approximately 25 pct Ni, the structure remained fcc. These results, including lattice-parameter determinations, are given in Table I. Metallographic examination. was carried out on specimens polished and etched after quenching, and also on polished specimens reannealed and quenched. In the first case, the distinctive twinning or banding so prevalent in Mn-Cu alloys was sought, while in the second, the surface relief effect generally regarded as being truly characteristic of a martensitic transformation was sought. The microstructure of representative alloys in the range 12 to 25 pct Ni is shown in Fig. 2. The structure of the Mn-15 pct Ni

Jan 1, 1965

By Edwin F. Brush, John Chipman

Published data on the activity of carbon in binary and ternary austenite at 1000°C are reviewed. The composition variables are . The coefficient, Vj, has the value for substitutional elements but may be assigned a ualue -1 for silicon to effect a simplification on the mathematical treatment. The activity coefficient PC = is obtained from gas equilibrium data. For the ternary systems studied the Henrian activity coefficient is given by the expression: The principle advantage in cornparison with the analogous expression in terms of atom fractions is found in the fact that for most systems the final term and in many the last two terms are zero. Values of the interaction parameters are tabulated and the graphical comparison of the equation with experirt~ental data is sho,wn in several figures. The thermodynamic properties of the solid solution, austenite, are of considerable importance in the heat-treatment of alloy steels and in other aspects of ferrous metallurgy. Early studies embodied in the Fe-C diagram have been extended to include other binary and some ternary diagrams. Our best hope of obtaining a useful thermodynamic treatment of reactions in complex alloy steels will not be found in quaternary and quinternary phase diagrams but in determinations of activities and interaction relations among the several solute elements. The foundation for such a development was laid by smith' in his early studies of the activity of carbon in Fe-C alloys and his subsequent work on Fe-C-Si, Fe-C-Mn, Fe-C-Ni, and Fe-C-Co solid solutions.2"4 Other observers have also made noteworthy contributions and these will be discussed and correlated here in the light of a somewhat simplified mathematical treatment of solute interactions. Fe-C AT 1000°C In a recent review of the thermodynamic properties of binary Fe-C austenite it was shown that the simple mathematical treatment employed by smith' was capable of describing all the published results on this solution. The treatment utilizes the atom ratio, yc = nC/nF,, rather than the atom fraction. The activity of carbon is proportional to the equilibrium gas ratio, either measured on a scalk in which the activity of graphite is taken as unity or, alternatively, aC may be set equal to yc at infinite dilution. In either case the ratio aC/y = (PC, the activity coefficient. It was found that the experimental data of smith1 and those of Diin-wald and wagner; Bungardt, Preisendanz, and Lehn-ert,' and Scheil, Schmidt, and Wiinnings at temperatures of 800" to 1200° C as well as reliable data on the solubilities of graphite and cementite could be represented by the equation for which graphite is the standard state: The data on alloyed austenite have been obtained at 1000°C. For this temperature, the "Henrian" activity coefficient (which is unity at infinite dilution) is: FOr an interstitial solute such as carbon in austenite it has been shown by statistical mechanicsg that the activity in the infinitely dilute solution is proportional to the ratio of the number of lattice sites occupied by carbon to the number of yet unfilled lattice sites. A variable zz proportional to this ratio serves as a useful measure of concentration:" in which b is the number of lattice sites provided by each atom of solvent; in austenite b = 1. The Henrian activity approaches zz at infinite dilution and the ratio a is the activity coefficient. The effect of a change in concentration is then given by: It has been shown further that in some systems the derivative in Eq. [4] remains constant over a wide range of concentrations. In such a case second-order terms become negligible and the Henrian activity coefficients is:

Jan 1, 1969

By E. W. Davis

If the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indications that this new process may make commercially possible the manufacture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to magnetite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red temperature in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900' F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1939

By E. W. Davis

If the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indications that this new process may make commercially possible the manufacture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to magnetite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red temperature in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900' F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1939

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By W. P. Sykes

In an earlier paper1 the composition-temperature limits of the gamma iron phase in the iron-tungsten system were reported as approximated by thermal analyses. At that time no attempt was made to develop metallographic evidence of the coexistence of two phases in the iron-rich solid solution at temperatures between 900" C. and 1400" C.

Jan 1, 1931

By Richard H. Rein, John Chipman

The activity of SiO2, in the entire liquid system SiO2-CaO-Mg0-A12O3 at 1600°C is calculated from the distribution of silicon between these slags and Fe-Si-C alloys saturated with either graphite or silicon carbide, the activity coefficient of silicon in these alloys, and the requisite thermodynamic data. The activities of the other components in the ternary systems SiO2-CaO-A12O3, SiO2-MgO-CaO, SiO2-MgO -A12O3 are computed from these data by the IrON blast-furnace slags can be regarded as consisting of the four major oxide components, SO2, CaO, MgO, and A12O3 along with minor proportions of other oxides and of sulfur. The purpose of this study is to measure the activity of silica in the liquid solutions of these four oxides at iron-making Gibbs-Duhem equation with the aid of the known free energies of several of the interoxide compounds and the accepted phase diagrams. Based on these activities, new data are Presented for the free energy of formation of a number of the interoxide compounds. The free energy of mixing the liquid metasilicates of CaO and MgO shows slight positive deviations from the ideal. temperatures and to obtain activities of the other components by application of the Gibbs-Duhem equation and the properties of several interoxide compounds. Recent investigations on the activity of silica in the SiO2-CaO-A12O3 system1-3 and recogntion of a serious error in older data for the free energy of formation of SiO2 (Ref. 4) have succeeded in bringing a fair degree of concordance into the results of different investigators. In the present study, the activity of silica is obtained from the silicon-distribution experiments described in a previous paper,' the revised activity coefficient of silicon

Jan 1, 1965

By M. W. Fabjanczyk, E. G. Alexander

INTRODUCTION The purpose of this paper is to summarise development of design processes used in the 1100 oreoody as a result of experience encountered. Design methods have been developed as a result of the history of ground behaviour, free-standing qualities of cemented back fill and mass blasting techniques. This paper contains an historical review of design methods previously described by Matthews ( 1972 ) , Hornsby and Sullivan (1977 and 19781, Kirkby, Blair and Hutton (19781, and Stewart (1980). The reasoning behind design philosphy changes are discussed and placed into context with methods now adopted. The 1100 orebody is Mount Isa's main producer of copper ore (5 million tonnes per year ) . Proven reserves are 120 million tonnes at 3.2% Cu. Location of the 1100 orebody in relation to overall mine geometry was well described by Dayton (1976). Geology The orebody is located in a series of massive brecciated shale lenses, in either a siliceous or dolomitic matrix, surrounded and separated by a uniform shale sequence. The whole formation is truncated at depth by a faulted contact with a greenschist facies metamorphic sequence below (Figure 1 and Figure 2) Mathias and Clark (1976). The breccia is known locally as silica dolomite and contains nearly all the economic mineralisation. Interfingering of shale and breccia often results in irregular boundaries to the silica dolomite and the ore limits. Geometry The geometry of the orebodies is shown by Figures 1, 2 and 3. Figure 3 also shows the location of the copper orebodies in relation to the lead orebodies. Structure Although the orebody is contained within the massive breccia (u.c.s. 150-250 MPa), it is cut by shear zones sub-parallel to the regional bedding (north-south striking, dipping approximately 60o to the west), and diagonally by major transverse faults (Figure A). These major faults have continuity in excess of 300 metres, with varying amounts of displacement up to 200 metres, and are zones of potential movement.

Jan 1, 1981

By W. A. Schaeffer, Sidney A. Justin, Jr. H. D. Easton

Restriction and proration of petroleum production have increased materially the difficulties attendant upon the estimation of reserves, particularly in large, "flush" fields. Such practices preclude the use of decline or other curves, from which, under capacity production conditions formerly prevalent, much could be learned as to the ultimate recovery to be expected from a given field or lcase therein. In restricted fields that would produce at many times the low rate allowed by the regulations in force if allowed to flow without restraint, one is forced to use other information than production performance to predict the volume of oil recoverable. Examples are: at Kettleman Hills, California; the Conroc, Van and East Texas fields, Texas; the Iowa field, Louisiana. It is beyond the scope of this paper to apply a definite method to the determination of the reserves in any actual field, therefore the discussion will be limited to a consideration of available methods and an enumeration of important factors governing the accuracy of such estimates. The problem is to determine not only oil in place but recoverable oil in place, for a given field or tract, which is complex and depends not only on the characteristics of the reservoir but also on the plan of development, the production allocation scheme, the rate of production and many other factors. Many data must necessarily be considered, weighed as to inportance, and assigned quantitative values. Estimates of recovery in prorated fields have been discussed by Brace', Shaw2, Snider3 and others. The wide difference in estimates of ultimate recovery from a number of important recently developed fields demonstrates the inadequacy of

Jan 1, 1935

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By T. L. McCall

The late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20". The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable outside advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By Thomas Fraser, H. F. Yancey

Prior to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pet of the total production of high-rank coal, the Saar and Aachen about 6 pet each, Upper Silesia about 14 pet, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany nest of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pet of the total energy requirement, brown coal supplied about 25 pet, and water power, wood, petroleum and alcohol together aggregated only 7 pet. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered eatraction of coal was enforced. Each lease comprised a relatively extensive area. which accounts for the generally large size of the mines and mining companies In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but 90 pet of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsen-kirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G. a State-owned company operating in the Saar, which produced 'lore than '3 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bitumillous coal and brown coal, but in 1938 some 44 million toils of brown-coal bri-

Jan 1, 1947

By Thomas Fraser, H. F. Yancey

Prior to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pet of the total production of high-rank coal, the Saar and Aachen about 6 pet each, Upper Silesia about 14 pet, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany nest of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pet of the total energy requirement, brown coal supplied about 25 pet, and water power, wood, petroleum and alcohol together aggregated only 7 pet. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered eatraction of coal was enforced. Each lease comprised a relatively extensive area. which accounts for the generally large size of the mines and mining companies In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but 90 pet of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsen-kirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G. a State-owned company operating in the Saar, which produced 'lore than '3 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bitumillous coal and brown coal, but in 1938 some 44 million toils of brown-coal bri-

Jan 1, 1947

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962