Search Documents

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objection- able to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for efficient hand picking. At most mines an attempt is made to remove the visual impurities at one or more of the following places in the surface plant? (1) in the tipple during screening; (a) on picking band, belt, or shaking conveyors;*(3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller

Jan 1, 1943

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By B. Ramaswami, Y. Nakada, U. F. Kocks

Compression tests were performed on single crystals of aluminum, silver, gold, and a Ag-10 pet Au alloy, with height-to-width ratios from 8:1 to 1:1. As this ratio decreased, so did the amount of easy glide until, for cubic specimens of all the pure materials, it was entirely absent. Heterogeneity of deformation is proposed to he a major contribution to the explanation of easy glide in slender specimens. For comparison, one single-crystal cube of zinc was tested and showed a behavior very similar to that in tension. Beyond easy glide, tension and compression curves are very similar. It is concluded that, in this range, neither grip effects nor orientation change influence the work-hardening characteristics to any significant extent. (121) and (100) crystals of all materials had similar stress-strain curves in tension and compression, except that the stress level of the flat portion of aluminum (109 crystals at high strains mas somewhat higher in compression. These results are at variance with previously proposed mechanisms of orientation dependence by both Hosford and Kocks. The compression tests themselves are described in detail and it is shown that they are essentially frictionless and produce single slip when the crystal is suitably oriented. DEFORMATION in uniaxial compression does not necessarily give the same result as deformation in uniaxial tension, essentially because the boundary conditions chosen are practically always different. 1) The shape and size of the specimens are usually different, and any genuine effect of size on work hardening should thus influence the result. 2) The grip constraints are usually different and can vary substantially for different kinds of tests. If the compression specimen is a thin plate and the friction on the platen is large, the grip contraints are more serious than in tension and lead, in the extreme, to uniaxial strain rather than uniaxial stress. If the specimen is roughly cubical and the friction is low, the specimen is less constrained than in tension inasmuch as displacements in the contact face are allowed. 3) The orientation change of single crystals is of opposite sign in tension and in compression; it is furthermore different in detail, because the relevant orientation in a squat specimen is the normal to the contact face, whereas that in a slender specimen is the generator of the side faces.' The considerable dependence of work hardening on the initial orientation in tension would suggest that the orientation change should also be very important. 4) Finally, localized deformation instabilities found in tension tests, such as necking and Lüders band propagation, are not possible in squat specimens. This is, for some investigations, a favorable consequence of the large grip influence. Even if one is not interested in any of the effects mentioned above, compression tests are often desirable just because the specimens needed are so much smaller and sturdier. For example, they have been very helpful in the investigation of latent hardening by means of alternate longitudinal and lateral compression of cubes,* and for testing

Jan 1, 1964

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is- and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result: Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobuses grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton

Jan 1, 1939

TWO recent developments in open hearth steelmaking have had a substantial impact on metallurgical practices and operating procedures. These are: (1) the use of oxygen roof lances for accelerating the refining reactions, and (2) the use of a spring-arch, basic roof for prolonging the life of the furnace. Although these practices can be used separately, they are generally used to complement each other in an effort to obtain minimum heat time consistent with an acceptable rate of wear of the refractory roof, walls and port ends. DECARBONIZATION BY OXYGEN INJECTION The use of oxygen to speed carbon elimination was perceived by Sir Henry Bessmer but its practical use in steelmaking could not be realized until processes were developed for the manufacture of low cost, tonnage oxygen. However, as early as 1922 Bigge1 obtained a patent covering the use of gaseous oxygen to speed decarbonization of a molten steel bath. At that time, oxygen was available only in bottles and at a cost of $240 per net ton. At the end of World War II the price of oxygen had dropped to $80 per net ton, and as a result, metallurgical oxygen (99.5 per cent began to come into widespread experimental use for decarbonization in open hearth and electric furnace shops.2-8 Even this price prevented oxygen's routine use for other than decarbonizing the bath in shops producing substantial quantities of steels containing less than 0.40 per cent carbon. Today, tonnage metallurgical oxygen can be manufactured for less than $15 per net ton, and commercial purity oxygen (95 per cent is reported to cost less than $5 per ton. Thus, it is not at all surprising to find many open hearth shops effectively using large quantities of oxygen to accelerate decarbonization. Equipment for Oxygen Injection. The oxygen may be injected by a lance pipe inserted through the wicket hole and pushed several inches into the steel bath, or by a water-cooled jet inserted through the back- wall, endwall, or roof, and immersed in the slag or set just a few inches above the slag. Oxygen at approximately 100 psi is piped directly to control stations adjacent to each furnace. The installations should include adequate safety devices such as fire checks and emergency valves,

Jan 1, 1964

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By F. F. Poland

The purpose of this paper is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possiblc the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. Purpose of Development It was recognized early in the war effort that nickel would become a critical metal. therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elemcnts (maximum). 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the conversion was made successfully.

Jan 1, 1949

By L. L. Handy

Two equations are compared for calculating imbibi-tion rates of water into porous media. A linear relation was found to apply when the square of the volume of water imbibed was plotted against time for water imbibing in natural rock materials. The effect of adsorbed organic materials on surface wettability was determined from measurements of rate of imbibition, water saturation and water permeability. INTRODUCTION An understanding of the mechanisms by which water displaces oil from porous media requires an understanding of the role of capillary forces in the displacement process. The capillary forces are determined by properties of the water-oil-solid surfaces. Consequently, some measure of the surface properties of reservoir rocks is necessary if displacement behavior in oil reservoirs is to be predicted from laboratory measurements. Several experimental procedures have been proposed to assign quantitative wettability indexes to reservoir rock surfaces. The most recent of these proposals are those of Bobek, Mattox and Denekas&apos; and Amott.&apos; These indexes are designed to show a continuous variation from the preferential oil-wet to the preferential water-wet systems. They require measuring some property of the rock which is a function of surface wettability. The quantities are measured on unaltered core material and compared with values obtained for known oil-wet and water-wet extremes on the same material. These methods are useful but are semi-empirical in nature. They have the disadvantage that the measured quantities may be functions of other variables in addition to surface wettability. Some understanding of the behavior of water-oil-rock systems may be obtained from studies of the simpler water-air-rock systems. Surfaces of a given wettability are more easily maintained for the latter. Also, certain approximations can be made for the flow of water and air which are not justified for water-oil flow. The theoretical and experimental work discussed in this paper is part of a study of the role of capillarity in the dynamic displacement of air by water. The expec- tation is that observations for the water-air system will lead to generalizations which are applicable to water-oil systems. THEORY Imbibition is defined as that process by which one fluid displaces another from a porous medium as a result of capillary forces only. Differential equations have been derived to describe the displacement of oil by water during imbibition, but these equations have not been solved.".&apos; With certain assumptions, however, solutions are possible for water-air imbibition.

By C. W. Lawr

The ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, arc mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 Ib.) KCN per ton of solution. As the daily discharge to the dam was 1600 tons&apos; of slime of a 2:1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and it&apos;s recovery held alluring possibilities. Principle of Cyanide-recovery Process As it had acquired the patent rights to theLayng (H. R.) and Halvor-sen (A. L.) processes, also those of Mills (L. D.) and Crowe (T. B.) after considerable experimental work in its own laboratory and at Tonopah, Nev., The Merrill Company of San Francisco early in 1923 notified the Mexican Corporation and compania de Santa Gertrudis of its process for the recovery of cyanide from weak wash solutions, or for the transference of cyanide from a foul mill solution to a clean alkaline solution. This method is known as the Mills-Crowe process, the principle of which is as follows: The solution from which the cyanidc is to be removed is made acid by bringing it into contact with sulfur dioxide (SO2). The acidified solution is the; transferred to a closed tank in which air and solution are brought into intimate contact. The air leaving the tank charged with HCN is then passed to another tank in which it is mixed with an alkaline solution,

Jan 1, 1930

By B. H. Kear, S. M. Copley

A dynamic theory of precipitation hardening in alloys containing cohevenl, stvess-.free, ordered particles is developed. The yield stvess is predicted from the stress dependence of the plastic strain vale, which is related to a derived dislocation velocity-stress function. The theory is shown to predict the magnilude and temperature dependence of the yield stress of a commercial nickel-base superalloy as well as many details of its slip structure. GLEITER and Hornbogen have developed a theory of the yield stress in alloys hardened by coherent, stress-free ordered ptrticles based on the observation that dislocations (b = a/2 (110)) glide in pairs.&apos; When a dislocation pair shears through an ordered particle, the glide motion of the leading dislocation is impeded since it must create antiphase boundary (APB), whereas the motion of the trailing dislocation is assisted because it annihilates APB produced by the first one. Taking into account the APB energy, the size, and spacing of the particles, G-H predict the observed yielding behavior in Ni/18.8 Cr/6.2 A1 alloys composed of a matrix phase y &apos;(nickel-solid solution) and particles of y&apos; (basically Ni3A1). The G-H theory, as well as all previous theories of hardening by coherent ordered particles, do not include the details of dislocation motion; the present dynamic theory is an attempt to overcome this limitation. In the dynamic theory, the yield stress is predicted from the stress dependence of the plastic strain rate, which is related to a derived dislocation velocity-stress function. This function can be evaluated if the structure of the alloy, the APB energy of the ordered phase, and the characteristic drag or frictional stresses of the matrix and precipitate phases are known. The theory is shown to account for the observed temperature dependence of the yield stress in a commercial nickel-base superalloy. 1) NICKEL-BASE SUPERALLOYS Although their compositions are complex, the nickel-base superalloys have remarkably simple structures. A detailed examination of the commercial superalloy

Jan 1, 1968

By H. C. H. Darley

The influence of particle size and concentration on the development of chip hold-down pressure (CHDP) was studied in an apparatus designed to measure the change of filtration rate during the first second of the filtration process. CHDP is controlled by the "bridging" particles (i.e., particles in the 50 to 0.2 micron range), whereas filter loss is controlled by the colloid fraction. The results indicated that a fast drilling fluid with a low filter loss could be obtained if the concentration of bridging solids and the viscosity were kept very low. A novel group of drilling fluids, which we have named colloid emulsions, was developed to meet the above requirements. These colloid emulsions are made by dispersing art oleophilic colloid in oil and emulsifying about 5 per cent of this dispersion in water or a dense brine. Good results have been obtained in field trials with emulsions which use asphalt as the oleophilic colloid. INTRODUCTION In recent years it has been found that fast rates of penetration can be maintained in hard formations by using "clear" water as a drilling fluid. In some cases, however, water cannot be used because the very high down-hole filter loss creates various difficulties in drilling, in logging, or in producing the well. It then becomes necessary to "mud up", which results in a decrease in drilling rate. The reason that mud decreases drilling rates is a complex subject which has been well covered by such authors as Garnier and van Lingen, Cunningham and Eenink,&apos; and van Lingen.3 One of the principal factors involved is the tendency of the drilling fluid to develop a filter cake on the bottom of the hole. The pressure differential which develops across this filter cake opposes the action of the bit in dislodging chips from the rock. This pressure differential is referred to by Garnier and van Lingen&apos; as the chip hold-down pressure, which is denoted by the initials CHDP in this paper. The work described in this paper was undertaken to develop a drilling fluid which would minimize CHDP but which would still have a low filter loss—in other words, a fluid which would deposit a filter cake on the sides but would lay little or no filter cake on the bottom of the hole. EVALUATION OF CHDP EXPERIMENTAL Conditions governing the growth of filter cake on the sides of the hole are obviously different from those on the bottom of the hole. On the sides of the hole, cake will form continuously but at a decreasing rate, until eventually the rate of growth will equal the rate of cake erosion by the mud stream.&apos; On the bottom of the hole, each time a bit tooth dislodges a chip the cake is removed, a fresh rock surface is exposed, and the filtration process must start over again. Thus the CHDP is determined by the amount of cake which can form in the interval between successive tooth strikes at a particular spot, normally a fraction of a second. Our first step therefore was to study filtration rates over the first second or so of the filtration process. These tests were conducted in the simple type of dynamic filter cell shown in Figs. 1 and 2. In this cell the mud was filtered through a train of rock cores while rotating blades kept the mud flowing over the surface of the core. The procedure was to evacuate the cores to 0.05 mm of mercury, saturate with brine, and assemble in the holder under brine. The permeability of the core train was then determined. A plastic seal was placed on the face of the core train, and a rip cord was attached from the seal to one of the blades. At the start of the test, 500 psi was applied to the mud, and the meniscus in the capillary measuring tube was adjusted to zero. When the blades were started, t,he seal was ripped from the face of the core, and filtration began. The filtration rate was at first measured by photographing the advance of the meniscus in the capillary tube. Using

Jan 1, 1966

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By John Drew Ridge

For the early conservationists before the first decade of the twentieth century, conservation meant largely the planned preservation of water, forest, soil, and wildlife resources-renewable natural resources-through efficient use. Water was primarily thought of as a resource that must be kept available for humans to enjoy in a recreational sense and as a habitat for wild animals, birds, and fish. Little thought was given to conserving water for actual human or industrial needs. If industry entered the picture it was as an actual or potential polluter of water, which was the basic necessity for drinking and bathing and for outdoor recreation. Even the forests were only held worthy of conservation largely because they were areas in which wildlife could, or should, abound and in which human beings might find relief from the cares and problems of everyday life. Finally, the soil was to be preserved in its natural fertility through proper fertilization, cultivation, and crop rotation; in this the conservation program did enter the realm of the practical. For through soil conservation, the world was to be able to raise increasingly large crops of constantly improved organic foods which the steadily growing population of the earth was to need to survive and improve. Relatively little time, however, was spent on considering what profit the farmers of the world were to make from the scientific farming on which they were to embark. In short, the appeal of the early conservationist program was much the same as that of the entire era of Theodore Roosevelt of which it was a part; it was to the heart rather than to the mind; it was to emotion rather than to reason. Because of the way in which the problem was approached, conservation took on the character of a crusade rather than that of a practical plan for the betterment of man through economically sound methods of improving his environment and the uses he makes of it. Conservation had, then, all the advantages of a stirring appeal to the emotions, but it did not have the lasting results that would have been achieved by a program with a sound economic basis.

Jan 1, 1959