Search Documents

By E. C. Bitzer

The primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high- grade heavy sink product. It appears from this last work that the new separator has definite mechanical and metalluigical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator has required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent development of the inverted or closed-top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1949

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By A. M. Rahm

PROBABLY the majority of red brass sand castings are judged merely on the basis of outside appearance and the quality of machined surfaces. Many castings, however, must individually withstand a hydraulic or air-pressure test before being accepted as parts of more complicated machin-ery. Finally, there remains a comparatively small group of castings intended for uses of considerable responsibility where only the highest possible characteristics of the metal are acceptable, and for these specially cast test bars are required. The shape of the cast piece from which the test bar must be detached varies greatly from one country to another. The test bar as specified in the American Society for Testing Materials Specification B62-36 is widely used by the American foundry industry. The actual test piece is at the bottom of the cast block and has a riser about six times its mass. It is obvious that this test bar has an advantage over the actual casting. The latter rarely possesses a riser of as much as 30 per cent of its own weight and that riser cannot generally be located in so convenient a manner. Therefore, the characteristics of the test bar cannot possibly correspond to those of the casting itself. It must be taken into consideration that red brass if melted and cast in the best possible manner may show a tensile strength of 40,000 lb. per sq. in. with 35 per cent elongation in 2 in. Such a test bar would indicate that the metal was nearly perfect from the viewpoint of its gas and inclusion content. Barring some accidental defect, a casting cor-responding to such a test bar could be accepted as being quite sound. However, actual specifications do not demand such high characteristics; indeed, few specifications require over 30,000 lb. per sq. in. and 20 per cent elongation, while one Federal specification demands merely 27,000 lb. per sq. in. strength and 15 per cent elongation. It is obvious that

Jan 1, 1939

By Robert Davis Longyear

In diamond-drill work, a true sample consists of all the material cut by the bit—both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 1, 1923

By Norman Visnes

EARLY in 1954, as initial development of the Galena mine was being finished, plans for stoping operations became the foremost consideration of the operating management. The Galena is being operated under lease agreement with the owner, Vulcan Silver-Lead Corp. Started in 1947, the Galena is a deep level development of American Smelting & Refining Co. and Day Mines Inc. under the management of ASARCO, in the Coeur d'Alene mining district. Lead mineralization was found on the 3000 level in 1950. In 1953 development on the 3000 level disclosed a siderite vein, later known as the Silver vein, which contains commercial quantities of silver in Tetrahedrite. This vein was explored on the 2800 and 2400 levels and later on the 3400 level, the lowest in the mine. Work above the 2400 level to date has indicated that the vein dissipates to weak mineralization, and ore values are uncertain above the 2200 horizon.

Jan 1, 1957

By Robert Davis Longyear

In diamond-drill work, a true sample consists of all the material cut by the bit—both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 1, 1923

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

By W. B. Agocs

In August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model I1 total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey.

Nov 1, 1955

By R. P. Ehrlich, D. A. Dahlstrom

In the hydrometallurgical circuit, many phase separation steps are usually necessary. Typical steps are pregnant liquor - leach residue separation by counter- current decantation or continuous vacuum filtration, clarification of liquids prior to precipitation, ion exchange or solvent extraction, dewatering of final product, etc. The paper discusses the more recent advances in these areas and considers general operating parameters and cost factors. In addition, emphasis is placed on future needs because of the growing importance and necessity of hydrometallurgical processing of minerals.

Jan 1, 1973

By R. V. Smith, M. H. Cullender

Rigorous equations for calculating subsurface pres.tures in flowing and static gas wells, and pressures along horizontal pipelines are presented in this paper. These general equations, based on the mechanical encrgy balance, contain no assumptions regarding temperature and can be used with either straight-line or curved temperature gradients. The friction factors recommended in this report are based on an absolute roughness of 0.0006 in. Flow is always considered to he turbulent. Although these general flow equations are solved by numerical means, the methods are as convenient as many of those used today to calculate pressures in gas wells and pipelines. These numerical methods are illustrated for flowing and static columns of gas in wells and for flow in pipelines. The authors believe that the use of these methods will result in more accurately calculated pressures in gas wells and pipelines and that [he methods are more flexible than any in use at the present time. Also, the methods are easily adaptable to automatic computers. INTRODUCTION The problem of calculating subsurface pressures in gas wells and along flowing pipelines has been studied by many investigators with the results that two widely-used methods have been presented in technical literature. One approximates conditions in a gas well or pipeline by assuming that temperature and compressi- bility are constants tor the entire gas column. The other method assumes that temperature is constant at some average value but permits compressibility to vary with pressure at the constant temperature. While these approximations may be justified for relatively shallow and low-pressure wells, they become more and more unrealistic as the calculations are applied to the deeper high-pressure wells. In wells or pipelines where there is an appreciable change in temperature between the inlet and outlet ends of the flow string, it is equally as important to consider the change in compressibility with temperature as it is to consider the change with pressure. Consequently, the methods presented in this paper were developed to provide a workable procedure for calculating pressures in gas wells and pipelines which makes no assumptions regarding either temperature or compressibility. The friction factors recommended for use with the equations were the result of study of published literature and extensive experimental work with gas wells. The F,. values in Appendix IV which contain the friction factor are equivalent to an absolute roughness of 0.0006 in. as calculated by the Nikuradse equation. The absolute roughness of 0.0006 in. was previously published by Cullender and Binckley2 for gas wells; it is in agreement with 0.00065 in. of Smith, Dewees, and Williams1 for gas wells and 0.00065 in. of Baker and Swerdloff4 for pipelines; it is in reasonable agreement with 0.0007 in. reported by the Bureau of Mines and the American Gas Assn.5 for large transmission lines. However, any type of friction factors may be used in the equations by a change in the F, values in Appendix [V].

Jan 1, 1957

By A. G. H. Andersen

A FEW years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and silicon1,2 some information on microstructures and hardness, not incor-porated in the published work, was obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it. may have in connection with the constitution of the alloys.

Jan 1, 1937

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

Expect Labrador Iron Ore Shipments by 1954 Iron ore shipments from the Quebec-Labrador area are a "definite expectation" by late summer, 1954, according to William H. Durrell, general manager of the Iron Ore Company of Canada. About $120 million have been invested in the project, with a total of $200 million expected to be reached before a ton of ore is shipped, Mr. Durrell said. According to the general manager approximately 418 million tons of open pit highgrade ore have been proven in the project. Deposits lie several hundred miles north of the mouth of the St. Lawrence River in territory which was without transportation of any kind. Construction of a railroad from Seven Islands to Knob Lake, about 360 miles, is an important part of the development plan. The railroad will be the first to adopt complete roller bearing applications. Construction is on schedule with 215 miles of the route graded. Completion involves two tunnels through rock, one of almost half mile length, a 700-ft bridge and several smaller spans.

Jan 3, 1953

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By E. P. Polushkin

This work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility of determining the amount of the constituents without separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. Suppose Fig. 1 represents a part of a photomicrograph on which the total area of the black figures is to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively. This is also true for the whole area of the photomicrograph. Therefore, to determine the total areas of the black and white figures we must first find the proportion between the sums of the medians and then divide the area of the whole photomicrograph in the same proportion.

Jan 1, 1925

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By Price E. R.

The coal industry was beset with work stoppages and strikes throughout the year, and there was some loss in markets to oil and gas. These conditions, along with the mild decline in industrial activity, the steel strike, and the reduction in exports, contributed to an unfavorable year for the industry. All coal mines are working three days a week at the time of writing, and in estimating production for the year, it will be assumed that the mines will continue to work on that basis through December. Total production of bituminous coal in 1949 is estimated at 420 million tons, which is 179,518,229 tons under the production in 1948. Anthracite production is expected to reach 39,400,000 tons as compared with 57,139,948 tolls in 1948, a loss of 17,739,948 tons. Coal stocks, as of January 1, 1949, were 69,373,000 tons but at the end of the year will have dropped to approximately 22 million tons. Regardless of the difficulties during the current year, the industry has made substantial

Jan 1, 1950