Search Documents

THE Searles Lake orebody is located in the north- west corner of San Bernardino County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which differ in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor.

Jan 2, 1954

By Charles J. Haas

The effectiveness of rock bolts in resisting shear displacement along preexisting fracture surfaces or slip planes was determined in the laboratory with full-scale bolts and large-scale shear test equipment. The system variables were the type of bolt, orientation of bolt relative to shear surface, and normal pressure on the interface. Results showed that, in general, both conventional bolts and resin- grouted reinforcing bars significantly increase the shear resistance along a fracture or bedding plane when the average normal compressive stress on the plane is in the order of 25 psi and when the bolt is oriented such that it tends to lengthen as the shear progresses. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented such that they lose tension as shear displacement occurs added no shear resistance since the tension drops to zero at very small shear displacements.

Jan 1, 1977

By William Blauvelt

Tun technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localities, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons or 60 per cent. was beehive, and 22,-600,000 tons, or 40 per cent. was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per. annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here.

Jan 3, 1918

By Perry G. Harrison

The first autlientic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is. said to have worked out his process. Jacobil in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeS04 + (NH4)2SO4. Lenz2 described some properties of electrolytically precipitated iron. He used Klein's bath, FeS0, + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By George H. Ashley

It has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. Production and Value In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately. Pennsylvania Accurate figures are obtainable for Pennsylvania for recent years because recent reports of the Pellnsylvania Department of Mines show the production from each mine and the bed worked at each mine. For recent years, therefore, it is only necessary to list the mines working in the Pittsburgh bed and add up their production. The value was obtained by treating each county separately, applying the average price for the county to the production of Pittsburgh coal in that county. Unfortunately for great accuracy, while production figures for individual mines are available for many years, the name of the bed being

Jan 1, 1938

By George H. Ashley

It has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. Production and Value In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately. Pennsylvania Accurate figures are obtainable for Pennsylvania for recent years because recent reports of the Pellnsylvania Department of Mines show the production from each mine and the bed worked at each mine. For recent years, therefore, it is only necessary to list the mines working in the Pittsburgh bed and add up their production. The value was obtained by treating each county separately, applying the average price for the county to the production of Pittsburgh coal in that county. Unfortunately for great accuracy, while production figures for individual mines are available for many years, the name of the bed being

Jan 1, 1938

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By Frederick J. McGarry, Parviz F. Rad

Although tunneling machines have attained very high advance rates in medium-hard rocks, the need for frequent repairs has slowed their use in very hard rocks. Laser- assisted tunneling is expected to improve tunneling machine performance by improving either specific energy or amount and quality of muck. The beneficial effects of lasing are the initiation and growth of microcracks from differential thermal expansion of grains, and overall spalling in the vicinity of the lased area. Using a constant thrust rock cutting device with disk cutters, the effects of cutter geometry, cutter diameter, thrust, and speed variations on specific energy and muck were explored and the improvement in performance of disk cutters caused by lasing was evaluated. It was found that the improvement depends on beam power and density, beam speed, pattern of heating, and cutting pattern and procedure. A focused beam slightly offset from the cutter path gives the most improvement both when cutting on a smooth surface and when cutting in previously cut grooves.

Jan 1, 1971

By Benjamin C. Greene, H. Beecher Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water'' was generally accepted without too much concern for what was in

Jan 1, 1981

By J. F. Kemp

Introduction The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.1 The further remark may, however, be made that the

Jan 2, 1915

By P. C. Kapur

A principal first-order and a minor summation term contribute to the solution to the discretized batch-grinding equation when formulated in cumulative retained mode. Depending on the inter relations hips between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The irn-plications and advantages of the reduced grinding equations are briefly discussed. In many instances, the trajectory of the particle-size distribution in a batch mill may be extracted from a set of particle mass balance equations as follows

Jan 1, 1971

By C Gunther

A preceding paragraph treats of the irregular manner in which ore deposits occur and the complex factors that control their distribution; the occurrence of metals in oreshoots in individual deposits is equally irregular, and the factors that control such segregation are equally complex. While the dimen¬sions of oreshoots in individual deposits may not be foretold with any degree of accuracy, the occurrence of ore in shoots is not accidental, but is controlled by laws some of which are understood. Any one familiar with permutations and combina¬tions who stops to consider the variety of factors that control ore deposition, and their varying relative importance, will admit that the science of economic geology must advance greatly before the occurrence of oreshoots may be predicted accurately in advance of exploration. The segregation of minerals in any oreshoot must be referred to some condition, or combination of conditions, local to the oreshoot as compared with the remainder of the deposit of low¬grade or barren minerals. Among the localizing factors that have been recognized are, in filled fissures, the amount and distribution of open spaces available for ore deposition, and in replacement deposits, the degree of brecciation giving access to the replacing solutions; the intersection of veins with other veins, dikes, sheeted zones, or porous strata; the impounding of solutions by impervious strata; and the differing precipitative influences of enclosing rocks. A large proportion of important and well ¬defined oreshoots, especially in deposits of deep-seated origin, are not assignable to any of these factors. While a knowledge of the character of oreshoots in general is important, a knowledge of the behavior of the known oreshoots

Jan 1, 1932

By Richard Franchot

IN the inevitable conquest of the blast furnace by metallurgical science in the solution of the problem of how to make more and better iron or to burn less coke, or both, it is highly desirable first to find out why the efficiency of the furnace generally is no better than it is. The immediate need would seem to be a theory to account for the existing facts. Explanation for the quantitative results obtained in current practice has been strangely lacking. One reason for this may be found perhaps in the custom of think-ing of efficiency in terms of coke consumption. Before efficiency can be explained there should be a fairly exact knowledge of what it is. A statement of the pounds of coke used per ton of iron made may have value in indicating comparative results in smelting similar ores with similar cokes, but it tells very little of the efficiency of the operation. When the materials are different, one practice burning 1800 lb. may be less efficient than another using 2000 lb. A better measure is the pig and slag per unit of coke. What is needed is a specific description of efficiency as a' definite quantity having an exact meaning. Such description is afforded by expressing efficiencies in terms of the respective proportions of the fuel energy absorbed in and chargeable to the various actions known to be -taking place in the furnace. Concretely, the energy value of a pound of coke having 85 per cent carbon blown with air heated to 1200° F. is about 7650 lb.-cal. (13,770 B.t.u.). And the work done in smelting a pound of average iron from hematite, comprising reduction and melting with production of a half pound of free running slag from an equal weight of limestone,

Jan 9, 1926

By Reynold Q. Shotts

CHEMICAL methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods5, 6on duplicate samples of the same coals, but to the author's knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published." This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation. By nitric oxidation samples of two whole coals were carefully analyzed for fusain, bright coal, and dull coal. One coal was analyzed in duplicate. Duplicate portions of each of the coals were divided into three density fractions by means of heavy liquids. A duplicate portion of one of the coals was divided by sieving into three size fractions. Each fraction was analyzed by oxidation and its percentage composition calculated in terms of fusain, bright coal, and dull coal. Because the weight percent of each fraction was known, a material balance calculation for the whole coal was also made. The resulting reconstituted analysis of the whole coal could be compared to that determined by direct analysis. In addition, specific reaction rate constants were determined for each component and for each whole coal or fraction. Arbitrary reactivity indexes were calculated by dividing by 100 the sum of the products of the percent of each component in the coal and its specific reaction rate constant. The resulting figure was an average reactivity index for each coal or fraction. Weighting the reactivity indexes for each fraction by the percent of the fraction in the coal gave a reactivity index for each whole coal which could be compared to that calculated directly from the whole coal analysis. If oxidation analyses really delineate definite physical entities within the coal, or even definite groups of similar entities, reconstituted analyses calculated from fraction analyses should check closely those made of the whole coal. It probably is true that optical methods identify and describe a greater variety of components than do chemical methods and that variations are wide in the appearance and quantity of those components identified optically. Chemical methods based upon differences in oxidation reaction rates would of necessity be less discriminating, as between similar components, than would optical methods. The procedures followed for oxidizing the samples, analyzing the residues, plotting and calculating the percentage of each component, and calculating its specific reaction rate constant have been fully described.'-' In brief the method originally proposed by Fuchs et al.1 for the determination of fusain consists of the oxidation of small samples of coal in boiling 8N nitric acid in a condenser-fitted flask. After boiling for periods of 1/2 to 4 hr, the unoxidized residue is filtered and washed. The washed residue is treated with normal sodium hydroxide, diluted, and allowed to stand for several hours. The resulting brown liquor is removed, and the filtered residue dried, weighed, ignited, and weighed again. The ash-free residue is expressed as a percent of original dry, ash-free coal. The percent residue is plotted against time, and the extrapolation of this line to zero time gives the percentage of dry ash-free fusain present in the original sample. The shape of the resulting time plots has been explained' by the assumption that they are the result of two different types of reaction, the first part representing a first order reaction with rate a func-

Jan 1, 1956

By H. M. Chance

The great outspread of the coal measures over portions of thirtyone of the sixty-seven counties of Pennsylvania, and the large number of workable seamy comprising the coal series,—together with some workable seams lately shown to belong to the (so-called) barren measures,—-create the impression that these fields contain a practically inexhaustible supply of fucl, and those who have estimated or attempted to estimate their available tonnage have generally promulgated this view. But the actual total contents of this coal-field is of no importance to us at present; calculations including all seams, whether thick enough to mine or not, whether pure enough to furnish a marketable fuel or not, whether accessible at reasonable depth or not, are of no practical value. As coal producers, we are interested not in the total contents, but in the total amount of easily accessible coal of good quality contained in beds thick enough for remunerative mining. The estimates contained in this payer refer exclusively to workable and accessible coal of commercial value,—we may call it available" coal. I am not aware that any one has as yet attempted to estimate in

Jan 1, 1882

By H. M. Chance

THE great outspread of the coal measures over portions of thirty-one of the sixty-seven counties Of Pennsylvania, and the large number of workable seams comprising the coal series, together with some workable seams lately shown to belong to the (so-called) barren measures, create the impression that these fields contain a practically inexhaustible supply of fuel, and those who have estimated or attempted to estimate their available tonnage have generally promulgated this view. But the actual total contents of this coal-field is of no importance to us at present; calculations including all seams, whether thick enough to mine or not, whether pure enough to furnish a marketable fuel or not, whether accessible at reasonable depth or not, are of no practical value. As coal producers, we are interested not in the total contents, but in the total amount of easily accessible coal of good quality con-tained in beds thick enough for remunerative mining. The estimates contained in this paper refer exclusively to workable and accessible coal of commercial value, we may call it "available" coral. I am not aware, that any one has as yet attempted to estimate in

Jan 1, 1882

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949