Search Documents

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By Robert M. Yonco, Irving Johnson, Martin G. Chasanov

The thermodynamics of the cadmium-rich portion of the Pu-Cd system has been studied with a high-temperature galvanic-cell method. The partial phase diagram of the Pu-Cd system was determined. The existence of the intermediate phases PuCd11 (cubic BaHg11 structure, ao= 9.282) and PuCd6 (cubic, CeCd6 structure, a, = 15.59) was established. The existence of at least one other intermediate phase richer in plutonium was indicated. PuCd11 was found to peritectically decompose into PuCd6 and liquid at 406" * 2°C. The solubility of plutonium in liquid cadmium may be represented by the equations: (355' to 399°C) log (at. pct Pu) = 6.223 -4282T-1 (399° to 632°C) log (al. pct Pu) - 5.148 - 5277T-1 > 1.156 x 106 T-2 The free energy of formation values (kcal per mole) of the two intermetallic phases are given by the equations: (PuCd11), ?Gf= -45.9 + 35.7 x 10-3 T (PuCd6), ?Gf0- -39.27 + 25.86 X 10-3T The excess free energy (kcal per mole) of plutonium in liquid cadmium may be represented by the equation: -(-16.72 * 29.54 NPu) 10-3T in which Npu and Ned are the atom fractions of plutonium and cadmium. The thermodyanamics of the U- Cd and Pu-Cd systems are compared. THERMODYNAMIC information on systems of the actinide metals with low-melting metals, such as zinc and cadmium, is useful in the design of pyro-metallurgical processes for the purification of nuclear reactor fuels. The thermodynamics of the Pu-Zn,1 Th-Zn.2,3 U-Zn,4-5 and U-Cd6 systems have been reported. The present report on the Pu-Cd system concerns the liquidus composition in the cadmium-rich region, the characterization of the two most cadmium-rich intermetallic phases, and the thermodynamic properties of these intermetallic phases and dilute liquid solutions of plutonium in cadmium. EXPERIMENTAL Phase Studies. The liquidus composition was determined by analysis of filtered samples of the liquid phase withdrawn at a series of temperatures. The apparatus and procedure were identical to that used in the previous study of the Pu-Zn system.' Briefly. a sample of the melt was withdrawn into a tantalum tube fitted with a porous tantalum filter (30-µ pore). the entire sample dissolved in hydrochloric acid (to avoid errors due to segregation

Jan 1, 1965

By L. M. Barker

The New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. History Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper. Geology Description of the geology of the Ajo district has been published by Ira B. Joralemon5 and by James Gilluly.6 The ore occurs chiefly in the porphyritic facies of Cornelia quartz monzonite, though appreciable

Jan 1, 1939

By L. M. Barker

The New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. History Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper. Geology Description of the geology of the Ajo district has been published by Ira B. Joralemon5 and by James Gilluly.6 The ore occurs chiefly in the porphyritic facies of Cornelia quartz monzonite, though appreciable

Jan 1, 1939

By J. A. Jr. Church

I. EARLY FURNACES. . COPPER blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18, ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By W. R. Ingalls

IN THE years immediately preceding 1914, the American people earned an aggregate income of 33 to 34 billion dollars, of which they saved about five billion, the annual saving being expressed mainly in the form of houses and railway extensions; to a less extent in public utilities, public improvements, factories and mines; and to a very small extent in foreign investments. It appeared needful that we should save and invest annually in these ways about 15 per cent. of our aggregate income in order to keep the development of our plant, so to speak, ahead of our steadily growing needs. The common knowledge that at present our housing and railway facilities are inadequate suggests immedi-ately that we have been running behind the pre-war ratio of reinvestment. Since 1919, we have not had any carefully prepared, authoritative estimates of the national annual income. However, with some experience in this subject, I have ventured to make rough estimates, which rest on solid foundations, although some rather empirical develop-ments are involved. Such estimates would be consid-ered good work in this field if they fell within limits of 10 per cent., plus or minus. Even so, these data are more useful when quickly available than more accurate data that are belated; for recognizing that there is a margin of error we can at least get a reasonable and approximate idea of how things are going.

Jan 2, 1923

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By Comfort Adams

WHEN this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. The then chairman of the Engineering Division of the National Research Council, Doctor Howe, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority' of the members of the committee. To that end, the Engineering Division appointed-a committee, consisting of the gentlemen whose names follow, to mention only those who retained their connection with it. At, this time there were serious difficulties in the manufacture for the Government, of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted.

Jan 1, 1922

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.' The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By John L. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product ; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are: 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson's ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young's modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott's work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger's single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By Lewis Stockett

During the year 1903, a building having machinery corresponding to ail anthracite-coal breaker was erected at the town of Stockett, Cascade county, Mont., for the purpose of breaking-up and cleaning bituminous coal. The coal is mined from a vein of the Kootenai group of the Lower Cretaceous measures having the following section: The vein is nearly horizontal in position, and each bench differs in quality as shown in Table I.

Jan 1, 1905

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922