Search Documents

By D. P. Kedzie, R. A. Dodd

The fatigue strength, fatigue hardening, and effect of fatigue deformation on subsequent age hardening of supersaturated Al(Cu) solid solutions have been determined as functions of alloy composition and temperature. The fatigue strength/tensile strength ratios, determined at 150°, 25°, and -195°C, decreased with increase in alloy content for all temperatures, but the F.S./U.T.S. ratios at -195°C decreased much more rapidly than did the ratios for 150" and 25°C. This suggested that strain aging and/or age hardening occurred during tests at higher temperatures. Additionally, the F.S./U.T.S. ratios at 150°C exceeded those at 25°C for all compositions, indicating greater strengthening during fatigue at 150°C. The effect of fatigue or tensile deformation at 150°, 25°, and -195°C on subsequent age hardening showed that the deformatzon increased the rate of precipitation and indicated that mechanically produced vacancies were probably formed during deformation. Fatigue hardening was studied at 150°, 25°, and -195°C, and the effect of room-temperature rests after 10 and 100 cycles was examined. The results confirmed that strain aging occurred at the higher temperatures . DURING the last 15 years various mechanisms of fatigue crack nucleation and growth based on dislocation and vacancy interactions, operating singly or collectively, have been proposed. The probable consensus of present opinion is that the fatigue process in pure metals essentially involves dislocation interactions, and that vacancies formed by such interactions play a minor or inconsequential role. However, there is some evidence that age-hardened alloys tend to overage during fatigue, probably by local vacancy-enhanced diffusion, and strain aging also might be important in selected cases. Furthermore, it has been established that the behavior of quenched-in vacancies in Al(Cu) and other solid solutions is composition-sensitive. Therefore, it seemed worthwhile to investigate various aspects of the fatigue behavior of supersaturated Al(Cu) alloys and to examine the results in terms of vacancy-enhanced effects. EXPERIMENTAL The alloys used in this investigation were prepared from 99.994 wt pet A1 and OFHC copper, the latter containing 0.04 pet 0 as the principal impurity. Six alloys were made, containing, by actual analysis, 0.58, 0.96, 1.96, 2.85, 4.45, and 5.51 wt pet Cu. They were induction-melted in air in graphite crucibles, cast as 7-in. by 7/8-in.-diam rods in graphite molds, and hot-rolled to 5/8 in. diam. The experimental work was a three-part program involving the determination of a) 10' cycle fatigue stresses as a function of alloy composition and temperature; b) the effect of fatigue deformation on subsequent aging of the supersaturated alloys; and c) fatigue hardening as a function of alloy composition and temperature. For determining the 105 cycle fatigue stresses, a portion of the 5/8-in. stock was machined into Krouse rotating cantilever beam fatigue specimens, 2 in. in length by 1/4 in. minimum diameter. These were tested at +150°, 25°, and -195°C (liquid nitrogen) on a Krouse high-speed machine, with special weights to provide lower -than-normal loading ranges, this being necessitated by the small load requirements of those alloys of lower copper content. For the high-temperature tests a small resistance heater was designed to clear the collets and fit in between the chucks, while for the low-temperature tests a hollow nylon cylinder was used, having closed ends drilled to pass a fatigue specimen, and positioned similarly to the heater. A plexiglass container completely enclosed the fatigue machine; rubber gloves fixed to ports in the walls enabled the machine to be operated from outside the box. A tray of magnesium perchlorate dried the air in the container and prevented both atmospheric corrosion fatigue at room and elevated temperatures and troublesome ice build-up at low temperatures. A total of ten to fifteen specimens was used for each combination of alloy composition and temperature. The result of each test was plotted on a standard S-N diagram, and the next stress was selected on the basis of the trends indicated by previous specimens. In this manner a small portion of the S-N diagram was constructed, and the 105 cycle fatigue stress obtained. Small Krouse fatigue specimens were also used to study the effect of cyclic prestrain on subsequent

Jan 1, 1964

By Albert R. Ledoux

In Great Britain all analytical chemists are styled assayers, but in the United states a slight distinction is made, assayers being considered those analytical chemists who have chiefly to do with the determination of the precious metals. There have grown up around the assayers of precious metals a number of customs and traditions which, as a rule, do not fetter American chemists when called upon to determine the composition or constituents of any samples submitted to them for analysis. In Great Britain, on the other hand, trade-customs even go to the extent of enforcing the employment of an admittedly erroneous atomic weight in certain alkali-determinations. If the American chemist is asked to determine the amount of lime in a water, potash in an alkali, or silica in an ore, the owner of the sample does not presume to suggest what method he shall employ, nor does he question his report on the ground that he should employ another method. But even in America it is different with the assayer. Unfortunately for the guild, as well as for those who have to base business operations on the reports of assayers, customs and traditions as well as divergent interests seek to circumscribe him in his choice of method and sometimes dictate how he shall perform his operations. This was true at one time of copper, which to-day in England is still determined by the so-called Cornish fire-assay, an attempt to imitate in the laboratory the various metallurgical operations in the smelting-works; but nowhere in this country is the assayer forced to employ any particular method for determining copper so long as his certificate indicates the true total percentage of copper in the sample. It is true that both buyers and sellers demand use of the electrolytic method, but only because it is the most accurate. In America the trade accepts the assayer's statement as final, and makes

Jan 1, 1895

By G. T. Lineberry, L. Adler

Reduced clearance a one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity-clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in designing and controlling mine materials handling system.

Jan 1, 1985

By Eliot Blackwelder

For the purposes of this paper, the boundaries of China and Siberia will be taken as they stood about 1907. Except in the Caspian region, it is doubtful if all the oil ever produced in these countries would equal one day's flow of a good Texas well. Considering the vastness of the regions and the variety of strata, it seems strange that these two countries should have made so small a showing in the petroleum industry. No doubt the condition is caused partly by lack of prospecting and of modern methods of development; in larger measure, however, it is evidently because of unfavorable geological conditions over nearly all of east-central and northern Asia. China The known oil occurrences in China are very few. For many years, perhaps a barrel a day has been obtained by primitive methods from wells near the city of Yenchang in the northwestern province of Shensi. A like amount was obtained from wells bored for salt water in the vicinity of Kiating in southwestern Szechwan. The little oil was separated from salt water by allowing it to stand in jars. The salt wells yield also considerable natural gas, which is used to evaporate the salt and also for domestic purposes. There is evidence that wells were bored in this part of China before the third century. It is said that more than 1200 wells have been sunk in that district to depths of 1600 to 2000 ft. (485 to 610 m.) in connection with the salt industry. The scarcity of petroleum in China may be ascribed to three general geologic conditions: First, China contains practically no marine sediments of Mesozoic or Cenozoic age; second, the Paleozoic sediments are not for the most part of the types that generally contribute petroleum; third, the rocks of nearly all ages have been strongly folded, faulted, and more or less intruded by igneous rocks in all parts of China except certain areas in the west and northwest. The mountainous eastern peninsula of Shantung and the similar district of Liaotung in Manchuria to the northeast have the general

Jan 1, 1923

By Eliot Blackwelder

For the purposes of this paper, the boundaries of China and Siberia will be taken as they stood about 1907. Except in the Caspian region, it is doubtful if all the oil ever produced in these countries would equal one day's flow of a good Texas well. Considering the vastness of the regions and the variety of strata, it seems strange that these two countries should have made so small a showing in the petroleum industry. No doubt the condition is caused partly by lack of prospecting and of modern methods of development; in larger measure, however, it is evidently because of unfavorable geological conditions over nearly all of east-central and northern Asia. China The known oil occurrences in China are very few. For many years, perhaps a barrel a day has been obtained by primitive methods from wells near the city of Yenchang in the northwestern province of Shensi. A like amount was obtained from wells bored for salt water in the vicinity of Kiating in southwestern Szechwan. The little oil was separated from salt water by allowing it to stand in jars. The salt wells yield also considerable natural gas, which is used to evaporate the salt and also for domestic purposes. There is evidence that wells were bored in this part of China before the third century. It is said that more than 1200 wells have been sunk in that district to depths of 1600 to 2000 ft. (485 to 610 m.) in connection with the salt industry. The scarcity of petroleum in China may be ascribed to three general geologic conditions: First, China contains practically no marine sediments of Mesozoic or Cenozoic age; second, the Paleozoic sediments are not for the most part of the types that generally contribute petroleum; third, the rocks of nearly all ages have been strongly folded, faulted, and more or less intruded by igneous rocks in all parts of China except certain areas in the west and northwest. The mountainous eastern peninsula of Shantung and the similar district of Liaotung in Manchuria to the northeast have the general

Jan 1, 1923

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

By G. K. Manning, A. R. Elsea, C. R. Simcoe

It was found that a critical boron content exists which yields the maximum boron-hardenability effect in hypoeutectoid steels, as was predicted from the mechanism proposed in a previous paper. The hardenability of boron steels with boron contents between 0.00005 and 0.0017 pct was dependent on the boron content, austenitizing temperature, quenching temperature, and austenite grain size. The effects of these variables on hardenability can be explained by the mechanism previously proposed for the boron effect. A MECHANISM has been proposed to explain the effect of boron on the hardenability of steel.' The proposed mechanism assumes that transformation particles nucleate at concentrations of lattice imperfections where the energy level is high, and

Jan 1, 1957

By David Phillips, George Jura

WHEN Bridgman1 determined the volume-pressure relationships of bismuth to 100 kg Cm-2, he found two small volume discontinuities at 45 and 64 kg em-2. Probably every investigator in high pressures has determined the electrical resistivity of bismuth in this pressure range. Until Zeitlin and Brayman2 reported discontinuities in the resistance of bismuth at these pressures, no one had found resistance discontinuities

Jan 1, 1968

By T. E. Watkins, M. D. Nelson

INTRODUCTION Deeper drilling for oil is becoming more and more the rule rather than the exception. With deeper drilling come additional problems, perhaps the greatest being those brought on by the higher temperatures encountered down the hole. particularly in the Gulf Coast region of Texas and Louisiana. Temperature gradients of the order of 1.8° to 2.0°F/100 ft are not unusual, and a gradient of 2.3"F.'100 ft is found in some areas of Texas. With a mean surface temperature of 74oF, the following temperatures could be expected for a geothermal gradient of 2.0°F; 100 ft: at 10,000 it. 271°F. 12,000 ft, 314°F: 14,000 ft, 354,oF; and 16.000 ft. 394°F. Severe gelation of lime-base drilling fluid in wells that have high bottom hole temperatures has become perhaps the most serious difficulty enconntered in drilling under such conditions. Lime-base drilling fluids have been very succesefully and widely used in the drilling of wells in the Gulf Coast region because of their inherent stability toward contaminants. their ability to suppress the swelling dispersion of bentonitic shales, and their ease of maintainance. The gradual recognition: during the past few years, that these muds were. in themselve. the cause of many difficulties experienced in drilling has led to wide-pread efforts by the drilling industry. to determine the reasons for the failure of these mud systems and to develop mud systems capable of performing satisfactorily under high-temperature conditios. MANIFESTATIONS OF HIGH-TEMPERATURE GELATION it is generally possible to recognize the symptons of high-temperature gelation early enough that advance predictions can be made of serious difficulties. in mud control, and the useful life of the drilling fluids can be extended by proper treatment. Following i.; a list of the manifestations of high-temperature gelation: (1) The drill string 'takes weight' while going in the hole after a trip. In early stages of high-temperature gelation it is possible to notice a slight reduction in drill string weight as the drill pipe is lowred near the bottom of the hole. (2) Excessive pump pressure is required to .tart the circulation of drilling fluid at or near the bottom of the hole when going hack to bottom after a trip. As the severity of the gelation increases it may be necessary to break circulation a number of times when going in the hole. (3) The drilling fluid from the bottom of the hole is thick and often granular or lumpy when pumped up after making a round trip. In a severely gelled drilling fluid system such a condition may be irreversible; that is, it cannot be stirred or chemically treated to produce a satisfactory drilling fluid. (4) Completion tool.. such as logging tools or perforating guns will not sink to the bottom of the hole. On some occasions completion tools will become stuck and require a fishing job to retrieve them if the wire line attached to them is broken. It is often difficult to determine whether the condition of the drilling fluid is responsible for sticking the tool or whether the wire line becomes key seated in a crooked hole and causes the allow difficulty. When there are 110 other symptoms of high-temperature gelation. then the difficulty may usually be attributed to the latter cause. (5) In extreme cases of high-temperature gelation it is necessary to "wash" and "ream" when going back to bottom after coming out of the hole. (6) In many -instance. it has been found to be extremely difficult and expensive to 1111 production packers 2nd tubing in moderately deep oil wells which had been drilled with a lime-base drilling fluid. In such instances-the original mud had apparently "set" to a consistency approaching that of a weak cement. CAUSES OF HIGH-TEMPERATURE GELATION Extensive test; have indicated that a lime-base mud does not develop a highly gelled condition at temperatures below 250°F. whereas above that temperature such condition often develops rapidly. (Fig. 1) concurrently. the following changes are evident ill the mud: (1) The alkalinity of the mud decreases to a very low value. with both caustic soda and lime being consumed. (2) The quartz content of the mud decreases sharply. (3) The bentonitic content of the mud decreases or di-appears, with concurrent decrease or loss of base exchange capacity of mud solids. (4) New compounds formed in the mud have been found to be cal-cium silicate, calcium aluminum silicate, and calcium sodium aluminum silicate. (5) The mud loses the ability to form a filter cake of low permeability. The above characteristics have been discussed, in part. by other authors

Jan 1, 1953

By G. A. Perry, C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). PED is a method by which predesigned pushbacks are sequenced into an optimized period-by- period design. The design that PED Produces is the design used in the field without further modifications. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system. It is in operational use.

Jan 1, 1984

By Walter Miller

Petroleum refining, like other industries in the United States in 1940, focused much attention on its duties and opportunities in the field of national defense. In crdiiter-distinction to the situation during the World War, the industry is well constituted as to existing equipment, processes, and capacity, together with planned additions, to handle any demands that may be made upon it by the defense program needs. Evident throughout was the growing sense of ability to manipulate oil molecules for the production of materials not hitherto considered as being available commercially from petroleum. The development and application of catalytically induced reactions on a broad front is one of the distinguishing characteristics of refining progress during the year. In the hands of the refiner, catalysis has developed into a most important means to secure higher antiknock motor fuels and 100-octane fighting grade aviation gasoline in greatly increased quantity. One illustration of the importance being assigned to catalytic refining is the construction by the Houdry group of an experimental laboratory at a cost of $7'307'30'3, to be staffed with over 100 research men7 solely for the purpose of studying catalytic reactions. In the aviation gasoline picture a modification of specifications by the Government widened the field from which acceptable fuel can be secured, and the continued expansion of the alkylation process in itself promises to go far in filling the demands expected from 50,000 fighting planes. It is conservatively estimated that eyen now the industry can turn out 1,300,000 gal. of 100-octane aviation gasoline daily. The upper limits of octane numbers for regular grades of motor gasoline reached in 1939 were not exceeded, but the average octane number approached the upper level more closely. A survey made of the 1940-model cars showed no rise in average octane requirement of the engines. The trend throughout the year was for greater reliance on the A.S.T.M. method for octane determination. The "1939 Research Method" is less widely used, although still considerably in evidence; the older L-3 method seems to have lost considerable ground and to be on the way out. Re-forming Capacities Increased Interest continued to grow apace in re-forming low-octane naphthas into high-octane gasolines. Some additions, although not great, were announced in thermal re-forming capacity. Interest in catalytic re-forming was greatly stimulated by the technical success of the operation of the converted hydrogenation unit at the Bay-way, N. J., rehery of the Standard Oil Company of New Jersey, mentioned in last year's review, and also by the knowledge that recoverable proportions of toluene are present in the hydroformed (catalytically

Jan 1, 1941

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By Walter Miller

Petroleum refining, like other industries in the United States in 1940, focused much attention on its duties and opportunities in the field of national defense. In crdiiter-distinction to the situation during the World War, the industry is well constituted as to existing equipment, processes, and capacity, together with planned additions, to handle any demands that may be made upon it by the defense program needs. Evident throughout was the growing sense of ability to manipulate oil molecules for the production of materials not hitherto considered as being available commercially from petroleum. The development and application of catalytically induced reactions on a broad front is one of the distinguishing characteristics of refining progress during the year. In the hands of the refiner, catalysis has developed into a most important means to secure higher antiknock motor fuels and 100-octane fighting grade aviation gasoline in greatly increased quantity. One illustration of the importance being assigned to catalytic refining is the construction by the Houdry group of an experimental laboratory at a cost of $7'307'30'3, to be staffed with over 100 research men7 solely for the purpose of studying catalytic reactions. In the aviation gasoline picture a modification of specifications by the Government widened the field from which acceptable fuel can be secured, and the continued expansion of the alkylation process in itself promises to go far in filling the demands expected from 50,000 fighting planes. It is conservatively estimated that eyen now the industry can turn out 1,300,000 gal. of 100-octane aviation gasoline daily. The upper limits of octane numbers for regular grades of motor gasoline reached in 1939 were not exceeded, but the average octane number approached the upper level more closely. A survey made of the 1940-model cars showed no rise in average octane requirement of the engines. The trend throughout the year was for greater reliance on the A.S.T.M. method for octane determination. The "1939 Research Method" is less widely used, although still considerably in evidence; the older L-3 method seems to have lost considerable ground and to be on the way out. Re-forming Capacities Increased Interest continued to grow apace in re-forming low-octane naphthas into high-octane gasolines. Some additions, although not great, were announced in thermal re-forming capacity. Interest in catalytic re-forming was greatly stimulated by the technical success of the operation of the converted hydrogenation unit at the Bay-way, N. J., rehery of the Standard Oil Company of New Jersey, mentioned in last year's review, and also by the knowledge that recoverable proportions of toluene are present in the hydroformed (catalytically

Jan 1, 1941

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By Benny Langston, Frank M. Stephens

Although little information is available concerning small-scale equipment for dust collection in laboratories, it is possible to adapt standard equipment for laboratory use. Dust from laboratory processes may be collected by cyclone separators, filters, electrostatic separators, scrubbers, and settling chambers. IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. considerable data has been accumulated on both operation and design of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process. For most applications standard dust-collection equipment is too large for use in the laboratory; however, for control of dust in large working areas it is often possible to use a standard dust collector, such as an air filter, with branch ducts to eliminate a health hazard. For example, the well-furnished sample-preparation room containing small jaw crushers, rolls, and pulverizers, in addition to the riffles and screens necessary for preparation of samples, presents a perennial source of dust. The authors' experience has shown that a combination system consisting of overhead branch ducts to the individual equipment and floor ducts with grills, where applicable, connected to a central dust collector effectively removes dust generated in preparation of samples. Fig. 1 is a sketch of a downdraft dust-collector for table installation. Similar systems can be built with floor grids. For portable equipment such as laboratory vibrating screens this type of installation with a steel grill to support the heavy load is reasonably efficient. Overhead branch ducts to individual crushing and grinding equipment, although efficient, must be carefully controlled by dampers to prevent excess loss or a change in the composition of the sample. Change in sample composition can result from excess velocity, which causes selective removal of constituents of low specific gravity. Fig. 2' shows the theoretical effect of terminal velocity on spherical particles of different specific gravities in air and water under action of gravity. Fig. 3 shows the effect of air velocity on composition of CaCO, coal mixtures. Although the entrainment of dust particles in a moving air stream is the basic mechanism by which all dust-collection equipment functions, usually intake velocity of the dust-collection system must be controlled to prevent loss of part of the sample. As an example of what may happen when excess velocities are used, a mixture of 50 pct coal and 50 pct limestone was crushed to —10 mesh and fed to a pulverizer equipped with an overhead dust-collection system. Fig. 4 shows the overhead dust-collection equipment used in this test. The pulverizer was set to give a product 95 pct —100 mesh in two stages. Velocity of air passing over the lip of the pulverizer was measured with an anemometer. After grinding, the finished product was analyzed to show the amount of calcium carbonate present. Fig. 3 shows graphically the increase in calcium carbonate as velocity through the dust-collection duct was increased. These data show that at a velocity of 1 ft per sec little if any of the coal was entrained by the overhead draft. At the maximum velocity, about 6.5 ft per sec, approximately 7 pct more coal was entrained than calcium carbonate. From an operating standpoint, this problem can be remedied easily by dampering the line to control velocity. The lowest velocity commensurate with satisfactory dust control should be used to prevent excess loss and, in some cases, selective dust loss. Collection of Dust in Laboratory Processes As in industry, the engineer desires to collect efficiently the dust produced by processes being investigated on a laboratory scale. However, in the collection of laboratory dusts he is faced with two additional problems: 1—The volumes of gas and the quantity of dust that must be recovered are small when compared with the capacity of standard dust-collector equipment, which must be scaled down in design except for collection of dust from large pilot-plant operations. 2—In addition, because of the variety of problems studied in the process laboratory, the engineer cannot design today a dust collector that will meet the conditions imposed by the processes of tomorrow. Sometimes, therefore, he must compromise collection efficiency to minimize the cost of fabrication and the amount of time diverted from the metallurgical to the dust-control problem. For collection of dust from laboratory processes a cyclone separator, filters, electrostatic separators, scrubbers, and settling chambers can usually be adapted for small-scale operations. The following

Jan 1, 1955

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,'-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952