Search Documents

By Walter Crooke

Regenerative hot-blast stoves are now in general use in all parts of the world, and are so well understood and appreciated, that I need not take up your time with an account of their history and introduction into the United States. My object in writing this paper is to give you a short description of a stove that is now being very favorably received and adopted here (see drawing). The stove was first introduced into this country in 1887 by M'Clure & Shuler (now M'Clure & Amsler), who have the management of the patent right in the United States. The English design had to be modified to suit the exigencies of American blast-furnace practice, which, in many respects, widely differs from our English experience. In the first place, the fire-bricks used in America expand to an extent unknown in England, and it became necessary to make special provision for this by increasing the number of cross-walls, and by leaving a space at the top of the stove through which the lining could expand. The expansion laterally was, however, more difficult to provide for, as the combustion-chamber in the center, being the hottest part of the stove, must necessarily expand more than the outer walls, and therefore tend to squeeze up the flue-openings. On first introducing these stoves to American ironmasters, a feel ing seemed to prevail that a " four-pass " stove did not utilize the whole of its surface. They also had an idea that the " two-pass " stove let the burning gas go before all the duty had been extracted from it; so that it was found neceseary to design a stove of a special character to suit their wishes. Hence the "three-pass" chimney top stove now before your notice, the advantage claimed for which is that each stove is independent, requiring no underground chimney flue or stack, and can be erected at a very light cost. The working of these stoves has proved to be very successful wherever they have been introduced.

Jan 1, 1891

By Heinrich Oscar Hofman

IN THE death of Professor Hofman who was born on Aug. 13, 1852 and died on April 28, 1924, the world has lost a great metallurgist and a great author of metallurgical literature. Measured in time his life was not quite seventy-two years, but measured in work accomplished it was much longer than this. It is not surprising that Dr. Hofman became a great scholar for his father, Karl Hofman, was on the faculty of Heidelberg University, and his early days were spent in these surroundings. He studied in the University under such men as Kirchoff and Bunsen and often spoke of the intimate relations he had with them. Following his course at Heidelberg, he studied at the Clausthal Mining Academy where he graduated with honors, receiving the degrees of Mining Engineer and Metallurgical Engineer in 1877.

Jan 1, 1924

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976

By L. V. Wade

Abstract-US Bureau of Mines efforts under longwall research programs to develop the capability to predict support requirements for longwall/shortwall support systems are discussed. Ground control studies are being conducted in conjunction with several longwall/shortwall demonstration projects. Geologic, support performance, and strata behavior are being documented on these projects. A hypothesis is presented for the prediction of support requirements.

Jan 11, 1978

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

Discussion of the paper of Frederick Laist, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1147 to 1162. J. C. DICK, Salt Lake City, Utah :-I would like to ask Mr. Laist why a 10 per cent. salt solution was used. MR. LAIST :-The reason for using salt in the solution is to get .the sulphur. The solution of dilute sulphuric acid has no solvent action on the sulphur even after roasting, and the addition of the salt is made primarily to dissolve the sulphur chlorides. MR. DICK:-I would like to ask also if you made any experiments as to grinding fine your calcines, rather than leaving the coarse material. MR. LAIST :-We have not made any experiments along those lines except in the laboratory, but the objections which we have to grinding are that the difficulties of roasting are very much greater when roasting finely ground material than when roasting coarse material, and the difficulties of leaching are somewhat increased; the percolating system is simpler and easier to manipulate, particularly when acid solutions are used, so that we prefer from our experience not to grind. STUART CROASDALE,* Denver, Colo. (communication to -the Secretary +) :-In order to meet the conditions involved in his ore-treatment problem, Mr. Laist has developed a very interesting and apparently successful metallurgical hybrid which he calls the oxychloridizing roast. The lower floors of the MacDougall furnaces are made to accomplish what used to be done on the " cooling floor" in the old days of salt roasting and " hypo " or brine leaching of silver ores.

Jan 11, 1913

By F. E. Gregory

MINING methods and customs in many districts of England are to this day strangely bound about by the records and traditions of the past. In some mining fields this is more apparent than in others, yet it is everywhere in evidence, for Cornwall with her mines under the sea, Wales with her famous quartzites, and Derbyshire with her remarkable cavern deposits, are all tinctured with quaint customs that have come out of the almost forgotten past. Here, modernism has never replaced tradition, and many of the laws are woven of the woof and warp of ancient custom. Indeed, these things exist because they have come to be part and parcel of the civil laws. And these laws are observed with meticulous care and accorded all the reverence due their venerable age. All activities pertaining to the mining of metals are hedged around by curious and ofttimes clumsy laws, each minute and trivial detail being covered by the civil code, and each petty law enforced by an ofttimes pompous official.

Jan 1, 1933

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982

Jan 1, 1943

Jan 1, 1943

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

Jan 1, 1961

By G. Gutierrez, D. A. Elgillani, M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. In this article, the flotation responses of these minerals in the presence of potassium oleate and sodium silicate are described and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium-bearing minerals such as fluorite from calcite1-3 and scheelite from calcite2,4 and apatite,2,5 for example, almost always involve the use of sodium silicate. The mechanisms by which sodium silicate functions as a depressant are still not understood, probably for a number of reasons. For one thing, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species.&apos; Moreover, the type and concentration of these species depend on the ratio of Na2O to SiO2, the concentration of sodium silicate, and the pH of the system.&apos; At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant. EXPERIMENTAL MATERIALS AND METHODS Pure samples of apatite (Durango), calcite (Iceland-spar), fluorite, and scheelite were used in this investigation. Pure potassium oleate was used as collector, while reagent-grade HC1 and KOH were employed for pH adjustment. The sodium silicates used were samples obtained from the Philadelphia Quartz Co. In one series of experiments, various sodium silicates containing different ratios of SiO2 to Na2O were added to calcite systems. These sodium silicates contained SiO2-to-Na2O ratios of 3.75 to 1, 3.22 to 1, 2.40 to 1, and 1.60 to 1. All other experiments were conducted with the sodium silicate containing the ratio of 3.22 to 1, which is the one that is normally used in industry. Flotation experiments were conducted with 21/2-g charges of 48 x 150-mesh material in conductivity water with an apparatus and technique described previously. Electrokinetic experiments were conducted with both a Zeta Meter and streaming potential apparatus. Particle size was 48 x 65 mesh for the streaming potential experiments. EXPERIMENTAL RESULTS The first series of experiments involved flotation of scheelite in the absence and presence of sodium silicate. As shown in Fig. 1, flotation response was not affected with even the relatively high addition of 1 x 10-3 mole per liter sodium silicate. Interestingly though, no flotation was effected below pH 6 with this collector addition. The responses of apatite to flotation under these same conditions are given in Fig. 2. Similarly, no depression was obtained in basic media under these conditions. Similar experiments were conducted with fluorite, and in this case, depression was noted above about pH 11 with 1 x 10-3 mole per liter sodium silicate (Fig. 3). When calcite was floated with these same levels of addition of sodium silicate, essentially no flotation was possible above pH 7 (Fig. 4). The effect of collector addition with a constant addition of sodium

Jan 1, 1969

After a three-year period characterized by inflation, recession, depressed metal prices, lack of demand, enormous world inventories, and rapidly escalating costs, the Canadian mining industry is showing welcome signs of recovery. A rise in world metal prices and particularly strong demand for gold, uranium, and coal have stimulated the industry in early 1979. In this atmosphere of growing optimism, over 3000 mineral industry executives, economists, geologists, and mining and metallurgical engineers convened in Montreal, April 26-29, for Canada&apos;s largest mining convention, the Annual General Meeting of the Canadian Institute of Mining and Metallurgy.

Jan 6, 1979