Search Documents

By I. R. Kramer

A delay time for yielding in cold-worked face-centered-cubic metals was found. Slip on (123) planes was observed. Glide on these planes occurred during the delay-time period before slip starts on the (111) planes. AN important approach to the study of the anchoring and blocking of dislocations is available through the delayed-yield phenomenon which has been observed in body-centered and hexagonal close-packed metal by several investigators. Clark and his associate1-5 showed that a delay time for yielding is present in mild steels and fine-grain molybdenum. Type 302 stainless, SAE 4130 normalized, SAE 4130 quenched and tempered, and 24s-T aluminum aid not have a delay time. Kramer and Maddin6 studied the delay-yield effect. in metal single crystals. While they found a delay time in body-centered-cubic metals none could be found in the face-centered-cubic metals. Later7 a delay time was found in hexagonal close-packed metals. cottrell8 has proposed an explanation for the difference in the yield phenomena of b.c.c. and f.c.c. metals based upon the anchoring of edge dislocations by the proper types of impurity atoms (C and N). In the body-centered-cubic lattice the interstitial atoms are near a cube edge and can interact with an edge dislocation, while in a face-centered-cubic lattice the distortion around an interstitial atom is of spherical symmetry and cannot anchor a screw dislocation which has practically no hydrostatic component. Cottrell's theory seems to account rather well for the behavior of body-centered-cubic . metals. EXPERIMENTAL PROCEDURE The apparatus used in these experiments is essentially of the same design as described previously.' Single crystals 1 in. long and having a diameter of % in. were placed in a pendulum which consisted of a bar 8 ft long designed with a crystal holder to accommodate the specimen at low temperatures. This portion of the apparatus was supported on fine molybdenum wires. A bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on a set of roller bearings arranged around the periphery of the bar to allow accurate alignment. This bar was propelled by means of a spring-loaded gun and allowed to strike the lead bar in front of the single-crystal specimen. SR-4 type A-8 resistance strain gages were cemented to the specimen and the strain measurements were obtained by amplifying the strain-gage output by means of a high-gain preamplifier. A tektronix 545 oscilloscope was used together with a polaroid camera to record the strain and time sweep. An Ellis Associate Bridge was used to calibrate the strain gages and calibration readings were obtained before each test. The sweep of the time signal was initiated by means of a miniature thyraton which was fired when the two bars came into contact. The single-crystal specimens were cut from single-crystal bars about 12 in. long, grown by a modified Bridgman technique. The aluminum crystals were made with material of 99.99 pct purity while the purity of the copper was 99.999 pct. A cut-off wheel was used to prepare the specimens which were then machined to the desired length. The two opposite faces of the specimen were parallel to each other and perpendicular to the axis of the specimen. The specimens were compressed 1 pct. No machining followed thereafter. In some cases prestraining was carried out in liquid nitrogen by impacting the specimens directly in the apparatus so that subsequent observations could be made without allowing the specimen to warm up to room temperature. The single crystals were compressed 1 pct at room temperature in a hand press without much control of the rate of deformation. In some cases specimens were recompressed to obtain the desired length change. As far as could be determined in these experiments this factor did not seem to influence the results. The SR-4 strain gages were glued with a cellulose type cement onto the specimen surface and baked at 45°C for 12 hr. As a check on the baking treatment gages were allowed to dry at room temperature. All delay time tests in this paper were conducted in a liquid nitrogen bath at -195°C. A schematic delay time oscilloscope trace is shown in Fig. 1. At point B the elastic stress wave caused by the impact reaches the strain gage on the specimen. The portion BC is the elastic strain. In this investigation the strain at point C was used to calculate the critical resolved shear stress by multiplying by the proper modulus depending upon the orientation of the single-crystal specimen. The time between C and D is the delay time portion of the curve. This portion of the curve is fairly flat but does have a definite microstrain associated with it. After the point D is reached the specimen deforms rapidly and the strain reaches a maximum at E. Following this, depending upon the length of the bar behind the specimen, the strain remains constant for a period and then decreases when the reflected elastic wave returns from the end of the pendulum bar. A permanent plastic strain is recorded on the oscilloscope trace and also measured by a strain-measuring bridge. The strain, E p,

Jan 1, 1960

By H. F. Dunlap, R. R. Hawthorne

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By R. R. Hawthorne, H. F. Dunlap

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By J. W. Fredrickson

VERY little information is available in the literature concerning the solubility of magnesium in titanium. Aust and Pidgeon&apos; report the solubility of titanium in magnesium to be 0.0025 pct at 650°C and 0.015 pct at 850°C. X-ray diffraction studies failed to detect any evidence of solid solubility. Based on the fact that the addition of titanium to magnesium increases the c/a ratio of magnesium, Busk&apos; suggested that the Mg-Ti system, like the Mg-Zr, is a peritectic. Eisenreich- eported the solubility of titanium in magnesium to be 0.003 pct at 655°C and 0.064 pct at 760°C. Removal of hydrogen from the melt increased the solubility of titanium to 0.115 pct at 800°C. Eisenreich proposes a peritectic-type diagram for the high magnesium side of the system. Recent work&apos; with Ti-Mg diffusion couples indicate that the solid solubility of titanium in magnesium is extremely small and that there is limited solid solubility of magnesium in titanium. Experimental work on the Ti-Mg system is complicated by the fact that the boiling point of magnesium is considerably below the melting point of titanium. Consequently, the usual alloying methods are impractical. Alloying was accomplished in this investigation by sheath-rolling compressed compacts." The alloys were made from titanium sponge and high purity magnesium. Chemical analysis of the sponge showed 0.04 pct Mg, <0.005 pct Al, <0.001 pct Cu, 0.05 pct Fe, 0.022 pct Mn, <0.0025 pct Ni, 0.007 pct Si, <0.005 pct V, and <0.01 pct Zn. All heat treating was conducted in a protective atmosphere by encapsulating the specimens in fused silica ampules under a partial pressure of helium. Equilibrium was achieved by holding the specimens at temperature for periods of 24 to 120 hr. The alloys were hot rolled, cold rolled, and annealed prior to solution heat treatment. Fig. 1 shows the constitutional diagram obtained for the Ti-Mg system up to 1.5 pct Mg. Oxygen was known to be present in the alloys; therefore, it is necessary to consider the alloys as ternary rather than binary and the diagram should be viewed as a plot of a section through the Ti-Mg-0 system. Other investigatorso have shown that the addition of oxy- gen to titanium stabilizes the a phase. The data presented in Fig. 1 indicate that the addition of magnesium to titanium tends to stabilize the p phase. Armour Research Foundation7 has shown that the addition of magnesium to zirconium lowers the a transus and is classified as a p stabilizer in that system. Magnesium is soluble in solid titanium to the extent of at least 1.5 pct in both the a and /3 phases. No intermetallic compounds or magnesium-rich phases were observed either by light microscopy or X-ray diffraction. However, this does not negate the possibility that such phases exist at higher alloy concentrations.

Jan 1, 1956

By J. M. Hassler

NOWHERE can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, acid as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone.

Jan 1, 1937

By Milo Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland Portland Cement Co. are located at Metaline Falls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in &apos;the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. I is a view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by S ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond wits used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800&apos; C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By D. J. Weintritt, R. G. Hughes

Statistics show arz increase in the average depth of wells drilled in recent years. As a corollary to this trend, drilling fluids have been improved in an effort to meet the problems inherent at temperatures approaching 500°F. Of importance are (1) deterioration of mud components and (2) the effect of solids on filtration and rheological properties. High-temperature, stable water-base and oil-bare muds are discussed. Those areas in which differences exist are pointed out. Results are based on data taken from the Fann consistotneter, rheometer and shear-strength measurements, static and dynamic filtration tests, methy-lene blue test for bentonite solids and specific heat measLrrenlents of muds. INTRODUCTION Higher well temperatures go along with the fact that the average depth of wells continues to increase. Recent data by Gardner&apos; lists 137 completions deeper than 15,000 ft for the first half of 1964 with a record second-half total of 167 wells drilling or proposed. In addition, there has been an increase in drilling for steam for power production or mineral recovery. In this application the depths are modest, but the mud may approach the critical pressure and temperature of water. Scearce and Magnon&apos; report drilling mud used at temperatures of about 700°F in the Salton Sea area of California. Most deep wells have been drilled with water-base muds. In recent years, however, there has been a substantial increase in the use of oil-base muds because of technological advances in effective additives. The significance of this development was dealt with in considerable detail by Simpson and his co-workers.3 Additiona1 field data have now been obtained to indicate that oil muds are competitive in control, performance and cost with the best types of water muds for use at high temperaturc. This parallel offer of two very different fluid systems, each offering a similar variability in performance, cost and convenience, has created the need to evaluate the merits of these fluids under specified conditions so that the advantages and disadvantages of each can be weighed in relation to the over-all drilling program. This paper is not intended as a review of all the factors. Rather, it attempts to emphasize: (1) important condltions and facts peculiar to high-temperature drilling muds, (2) that more than one imposed test condition or testing method is necessary to describe the quality of a mud at high temperature and (3) that elaborate experimental precautions are necessary whenever laboratory data are used in selection of a mud for field use. WHAT IS A HIGH-TEMPERATURE DRILLING FLUID? For the purpose of this discussion, a high-temperature drilling fluid is any system so formulated or treated to economically minimize the effects of temperature on the properties of the fluid. Our experience in drilling fluids suggests that these effects become obvious for many mud materials at temperatures of 300F or higher. It is understood that hydrolysis of starches, depoly-merization of certain organic thinners, or irreversible chemical reactions (such as that of clay and lime) can affect filtration, viscosity and shear strength at less than 300F. However, the temperature level is not a serious point and in no way affects the precautions and techniques used in this study. An up-to-date review of the literature on high-temperature drilling fluids and the many variations was treated by Rogers&apos;in 1963. EXPERIMENTAL REQUIREMENTS TESTING EQUIPMENT AND PROCEDURES With the advent of deeper drilling and increased demand for temperature-stable drilling fluids, new testing equipment and laboratory techniques were devised for the evaluation of drilling fluids subjected to elevated temperature and pressure. While the equipment has not been standardized, it is in widespread use. Milligan et al. Qescribe a filtration cell for determining the filtration properties of drilling fluids at temperatures in excess of 300F. They showed the effect of variations in temperature and pressure on oil and water muds filtered in the 300 to 400F range. The dynamic filtration apparatus described by Simpson6 permits the study of the filtration properties to temperatures of 350F for drilling fluids circulated over sandstone cores. Watkins et al.&apos; describe the use of pressure bombs for studying the effect of prolonged periods of elevated temperature upon the gelation or solidification of drilling fluids. Chisholm et a1.&apos; describe the use of a modified cement consistometer adapted for use in drilling fluid evaluations. A similar consistometer is used in this study, although the application and data-recording method have been changed. The consistency of a mud sample is measured by timing the movement of a soft iron bob which is magnetically moved up and down in the sample container.* Changer in the time of travel and the temperature of the mud at that moment are plotted with a two-point Brown Elec-tronik Recorder. A 10-in. chart with a speed of 4-in./hr is used. Fia.- 1 is a generalized internretation of the data ob-

Jan 1, 1966

By W. M. Brown

SEQUACHEE Valley includes portions of the counties of Marion, Sequachee, Bledsoe and Cumberland. It extends in a general direction parallel with the Great Valley of East Tennessee, some 75 miles northward from the Alabama state line. It is separated from the Valley of East Tennessee by a mountain arm about a dozen miles wide, known as Wallen&apos;s or Walden&apos;s Ridge. The genesis of the valley, geologically speaking, is simple. It is an erosion-valley along the axis of an anticlinal. The point of the wedge remains in a row of low "saw-tooth" hills, running up the center of the valley. These hills are of Lower Silurian age, and consist of Trenton limestone, covered and protected in some measure by chert. Walls of Carboniferous age form the inclosing mountains on either side; whilst a magnificent arch of Hudson River, Niagara, Hamilton and Subcarboniferous strata closes the valley at the

Jan 1, 1886

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry&apos;s law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry&apos;s law is obeyed, one canthen use the Van&apos;t Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors&apos; Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott&apos;s results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville&apos;s new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee&apos;s at Shiprock, N. M. In research, 1954 marked the completion of Kennecott&apos;s Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By Henry M. Rowe

Professor Ruff&apos;s most illuminating paper&apos; describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E&apos;B&apos;, but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the liues B&apos;D&apos;lII represent the experimental results reached by Ruff and Goecke;a AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker&apos;s data; S&apos;E&apos; the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin;5 GS the line A3 after Ooerens and Meyer; 6 and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky&apos;s data. B&apos;D&apos; is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightiiess and its sharp inflection near 6.67 per cent. of carbon, the carbon content of

Jan 1, 1913

By Bauer. Larry G.

The vast coal reserves in the Wyoming, Montana, North and South Dakota region are sufficient to supply the total energy needs of the United States for several hundred years. Not only is there an abundance of this sub-bituminous and lignite coal available, but it is easily obtainable by strip-mining . The overburden varies from several feet to several hundred feet. This western coal has yet another asset, namely, a low sulfur content. Whereas eastern and midwestern coal has a sulfur content of 2.5%, the upper Great Plains coal contains sulfur in the 0.5% range. The importance of the sulfur content of the coal is a direct result of federal government emission standards for sulfur dioxide (SO2). Hand (1) points out that "sub-bituminous coals and lignites have a propensity for retaining this sulfur in the ash under certain conditions which is not evident in higher rank coals." This would tend to reduce further the SO2 concentration in the combustion gases of boilers. Western coal is no panacea, however, in that it is far removed from most population and industrial centers. Furthermore, the moisture content of the coal varies from 20 to 40%. This moisture is almost exclusively inherent, that is, it is chemically and physically bound to the organic matter of the coal. It is believed that the water forms a part of the coal structure perhaps as water of hydration of organic salts or organic acids, perhaps by hydrogen bonding, or perhaps by simple adsorption (2). The primary market for this coal is the electric power industry. Lesser markets will be as coke for the steel industry and possible as a raw material for coal gasification and coal liquefaction plants.

Jan 1, 1983

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman&apos;s curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

By AIME AIME

FEW mining schools possess an art gallery and certainly none can equal the collection of paintings depicting the mineral industries now hanging in the comparatively new building of the School of Mineral Industries at The Pennsylvania State College. Dean Steidle, who conceived the idea, early this spring boasted of 55 paintings in the collection, by 24 different artists, the gallery being appraised at $18,000. Since then, eleven additional paintings have been added. Opportunity will he presented for an inspection at the meeting of the Industrial Minerals Division, to be held at the College, Sept. 24-26.

Jan 1, 1936

By Joseph W. Roe

MaNY questions arising in the work of the mining engineer may be solved quickly and with suffcient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of " innocuous desuctude " may lie in the uifortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer&apos;s attenti011 in terms of&apos; every-day use they may prove of practical hearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in ally way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To Find the Strike. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It mill be assumed for the present that the rein is a plane.

Jan 1, 1911

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of&apos; density. A serial sectioning&apos; technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski&apos; in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

By F. W. Jessen, James N. Howell

The accumulation of paraffin deposits in tubular goods has been recognized as a major production problem since the inception of the petroleum industry. This problem is not limited to any particular geographical area nor is it limited to a specific type of crude oil.&apos; Generally speaking, "paraffin" deposition pertains to the deposition of any predominately organic material in flow lines, and possibly even at the sand face, which would hamper the production of oil. In some fields, a continuous effort is required to remove deposits of paraffin and in order to accomplish this, many unique methods have been devised. The best solution to this problem, however, is to prevent the formation of such deposits. One method which has been tried in a number of fields is the use of plastic pipe. The purpose of this investigation is to compare the relative effectiveness of several plastic materials to aid in the reduction or prevention of paraffin accumulations in surface flow lines. COMPOSITlON OF PARAFFIN DEPOSITS By definition, paraffin deposits are those materials which are insoluble in crude oil at the prevailing producing conditions of temperature and pressure. Such deposits1 s usually consist of small particles of petroleum wax intermixed with resins, asphaltic material, and crude oil. They may also contain a variety of foreign materials such as sand, silt, water, various metal oxides, sulfates and carbonates of iron. barium, and calcium. The petroleum waxes deposited in flow strings usually consist of both a "hard" and a "soft" wax fraction. These waxes are largely aliphatic hydrocarbons with smaller amounts of aromatic and naphthenic compounds. Nathan&apos; has classified the hard and soft wax fractions. The aliphatic hydrocarbons present are those of high molecular weight with high melting points. Reistle3 pointed out that these high molecular weight compounds first separate from the oil due to a sharp decrease in solubility as the melting point increases. The identification of the resins and asphaltic materials rests, at present, on an arbitrary solubility procedure. Under certain conditions, materials which are insoluble in pentane (ASTM D-893) are defined as resins and asphalts. Subgrouping of these materials is made on decreasing solubility in benzene and carbon disul-fide. Shock&apos; found some correlation be-tween the solvent response and the pentane insoluble content of paraftins: higher pentane insoluble fractions are less soluble in any of the commonly used commercial solvents. PARAFFIN CONTROL METHODS The methods used in oil fields to prevent and remove paraffin accumulations can be grouped into four general classes: (1) operative methods, (2) physical methods, (3) chemical methods, and (4) combination of any of these. Operative methods attempt to prevent the formation of paraffin deposits while the other methods are concerned primarily with the removal of these deposits. Plastic coated pipe has been used for a number of years to prevent cor- rosion in wells, and in manv instances paraffin deposits have -been greatly reduced. Field observations have indicated that plastic coated pipe not only reduced paraffin accumulation but in some cases eliminated deposition completely; however, data are needed to demonstrate the relative effectiveness of plastic materials. Deposition Apparatus The pipe used to determine the effect of velocity on rates of deposition was %- and 2-in. nominal diameter, and 5 ft in length. Steel, butyrate, rigid PVC, kralastic resin-type plastic pipes, epoxy coated pipe, PVC lined glass fiber pipe, and aluminum pipe were tested. Steel pipe was used as a control. Fig. 1 is a schematic diagram of the apparatus showing the relative position of the separate units making up the equipment. In order to facilitate the installation and removal of the test pipes in the apparatus, O-ring seals capable of sustaining pressures of 50 psi were provided at each end. Test pipes were submerged in a cold water bath maintained at or below room temperature by circulating water through copper cooling coils packed in ice. A hot water bath equipped with immersion-type heaters, stirrers, and a thermoregulator was used to maintain the temperature of the oil prior to introduction into the piping manifold. The capacity of the oil reservoir was 30 gal. A 33-gal/min centrifugal pump, capable of producing turbulent flow velocities in the test pipes, was used to circulate the oil through the system when using %-in. pipe; and a 70-galjmin centrifugal pump was used in later tests using 2-in. pipe. A by-pass arrangement made it pos-

By W. M. Peirce, R. K. Waring

Zinc of high purity offers definite advantages in certain fields. A process by which zinc of 99.99 + per cent purity is produced by pyro-metallurgical methods is described in this paper. The process consists of a fractional distillation following the primary reduction; this fractional distillation employs the principles of rectification for the separation of lead and other high-boiling impurities and cadmium and other low-boiling impurities. Theoretical Considerations Involved in Production of High-purity Zinc by Distillation Fractional distillation, fractional condensation, and rectification are recognized methods of separating mixtures of liquids. In the field of organic liquids these methods are widely used but not commonly to effect as complete a separation of liquids as is done in the problem under consideration. Zinc boils at 905" C., cadmium at 778" C. and lead at about 1620" C. Zinc may contain from several hundredths of one per cent to over one per cent each of cadmium and lead, and the problem is to reduce these impurities to a few thousandths of one per cent. For lead and zinc, the spread in boiling points is substantial, 715° C., while for zinc and cadmium it is only 127" C. The basic limitation of any separation by distillation may be found from the relation between the equilibrium composition of the vapor and the liquid for all mixtures of the two substances involved. If a mixture of constant boiling point is found, or if a stable compound that vaporizes without dissociation occurs, there is a definite theoretical limit to the degree of separation that is possible when operating at atmospheric pressure with respect to that mixture. Otherwise, any degree of separation is theoretically possible. The equilibrium composition of vapor in contact with liquid mixtures of zinc and cadmiurn at the boiling point has been determined experi-

Jan 1, 1937