Search Documents

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

By George Branner

THERE is no record of the commercial production of bentonite as such in Arkansas up to the present although fuller's earth has been. mined intermittently in the state1 from 1891 to 1922. Very nearly all of this was obtained from decomposed basaltic dikes.2 Recently three bentonite deposits of close stratigraphical relationship have been identified in the Coastal Plain region of southern Arkansas, which suggests that there may be a considerable quantity of commercial material available. LOCATION AND ACCESSIBILITY The three deposits are located respectively in the SE. ;1/4 SE. ;1/4 sec. 13, T.- 2 S., R. 13 W., Saline County, the SE. ;1/4 SE. 1/4 sec. 18, T. 5 S., R. 16 W., Hot Spring County, and in sec. 22, T. 12 S., R. 19 W., Ouachita County. The Saline County deposit is 14 miles by state highway 167 south of the city limits of Little Rock and 1 mile west by dirt road. This deposit is 12 miles south of Ward switch on the C. R. I. P. Railroad and 11 miles east of Vimy Ridge by dirt road. Vimy Ridge is also on the C. R. I. P. Railroad. The Hot Spring County deposit located in the SE. ¼ SE. ;1/4 sec. 18, T. 5 S., R. 16 W. is about 100 yd. north of Durian switch on the C. R. I. P. Railroad and on state highway No. 9, 5 miles southeast of Malvern. The Ouachita County deposit has not been accurately located but lies in sec. 22, T. 12 S., R. 19 W. It is approximately 2 miles by road from Chidester on the Missouri Pacific Railroad.

Jan 1, 1929

By Irving Hartmann, H. P. Greenwald

READERS of this journal are familiar with the danger of coal-dust explosions in mines and with recommended means for preventing them. The subject was treated in a paper by R. R. Sayers in the January 1943 issue, as well as in several previous articles. Similarly the danger of dust explosions is generally recognized in the handling of grain dust, flour, starch, sugar, and other carbonaceous products. However, until recently, few people realized that an analogous, real explosion hazard exists wherever dust suspensions of certain finely divided metal powders are formed. This lack of knowledge was in part due to the fact that until a few years ago only a small number of metal powders, such as aluminum, magnesium, zinc, iron, and tungsten, were produced, in comparatively small volume, and partly because information on the explosibility of metal powders was lacking.

Jan 1, 1945

By Robert Palmer

So MUCH has already been written on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have, come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place.

Jan 1, 1930

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By C. R. Breck

THERE has been a running discussion over the past several years with respect to the life and adequacy of our natural gas reserves. Some of the experts agree on one phase of the subject at least-that eventually it will be necessary to augment deliveries of natural gas in the northern markets by the development of a more or less comparable synthetic gas made from coal. The purpose of this paper is to point out: 1. It may be later than a good many people think-the demand for addi¬tional domestic and commercial pipeline gas in at least one section of the North will probably be felt rather keenly before an adequate synthetic pipe¬line-gas project, developed on economic lines, could be completed, even if initiated in the near future. 2. The evidence is considerable that such a project would be technically sound and economically self-supporting, although the margin of profit at first might be so small and the magnitude of an economic enterprise so great -that financing would be impossible without Government aid in some form or other. The part of the country referred to is the heavily populated section in the northeast of the United States. To simplify an examination of the situa¬tion, let us take the potential marketing areas within range to the north and east of the three pipelines: 1. Tennessee Gas Transmission Co. as it enters Erie County, New York state. 2. Texas Eastern Transmission Corporation just before the tap that sup¬plies the general Philadelphia area. 3. Transcontinental Gas Pipe Line Corporation as it enters the state of New Jersey. The sources of gas for these three pipelines are in Texas and Louisiana. The ultimate maximum combined capacity of the three lines at the points stated is approximately 1,200,000,000 cu ft per 24 hr at the maximum load factor probable of attainment in normal operation. The areas supplied by the three lines north and east of the points stated, or assumed as eventual markets, are: 1. Central New York state, from Buffalo to Albany (both inclusive).

Jan 1, 1953

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By AIME AIME

UNDER the auspices of the Institute's Committee on Industrial Preparedness, a symposium was arranged for the Annual Meeting on the subject "Ores, Metals, and the War," with many well-known Government men and industrialists participating. Wilfred Sykes, president of the Inland Steel Co., of Chicago, presided, with C. K. Leith and Clyde Williams as vice-chairmen, Mr. Williams presiding over the latter part of the meeting. On the Auditorium stage in the Engineering Societies Building was a formidable corps of "experts," with an audience of several hundred to hear what they had to say and to ask questions.

Jan 1, 1942

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

By AIME AIME

AN enthusiastic crowd, cheerfully confident that the upturn in the oil industry has arrived, gathered in Los Angeles on Sept. 29 for a Petroleum Division meeting arranged by the Southern California Section. The assembly room of the California Oil and Gas Association was the place of meeting. H. Norton Johnson was in the chair for the morning session, with about eighty members and guests present. Four papers were presented before lunch and a fifth, on electrical coring, was withdrawn as the work on which it was based is still confidential. Joseph Jensen read his contribution on the "Kettleman Hills Middle Dome Unit Plan" and, as he had an active part in framing the plan, his outline and discussion of it was authoritative and informing. J. H. Woods asked concerning the operation of the casing-head gasolene plant under the plan and was informed that one company would operate the plant and royalties would be paid participating companies

Jan 1, 1933

By A. M. Gsudin, F. W. Bloecher, C. S. Chan-s, P. L. De Bruyn

M ANY elements can now be obtained in radioactive form. The radioisotopes have the same chemical properties as the corresponding inactive forms, differing from them only by their nuclear instability. This combination of properties permits radioelements to act as atomic tracers, the tracer atoms revealing themselves at the time of their decay with emission of electrons and positrons (beta radiation), helium nuclei (alpha radiation), or electromagnetic radiation (gamma radiation). The tracer technique is particularly attractive for the study of surface chemistry problems in general and flotation problems in particular because of its extreme sensitivity. A large proportion of the ionizing events, initiated by the characteristic decay emissions in a radioactive sample, can be recorded by radiation probes of suitable design and geometry. An idea of this sensitivity can be gathered from the following example: assume that 0.001 mg of pure RaD (radiolead), a beta-ray emitter, is used in a flota¬tion tracer experiment. This is 1210 X 10-1 mole; since the fraction trans¬formed per second (the so-called decay constant), is 9.92 X 10-10, the number of ionizing events per second would be (6.023 X 1023 X y,,, X 10-1) X 9.92 X 10-10 = 2.845 X 106. (The decay constant is expressed in sec-'. Its product with the half life, expressed in seconds, is the pure number, natural logarithm of 2 = 0.693. The half life is the length of time required for decay of one half of the total number of radioactive atoms of one particular type.) (See reference (1) at the end of this article.)

Jan 1, 1948

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Technical graduate, aged-31, with experience as surveyor, chemist with a sulphur company, practical miner, and as chief engineer of an iron mining company, desires a position as mining engineer or superintendent. Speaks French and German. No. 165. Member, aged 31, married, graduate Yale and Massachusetts Institute of Technology, six years' experience in coal and iron mining, from engineer to general superintendent, desires position with large coal or iron company. Will go anywhere. References. . No. 167. Member, technical graduate, with experience as machinist, chemist, construction engineer, and manager-of mines in the United States and Mexico, desires position .as mine superintendent or manager. Speaks Spanish. No. 168. Member, technical graduate, aged 26, with experience as engineer, mine foreman, assistant superintendent for a pyrite mining company. Experience includes diamond drilling, shaft sinking, underground work, milling of pyrites, and mine accounting. No. 169.

Jan 12, 1914

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958

By AIME AIME

BY the end of 1943, the United States will be able to produce aluminum at a rate of 1,150,000 tons a year. How much aluminum is 1,150,000 tons? It is sufficient to replace every railroad passenger car in this country three times a year. Or, it would put a thirty-piece aluminum cooking utensil set in every one of America's 34,000,000 homes with enough metal left over to make 5,000,000 miles of aluminum transmission cable, such as was used in the electrification of much of rural America. Expansion of aluminum production capacity for the war program has occurred in three steps: (1) expansion by private industry; (2) the letting of contracts by the Defense Plant Corp. for the construction of additional aluminum plants which may remain after the war to compete with existing facilities; and (3) the more recently announced D.P.C. program for the building of emergency plants to make aluminum, using stand-by power available in large metropolitan centers power of relatively higher cost, making it questionable whether such plants, now gravely needed, will be able to compete in a peacetime economy.

Jan 1, 1943

By OTTO HERRES

UTAH has enormous deposits of high-grade bituminous coal. The United States Geological Survey estimates that there are 13,130 sq. mi. of land in Utah known to contain workable coal and these extensive fields contain 196,000,000,000 tons of coal. Growth in population and development of industry in the intermountain and Pacific coast regions will in time give Utah a place with the great coal producing states of the country. Even today, faced by adverse conditions in competition with cheap fuel oil from southern California, water-power throughout the western states in general, and comparatively high freight rates to its distant markets, the Utah coal industry is notable in many respects. In recent years, Utah has led the United States both in the percentage of its mines in class 1, mines producing more than 200,000 tons a year, and in average production per man per day, which was 6.01 tons in 1921. In Mineral Resources of the United States, 1921, Part

Jan 1, 1925

By W. E. Wrather

SERIOUS consideration was given by the Petroleum Division to a wide variety of subjects, during six busy sessions at the Annual Meeting. Beginning with a joint session on engineering research and production engineering, Tuesday afternoon, conducted by E. A. Stephenson and H. C. Fowler, problems of petroleum technology, domestic and foreign production, proved oil re- serves, economics, and stabilization were mooied almost without interruption until nearly everyone was "talked out,' and the meeting was adjourned at the end of the annual Petroleum Division dinner, late Thursday night.

Jan 1, 1933