Search Documents

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

SME-AIME Fall Meeting and Exhibit

Jan 9, 1979

By Scott Turner

PRESIDENT SCOTT TURNER officiated as chairman of the opening session on mining methods, Monday morning, Feb. 15. The first paper was that of Max H. Barber on open-pit mining in the Lake Superior district, read by C. F. Jackson. W. L. Taylor stated that liquid-oxygen explosive had been tried but that the operators are satisfied with the explosives used; lb. of dynamite breaks one ton of rock. Although black powder is considered the most effective explosive, the factor of safety has decided in favor of high explosives. Lucien Eaton told of the Michigan Lime and Chemical Co.'s large L. 0. X. plant at Rogers City, Mich. Mr. Turner referred to this plant, also said that the Bureau of Mines is shortly to issue Bulletin 349 completely covering the use of L. 0. X. from its inception. W. D. B. Motter, Jr., gave some items concerning Chuquicamata, Chile. Twelve years ago the blasts moved 850,000 to 1,000,000 tons, but average shots now move 250,000 to 300,000 tons. One pound of L. 0. X. breaks 3.7 tons, against 3.1 tons by dynamite. Another speaker told of some large dynamite blasts in open pits, one of 360,000 Ib. in March, 1931, and another of 430,000 lb. to be shot in 1932. Tests have been made to determine the effect of large shots on the surrounding country. Mr. Taylor said that 4- and 5-yd. shovels were preferable to those of 8 yd.; their performance is better and cost is lower.

Jan 1, 1932

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By JOHN A. FULTON

THE Comstock Lode is in Storey County, Nevada, and extends in a north and south direction through the towns of Virginia City and Gold Hill, with a total length of 4.27 miles. Its mines have produced silver and gold to a known value exceeding $400,- 000,000 since 1859, when the work first began. More than $126.000,000 was paid in dividends by the mining companies, although much more than this was probably realized from the ore, because many milling companies were independent companies owned by the directors and superintendents of the mines. The milling companies' contracts called for an extraction of only 65 per cent and, as much of the ore was worth $100 a ton and up- ward, they must have recovered substantial amounts for their own accounts over and above this guarantee. Gold was discovered in the spring of 1850 by a party of Normons bound for California. The discovery was made at the mouth of Gold canyon near Dayton, on the Carson River, about 10 miles south of Virginia City.

Jan 1, 1929

Jan 1, 1879

By Zay Jeffries

IT HAS been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat and cooling either rapidly or slowly with nearly pure iron and slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point, which is near 700° C. The present paper will not consider these old and well-known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, in 1886, reports that both working steel and heat treatment of steel in the blue-heat range are highly injurious. Recently, however, some metallurgists believe that the straightening of warped steel forgings at a blue heat produces a beneficial effect on the metal.2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes -in Iron and Steel Below the Thermal Critical Range, which has the following personnel: R. R. Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F.C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood: This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 2, 1920

By AIME AIME

THE growth of the spirit of progress and mutual aid which motivated the founders of the Institute sixty years ago in Wilkes-Barre was vigorously demonstrated at the sixtieth anniversary meeting held there on May 22. Committees headed by Cadwallader Evans, "resident director" of the Institute, and Paul Sterling, chairman of the local section, had arranged for a full-day tour of the northern anthracite field, so that the hundred and fifty members and guests who had come for the celebration of the anniversary might see the changes and progress made in that field in recent years. More than forty automobiles were in line in the cavalcade which left the Westmoreland Club at nine- thirty. Operations visited were fully described in the May issue of MINING AND METALLURGY, so it is enough to say that after a seventy-five mile drive through the beautiful Susquehanna Valley and over the rolling green hills of northern Pennsylvania a stop was made for lunch at Forest City. Carey, Baxter and Kennedy, contractors at the stripping operations there, had provided, in the shelter of tents, a well-prepared luncheon and other refreshments. The return trip was made by way of Scranton, arriving at Wilkes-Barre at five- thirty.

Jan 1, 1931

Jan 1, 1967

By AIME AIME

ARRANGEMENTS for the Annual Meeting of the Institute were well advanced at the end of December as the following program will show. Heretofore this has been printed separately, but its inclusion in the Annual Review issue of MINING AND METALLURGY will, it is hoped, make it more easily available for reference until the final program is issued, which will be distributed at the meeting. Added details will appear in the February issue. Last year's meeting drew a record crowd of over 2300 which should be exceeded this year. Early reservations at the headquarters hotel, the Waldorf-Astoria, or any other convenient hotel are desirable, as are prompt reservations for the Annual Dinner. No one need worry about too much speechmaking this year, for the honors will be awarded and accepted in a few words instead of a few paragraphs, in seconds rather than minutes.

Jan 1, 1939

THE 125th meeting of the Institute was held in New York, Feb. 20-23, 1922, inclusive, and was the most successful annual meeting of the Institute ever held; there was a larger registration, there were more sessions of importance, and a greater number of sessions, than in any previous year. The total registration was 1331, comprising 351 New York members, 393 visiting members and 587 guests. At the annual business meeting of the Institute, held on Tuesday, Feb. 21, with President Ludlow presiding, there was a much larger attendance than usual. The report of the tellers was read and the following officers were declared elected: Arthur S. Dwight, Director and President-District 0 J. V. W. Reynders, Director and Vice-president-District 0 A. R. Ledoux, Director and Vice-president-District 0 Charles F. Rand. Director-District 0 George D. Barron, Director-District 0 William H. Bassett, Director-District 1 Thomas B. Stearns, Director-District 8 William Kelly, Director-District 5

Jan 3, 1922

By Wilhelm Borchers

IN all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity . towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly growing number of inventions, inasmuch as the chief con¬stituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity fir those elements which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to beat the refining-slag to the highest point of its chemical activity ; to prevent the iron from entering the slaw, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1910

By AIME AIME

THE Annual Meeting-numerically the 162d meeting-of the American Institute of Mining and Metallurgical Engineers will be held at the Pennsylvania Hotel, 7th Ave. and 33d St., New York, Feb. 18-22, with the exception of the following events: the Mineral Industry Education Division will meet Sunday afternoon and evening at the Columbia University Men's Faculty Club, 400 West 117th St.; and a meeting of the Section Delegates, the annual business meeting of the Institute, and an executive session of the Board of Directors will be held in that order Tuesday afternoon in the Engineering Societies Building, 29 West 39th St., where the Directors will meet in the evening following their annual dinner to the Section Delegates. The Pennsylvania--one of the Statler group of hotels-was selected as headquarters because it has the physical equipment and facilities-for registration, technical sessions of all sizes, luncheons, social events, etc.-as well as the prominence and location desirable for an Institute annual meeting. (A tip for Tuesday afternoon and evening: You can walk underground from the Pennsylvania to within half a block of the Engineering Societies Building,)

Jan 1, 1945

By Georgc E. Collins

SEVERAL years ago, I estimated the total stock of gold in the world to be about a thousand million ounces, of which rather over one-third was available for monetary uses. Robert H. Ridgway has estimated the world's production from 1493 to 1927 as slightly over this amount. Of this total, 1.5 per cent was produced between 1493 and 1850 (before the Californian and Australian goldfields began to flood the world with gold), 331/2 per cent from 1851 to 1900, and 511/2 per cent from 1900 to 1927. Allowing for loss by attrition and permanent consumption in the arts, and for loss of buried treas¬ure, my first-mentioned estimate is perhaps not far from the truth; but my estimate of the monetary stock was certainly too low. Of the total production stated by Rid-way. 28 per cent came from North America. 26.9 per cent from Africa, 1.6.8 per cent from Australasia, 12.4 per cent from South America, and 11.2 per cent from Asia. Excepting that from the African conglomerate beds, the ultimate origin of which is still the subject of controversy, by far the greater part of the total production was derived from alluvials. Weighing all contingencies, it is improbable that any such production as has been made during the last forty years will be repeated in any similar period, if the present price level is maintained. The gold standard today seems firmly established except for temporary digressions. Nevertheless, no well-informed mining engineer will venture to assert the probability that the material for its maintenance throughout future generations can be furnished.

Jan 1, 1932

By L. E. Young

IT has been said the British Empire was built on British Coal. In all the postwar planning for Great Britain the necessity for producing cheap coal and the prosperity of the coal industry are given first consideration. On Jan. 23, 1945, there was released in London a "Report to the Colliery Owners" which had been awaited with great interest. This was entitled "A Plan for Coal" and was the recommendation of Robert Foot, chairman of The Mining Association (Colliery Owners), prepared at their request. Presentation of the "Plan" at this time is particularly significant as it is an answer to the demand for nationalization of the coal industry by the Labour Party and at the same time is a carefully considered program for postwar reconstruction, prosperity, and stability. In the words of Mr. Foot, If the coal industry for the first ten years after this war is to find itself in a situation similar to the one it occupied for the ten years following the last war, with its record of disputes, strikes, stoppages, short-time working, unemployment, and, with it all, a completely insufficient margin of profit, and all the insecurity and instability in our basic industry that was brought with them, it is goodbye to any real prospect of full employment, social security, and high standard of living. To present an elaborate review of the conditions which have brought to a crisis the unfortunate situation in the British coal industry is here unnecessary, but certain of the salient points

Jan 1, 1945

By AIME AIME

THE official opening at the 134th general meeting of the Institute was held on Oct. 6, but it was prefaced by two round table conferences on Oct. 5. The open-hearth group held the fourth of their semi-annual conferences at the William Penn Hotel, devoting the morning session to discussing a paper by R. L. Cain on the "Manufacture of Forging Steel by the Open-hearth Process," and the afternoon to discussing P. H. Shaeffer's paper on the open-hearth charge. At the Bureau of Mines, a round table conference on the combustibility of coke was held on Tuesday morning, and the afternoon was devoted to a similar conference on the testing of coke. The formal opening session of the meeting assembled in the Music Hall of Carnegie Institute at 10.30 a. m. Graham Bright, chairman of the Pittsburgh Section; called the meeting to order and presided. President Taylor welcomed the visiting members and guests to his home city and reviewed briefly the advancement of mining in the past half century during which, for ex- ample, the coal output had increased from 53,280,000 tons to 523,357,000 tons per year. He emphasized the important part Pennsylvania played in mining and brought out the principal changes that had taken place in methods. In part, his remarks were as follows: The centennial year, 1876, found the coal business of. this country, as a whole, producing 53,280,000 tons, of which amount the bituminous mines of this State yielded 24 per cent. In 1925, this country produced 523,357,000 tons of coal, of which Pennsylvania produced 24 per cent.

Jan 1, 1926

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum's residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years' absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By AIME AIME

AS a new departure the annual business meeting was held at 4 p. m. on Tuesday, Feb. 16, instead of in the morning, as previously. The retiring President, Robert E. Tally, called the meeting to order and briefly spoke of the large measure of success that had been attained in balancing the budget of the Institute in 1931, so that, although receipts had declined over $26,000 compared to the previous year, expenditures had come within $3,000 of income. He referred in complimentary ,terms to the work of the committees on Membership, Admissions, Papers and Publications, and MINING AND METALLURGY, from which more would be heard late:. He also announced that a large and important committee on economics has been under consideration, and will be announced later. As an evidence of growth it was noted that a new Division, Mineral Industry Education, had been organized just an hour previously.

Jan 1, 1932