Search Documents

By R. M. Brick

Segregation can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-I2 per cent Si alloys. The phasial condition implicitly described above—solidification over a range of temperatures with a compositional difference between solid and liquid—is found in nearly all solid solutions or combinations of solid solutions and eutec-tics, Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually deter-minable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be described first because it is an essential part of the picture. Coring Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus I, 3, 7 and solidus 2, 5, 8, and where the vertical I, 4: 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. Ib) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1945

By AIME AIME

IT IS impossible in this short sketch to give a detailed description of each part of the plant at Bethlehem, therefore, only such facts will be touched on as are necessary to give a general idea of the works. The extent of the plant, and the fact that the units making up the various departments are located in different parts of the works, make it impracticable to mention the departments in any regular order with regard to their location. They are, therefore, mentioned approximately in the order of their relation to each other with reference to their functions in the making of the various products.

Jan 1, 1924

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896

By E. A. Anderson

In 1918 the American Society for Testing Materials held a symposium2 on what was then known as season cracking. The sessions included six papers, all on brass. During the ensuing 26 yr., many new workers have come into the field and several other metals have been found subject to failure by stress-corrosion cracking when the right combination of stress and environment is achieved. It is not surprising, therefore, that the present symposium has brought forth 29 papers covering alloys of seven important metals. The phenomenon of stress-corrosion cracking is not necessarily confined to these seven metals. Dix3 has stated, "Indeed, it is probable that ingenious investigators can find solutions which will stress-corrosion crack any known metal or alloy." Mears, Brown, and Dix4 have indicated that stress- corrosion cracking failures are not necessarily limited to metals but may include the plastics. It is to be expected that the increase in the number of metals known to crack in service and the general emphasis on such failures at a symposium such as this will alarm many to whom the subject is un- familiar. Such alarm is not justified by the record. It is true that stress-corrosion

Jan 1, 1945

GENTLEMEN : Herewith are submitted reports for the calendar year 1933 of your Treasurer and the Chairmen of the following standing committees: Finance, Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for additional details of the year's activity. Finances.-Income for 1933 from all sources totaled $121,690 com- pared with $138,331 in 1932. Incidentally, this exceeded the income as estimated in the budget by $7,190; the largest item being a "surplus" of $3,316 over the budget expectancy as to member dues. As compared with 1932 the most important items of shrinkage in income were $9,000 from dues and initiation fees; $5,500 from the magazine, MINING AND METALLURGY; and $2,500 from sales of publications other than the magazine.

Jan 1, 1934

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. 'rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950

By John H. Harden

In the valuable paper of Mr. Dunbar D. Scott and its varied discussion, on the evolution of mine-surveying instruments, the tripod-head has not received the attention it merits. During the last 50 years this very necessary adjunct to the surveyor's instrument has been much improved. The legs are of better construction; and the devices for laterally moving the instrument over the station-point and for quick leveling, without the use of the screws, have given to the instrument fitted with the modern tripod-head the same facilities possessed by the oldfashioned ball-and-socket, with more perfect accuracy, not attainable in the latter, while saving from 30 to 50 per cent. of the time required for setting the instrument over a station. For the purpose of extending the discussion to this import-

Jan 1, 1902

By R. J. Evans, A. G. Revesz

Silicon films have been grown by chemical reaction on (111) silicon substrates. The surfaces were examined by various microscopic and interfero-metric methods. Surface structures are classified into two groups depending on whether the angles between the bounding planes and the (111) surface are small (<3 deg) or large (> I0 deg). A layer-gvowth mechanism is postulated to explain the topography and the influence of growth parameters. Growth proceeds by lateral expansion of the (111) layers in (211) directions, thereby forming steps. The step edges are perpendicular to the direction of expansion and are thus along (110) directions. Step bunching md surface nucleation both play an important role in modifying the flow pattern and in the step regeneration. These are influenced ver?) much by impurities, especially oxygen. Although the growth is a result of a surface-controlled ga: reaction, it is very similar to growth from an impure solution. OVERGROWTH ("epitaxial growth") of silicon is important and widely used. During the past years several investigators have observed various topographical features or so-called faults on the grown films. A study of the surface morphology gives some insight into the growth mechanism. I) EXPERIMENTAL Silicon films have been grown on silicon substrates by a method described by Theuerer.&apos; Silicon is formed by reduction of SiCl, in hydrogen. The rate of incidence of SiC1, was varied between 5 x 10"6 and 2 x 10&apos;4 moles min-&apos; cm-&apos;. The mole fraction of Sic4 in the Hz-SiCL mixture was about 5 x X Both the rate of incidence and the mole fraction were calculated on the assumption that the Hz bubbling through the SiC1, reached equilibrium saturation. Assuming uniform velocity distribution, the linear velocity of the gas in the reactor tube was estimated to be 2 cm sec-l. The temperature of deposition was varied between 1070" and 1260°C. Chemically polished p-type silicon wafers of 20 to 100 ohm cm resistivity were used as substrates. These were within 1/2 deg of a (111) orientation. The thickness of the grown n-type film was determined by two methods: a) measurement of the depth of the p-n junction taking into account the junction shift due to diffusion, b) measurement of the traces of stacking-fault tetrahedra on the (111) plane.&apos; The agreement between the two methods was better than 20 pct. The rate of growth varied between 0.2 and 4.0 pmin-&apos;. The formed films were examined by reflection and light-section microscopy, and by multiple-beam interferometry. Phase-contrast illumination revealed height differences of about 30A. For measuring heights greater than 1 p a light-section microscope3 was used. The resolution by multipke-beam interferometry4 was between 50 and 100A. Crystallographic directions on the surface were determined by X-ray and from the orientation of etch pits and stacking faults as revealed by Dash etch (I part HI?, 3 parts HNOJ, and 12 parts CH3COOH). Some specimens have been investigated by electron microscopy. Platinum-shadowing and carbon-replica techniques were used to show the fine topography and reflection diffraction to determine the structure of the grown layers. 11) RESULTS The topographical features can be classified into three groups. he first group is comprised of fine ridges (striations). The second group consists of structures, which are bounded by planes making angles of less than 3 deg with the (111) surface. They are, therefore, vicinal planes. Structures which closely resemble growth or etch pyramids from the third group would normally be bounded by perfect low-index crystallographic planes. In this case they are deformed. The angles between the bounding planes and the (111) surface are generally larger than 10 deg. The fine ridges are present, even on the smoothest surfaces, as shown in Fig. 1. They are along a (110) direction. The height differences could not be resolved with interferometric techniques. The basic characteristic structures of the second group are depressions and hillocks. These are bounded by three planes, two of them with larger slopes than the third one. The edges between the planes, as projected to the (111) surface, point in (211) directions. Various habits of these structures are shown

Jan 1, 1964

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Dispersion-containing titanium-copper alloys were prepared having mean free paths varying from 1.0 to 9.7 P. Tensile studies at room temperature and at 1000°F showed that little or no strengthening occurred when the mean free path exceeded 3 p. However, at lower values of mean free path appreczable strengthening was observed. A considerable amount of strengthening also resulted from copper in solid solution. DURING the past several years, an increasing amount of study has been devoted to dispersion hardening, an alloying process in which increased strength is obtained through the addition of a ran-

Jan 1, 1961

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By C. L. Clark

EVERY user of steel should ask himself whether or not he is taking full advantage of the discoveries of the steel metallurgists during the last few years, or is merely buying grades that looked to be the best five or ten years ago for various specific purposes and have since proved perfectly satisfactory in his plant. If he has not kept abreast of the times, then it is probable that something better has been developed, or something just as good that costs less. Though this article will have to do with steel for high-temperature applications primarily, marked advances have been made in steels for other purposes as well.

Jan 1, 1940

By John B. Cook

Most of today&apos;s open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO&apos;s 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

By James A. Clem

Approximately 2000 years ago, the Lord admonished the scribes (lawyers) and pharisees (religious leaders of that time) that they had paid the tithe but had omitted the weightier matters of law, judgment, mercy, and faith. (Matt. 23:23) I want to talk about "The Weightier Matters of Law." In a situation where big government is trying to have an effect on even small details of a work activity, otherwise simple situations become complex. Regulations are written to such detail that constant compliance with strict interpretations can be a nightmare-not to mention off the target of the intended purpose for the regulation. One soon recognizes the onerous characteristics of federal statutes. Another admonition the Lord gave those lawyers and pharisees back then was that they tended to strain at a gnat and swallow a camel! He meant that the pharisees were given to devoting themselves to the strict interpretation of law by writing hundreds of subrules or interpretation to law. In doing so they eventually lost sight of the original purpose of the law. I think they were being told, keep the law-but don&apos;t neglect to humanize it Keep it simple Recognize the purpose of why the law. "Mix in" a common sense approach. Someone once said, "Common sense is instinct -enough of it is genius." Today, as 2000 years ago, we need more "genius" displayed by legislators in considering the weightier matters of law. First of all true legislature genius calls for a declarative statement about the purpose of the statute and a fair, objective analysis of the ground rules by which it will be implemented. In the Health & Safety Act of 1969, the "findings and purpose" as set forth in Section 2 do define its purpose. I believe most of us affected can be in accord with the reasons advanced for the legislation. However, beyond those well-intentioned few paragraphs, we very quickly run into trouble. Congress complicated the simplicity of the statement of purpose by mandating government intervention into areas that cannot be effectively legislated, nor even should be legislated. The Act provided for broad gaged regulation which is unnecessary, inappropriate, and tremendously costly. Frankly, it detracts from a constructive, cooperative effort by the parties involved. These are strong negatives which characterize inappropriate legislation. Appropriate legislation and subsequent regulation, which is realistically conceived and practically enforced must be born of an honest desire for improvement, based on a working knowledge of common problems which are thoughtfully analyzed. Then the legislation must be written in clear concise language so that there can be little or no doubt as to its literal meaning and intent. To be practically enforced, it must be understood by all who will enforce it and by all who are subject to it. That is to say, an effective law or standard cannot be fixed or inflexible so that it cannot be tempered in human judgment. There must be an elasticity in the statute to provide for consideration of all of the relevant facts of a given situation. Such elasticity makes the compliance effort as meaningful as it can be for the time and dollars invested. Meaningful compliance requires room for common sense. Today, we in business along with our associates in government and labor, urgently need to pause, and assess our current situation. The problems arising from the 1969 Act have been intensified through the Mine Safety & Health Act of 1977. After reading the "findings and purpose" of this legislation, and by process of elimination, we should all clearly see what is and is not the purpose of the Act. 1) It is not to turn the management of private industry over to government. 2) It is not to impair the efficient operation of business. 3) It is not to reduce productivity and profits. 4) It is not to reduce national unemployment. 5) It is not to perpetuate the bureaucracy. 6) It is not to increase the tax burden on an already overburdened people. 7) It is not to increase our balance of payments deficit. 9) It is not to replace management/labor relations in working together to solve problems.

Jan 1, 1981

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,&apos; a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By P. Somasundaran, G. E. Agar

The role of calcium, phosphate, and fluoride species in determining the zeta potential of apatite in aqueous solutions was investigated in this study. The zeta potential of apatite was determined by streaming potential measurements over a wide range of concentrations of potassium nitrate, calcium nitrate, potassium dihydrogen phosphate, and potassium fluoride solutions at various pH values. While the addition of phosphate made the apatite surface more negative at all pH values, calcium caused a significant increase of the zeta potential only when the zeta potential was negative. Fluoride addition had only a minor effect on the zeta potential, but both negative and positive values were increased.

Jan 1, 1973

By W. L. Honnold

AS BOTH South Africa and diamond mining are unfamiliar subjects it seems best that on such an occasion as this I should endeavor to reflect the atmosphere of the place and to picture the mines from an industrial rather than from a technical standpoint and, because of long absence, my remarks must necessarily be sketchy and in some particulars not up to date. The preferable route to South Africa is via England, direct steamers from America being inferior as to service and effecting no saving of time. The newer boats are of about 20,000 tons capacity and very comfortable. Seventeen days are required for the voyage and only one stop is made-that at the island of Madiera, three days out. Between Southampton, the port of departure, and Madiera the weather may be warm or cold and the

Jan 1, 1925

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author&apos;s reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie&apos;s remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie&apos;s main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

The year 1934 saw a very thorough and intensive search for oil in Italy, both by the Government-subsidized company, the A.G.I.P., and by the few smaller operating companies. Approximately two-thirds of the exploration work, however, has been done in the Province of Emilia (northern Italy). The A.G.I.P. has been particularly active in the Emilia district and has sunk several rotary holes between Voghera and Ferrara on structures located by geophysical means in the Po Valley. Only insignificant amounts of oil have shown up in these tests to date but gas has been found in fair quantities, and apparently the company is not yet prepared to abandon its search in this part of the country without further effort. In Central Italy, the same company has put down four tests with cable tools and of these two were "dry holes" and the other two found only traces of oil. The A:G.I.P. also sank two wells in southern Italy and it is believed that in these the indications were sufficiently encouraging for the exploration work to be continued. No serious drilling has yet been done in Sicily by the A.G.I.P. or any other company. The annual subsidy granted to the A.G.I.P. by the Government for the duration of its five-year plan has been considerably reduced for 1935 and this may interfere with the completion of the coming year&apos;s program in all its details. The Società Petrolifera Italians, which is the chief producing company in the country, has continued the development of its two fields, Salsomaggiore and Vallezza, and at the same time has intensified its program of exploration. Rotary machinery has been introduced and is undergoing a thorough trial, and prospects of finding new pools at greater depths are considered good. The charcoal adsorption plant at Vallezza has operated satisfactorily throughout the year and has produced nearly 3000 bbl. of high-grade gasoline. Besides the exploration well at Rile dell&apos;Olio, which is still drilling, another wildcat test has been started at Torre-di-Traversetolo. All operations of this company are confined to the district of Emilia. The Società Petroli d&apos;Italia has continued to operate the old fields of Montechino, Gratera and Velleja, and has a well now exploring at greater depths in that general area. Of the two exploration wells in the Torino

Jan 1, 1935