Search Documents

By W. H. Bassett, J. C. Bradley

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. 11 is suggested that the materical is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the shad. Figures 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent. Structure of Protuberances The segregation of oxide between grains in the interior of the cast bar, not far from the "set," is shown in Figs. 5 and 6. In general, the amount of cuprous oxide begins to increase at a point about 0.01 in. below the normal surface of the casting, i. e., the base of the drop; but it does not attain maximum concentration in the main body of the metal. Vertical sections, Figs. 7 to 12, show that there is a definite line of large cuprous-oxide globules at the base of the drops. Horizontal sections at this place show that these large globules lie in a thin billowy

Jan 1, 1926

By R. M. Brick, Arthur Phillips

The Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segregation. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute concentration, with a resultant normal segregation or coring effect during freezing. Theoretically, musion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions aluminum-copper alloys segregate inversely and aluminum-magnesium alloys segregate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By Robert T. Howard, Morris Cohen

THE purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature trans- formations have been summarized recently by Troiano and Greninger.1 Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation [(M,)] during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transfoi mation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metallographic3 and dilatmetric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Steward7 have shown that the Greninger-Troiano metallographic techniques may be used not only for [M,] determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below [M,] in fourteen commercial steels. In the present paper, the Greninger- Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M,, thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. EXPERIMENTAL DETAILS Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M, temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1947

By Charles S. Barrett, Robert F. Mehl

A study of the structures arising from the decomposition of the ß solid solutions in the Cu-Zn and the Cu-A1 systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution— the Widmanstätten structure—-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the ? phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series—that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-—which at present seems the only a1ternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the ß and in the precipit'at.ion of the y phase from the y in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point, of view.

Jan 1, 1931

By K. E. Brown, J. P. Brill, T. C. Doerr

A wide range of intermittent gas-lift tests way conducted in a 1,500-ft experimental well through 11/4- and 11/2-in, nominal size tubing. The well was equipped with two gas-lift valves, four Maihak electronic pressure transmitters and surface facilities to measure casing and tubing pressures, temperature, liquid production and the rate and volume of gas injected. For each tubing size, tests were conducted varying the slug length, gas volume injected and liquid viscosity and surface tension. From these tests, an empirical "fallback" or liquid loss correlation has been developed. No general fallback correlation could be obtained, and the correlation is presented in the form of one curve for each slug length of a given liquid and lubing size. A conceptual model has been developed which combines the fallback correlation with equarions which govern liquid slug pow. A mathematical simulation of the model in the form of a digital computer program is used to calculate total recovery, gas volume used and clearance time for a given test. Tubing pressures at the gas-lift valve and at the gm-slug interface are calculated as a function of time. Tubing pressures at the surface during slug clearance ore also calculated. The results compare favorably with the test data and verify the conceptual model. The extent to which the model can be used for other tubing sizes, depths, liquids and gas-lift valves can only be determined with additional experimental data. Data are also necessary so that a fallback curve can be constructed for the particular test conditions studied. INTRODUCTION The flow of liquid slugs in vertical conduits has long been an established production method in the petroleum industry. Under the name "intermittent gas lift", many advances have been made in engineering design. However, the unsteady-state nature of liquid slug flow has discouraged attempts to describe the problem analytically. The result has been that intermittent gas lift is dominated by rules-of-thumb engineering practices developed over many years. The advent of slim-hole completions has increased the demand for a more rigorous solution to the intermittent problem. Small-diameter conduits offer more frictional per intermittent cycle. Small-diameter conduits are defined to be 1%-in. nominal size tubing or smaller. When oil is produced from the reservoir in which it is found, and transported to surface tanks by intermittent gas lift, three separate flow stages are encountered: flow of the fluids to the wellbore through a porous medium, vertical flow of a liquid slug from the point of gas injection to the surface, and horizontal flow of the liquid slug through the surface flowlines from the wellhead to the surface tanks. The three stages are depicted schematically in Fig. 1. The present study deals with liquid slug flow in both the vertical and horizontal conduits, ending when the bottom of the liquid slug reaches the surface. Due to the large number of variables involved, the analytical study of intermittent gas lift is extremely complex. The possibility of flow regimes other than slug type, the nature of the force fields acting on the system, the interfacial instabilities involved, the varying operational principles of existing gas-lift valves and the complete unsteady-state nature of the physical phenomena occurring in an intermittent gas-lift cycle relate some of the difficulties encountered.

By Meissner, C. A.

THE tendency all over Europe, just as it is with us, is to go to the use of turbines for new construction or replacement of old steam or even gas engines. 'The lower construction cost and the lower operating cost, when they can have high steam temperatures and pressures, together with their efficiency, is the cause of this change to turbines, both high and low pressure. The present trend is to equip plants with modern, efficient steam boilers, turbines, etc., and gradually work into high-pressure superheated steam equipment to accomplish a saving. One company has just completed a 375 to 400 lb., 700 deg. superheated steam installation and turbo-blowers with this end in view. Some of our new steam plants are using 350 lb. working pressure.

Jan 1, 1928

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By Nicholas J. Grant, Ernest P. Abrahamson

IN recent work, Bloom and Grant' and Stein and IGrant' have indicated that a high temperature chromium phase exists. In the 68 pct Cr-Ni binary they found a eutectoid reaction, P chromium transforming to a chromium plus y nickel at 1215°C. Un-

Jan 1, 1957

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

Experimental work on the properties of high-purity alloys of the copper-man-ganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. Previous Work Heuslerl conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilib- rium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alpha-beta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350' to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur6 have also noted this precipitate. Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By AIME AIME

AN unusually interesting meeting devoted to the discussion of the ways and means of improving coal mining practice, through the larger use of machinery underground, was held in the Auditorium of the Engineering Societies Building on March 11. The meeting was organized by the Materials Handling Division of the A. S. M. E. and held under the auspices of the Metropolitan Section of that Society and the National Coal Association. The New York Section of the A. I. M. E., which had been invited to participate, found itself unable to do so formally because of a conflicting date for its March meeting but informally did its part to aasure the success of the meeting. As a result of the discussion at and preceding the meeting, the National Coal Association, through Walter Barnum, chairman of its research committee, has asked the A. S. M. E. and A. I. M. E. to join the Association in a study of the present problems of the bituminous coal industry. Messrs. Harry L. Gandy, Calvin W. Rice and H. Foster Bain have been selected to act as a committee which shall develop plans for a joint program.

Jan 1, 1926

By Don M. Jackson, Robert W. Howard

Techniques for the epilaxial growth of single -crystal silicon carbide films on silicon were developed. The vapor-phase decomposition and bydrogen reduction of silicon tetrachloride (SiC14) and Propane (C3H8) resulted in clear films of silicon carbide, lip to seveval microns in thickness. The growth took place in a horizontal . silicon epilaxial reactor at 1100°C (pyrometer) at a rate of- 3000Å per minute. Electron diffraction and X-ray diffraction studies demonstrated that the films were single-cyrstal, ß -phase, or cubic silicon carbide. SiO2 film were used to mask areas of the silicon sur-lace in order that the silicon carbide might be grown in controlled geometries. Both n- and p-type films were grown on p-type silicon waters.. Heavily doped silicon films of the same conductivity type as the silicon carbide films were deposited over the silicon carbide in order to affect better probe contact to the structures. when n-type silicon carbide mesas were grown on p-type silicon substrates the de vollage-current relationships between films and substrates were that of junction diodes. These diodes showed a sensitivity to while light ill that the incident light increased forward- and reverse-satro,ation currents, P-type silicon carbide mesas grown on p-type silicon were ohmic rather than rectifying in their voltage -current relationship. No conclusions could he reached concerning heterojunc-tiou rectification in the structure. SILICON carbide is a semiconductor with many interesting properties. It decomposes at temperatures above 2200°C.1 It occurs in two general crys-tallographic forms—hexagonal (a Sic) and cubic (ß Sic)—with the cubic form having a forbidden-gap energy of 2.32 ev and the hexagonal form (specifically the 6H polytype) a gap energy of 2.86 ev.3 It behaves as an extrinsic semiconductor at temperatures approaching 5003C. It has been shown to have a high resistance to radiation damage4 and p-n junctions formed in Sic have been shown to radiate visible light under forward- or reverse-bias conditions. Epitaxial silicon carbide on silicon carbide has been successfully grown through the use of a variety of techniques, such as gaseous cracking of SiCL4 and CC4, nearly all of which require a deposition temperature above 1500°C.6 This paper will cover very recent work on the gas-phase deposition of highly ordered films of silicon carbide on high-quality silicon single-crystal substrates. The films have been shown to ex- hibit junction-rectification properties when geometrically isolated regions are electrically biased with reference to the silicon substrate. There will be no discussion of the mechanism of heterojunction rectification, but the methods of film fabrication, geometry control, and structural evaluations will be covered in detail. Electron diffraction, X-ray diffraction, and diode electrical properties were used to characterize the films and the junctions. GAS-PHASE DEPOSITION OF Sic The techniques for the deposition of silicon carbide films were a logical outgrowth of the standard silicon epitaxial process. The major premise followed was that, for any film to nucleate in an ordered fashion where there is considerable mismatch in lattice parameters (in this case 22 pct), an extremely clean, damage-free substrate surface must be presented to the gas stream. Thus a standard gas-phase HCl etching step was used to prepare the substrates for growth. A minimum of 5 µ of substrate-surface material was removed prior to the deposition of Sic overgrowth films. The techniques used for growing silicon carbide films were those of growing silicon alone, with the added injection of a hydrocarbon gas into the hydrogen and silicon tetrachloride gas stream. The hydrocarbon gases used thus far have been research-grade (99.99 pct) methane (CH4) and propane (C3H8). Propane ultimately gave the best results. The gas flows were controlled through a panel shown schematically in Fig. 1. A hydrogen main stream of 30 liters per min passed through the horizontal quartz-tube epitaxial reactor, while SiC14, C3H8, HC1, and doping gases were injected as side streams. The

Jan 1, 1965

By Walter W. Bradley

FOR a number of years up to the economic setback of the 1929-1931 period, the greatest proportional advances in the mineral industries in California were made among the substances in the nonmetallic groupings, particularly among the so-called industrial minerals and the salines. During the past year or two, although these have not regained the stride that marked their progress in the preceding decade, we can still record, -some new developments. California produces annually between 55 and' 60 different minerals on a commercial scale. Of these, some 40 to 45 comprise the "structural," "industrial," and "salines" materials as grouped in the reports of the State's Division of Mines. Barite-The barite deposits of California were described in Report

Jan 1, 1935

By W. J. Keep

We have shown in former papers the influence which aluminum exerts when added to cast-iron, and we have presented in another paper, accompanying this one, the physical properties of the metal aluminum and of some of its alloys. The present paper continues the investigation. The reader will find, in our paper on "Aluminum and Other Metals Compared,"* explanations not here repeated, which will render the diagrams in this paper intelligible. The scale of stresses is laid off on the ordinate which rises from the zero-point of the diagram. The scale of deflections is laid off on the abscissa which runs horizontally through this zero-point. By applying a given amount of stress, then running back to zero, and again applying the same stress, we describe a spring-line, in which the deflections are proportional to the stresses. Generally the deflections exceed this proportion during the original application of stress; and the excess is the permanent set. By laying off from the zero-point a line parallel to the springline, we shall generally find that this new spring-line and the diagram coincide for some distance; that is, that the test-bar is

Jan 1, 1890

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970