Search Documents

[ ] Granville S. Borden (Mining Taxation, P. 1049) has written two other published articles on the subject, Taxation and Mineral Resources, and An Income Tax Program for Mineral Producers. Both articles appeared in Mining Engineering. He is presently employed by Standard Oil Co. of California as a special tax counsel. He holds an LL. B and an LL. M from George Washington University and a Bachelor of Science in Mining from the University of California. He has been chairman of the Taxation Committee of the Minerals Economics div. of the AIME. Borden fishes, plays golf, prospects, and performs mineral analysis as hobbies. [ ] Charles C. Towle (co-author, Uranium Deposits of the Grants District, New Mexico, P. 1037) graduated from the Colorado School of Mines with a degree in Geological Engineering. He was a member of Sigma Nu; Theta Tau, an honorary professional society; Blue Key, honorary social society; the glee club and quartet, and a member of the student council. He has been a mucker, driller, flotation operator and mill shift boss for the Clear Creek-Gilpin Co., Idaho Springs, Colo.; Geologist, chief engineer, and chief geologist for Patino Mines & Enterprises Consolidated, Inc., Bolivia; appraisal engineer and part-time geology student, Denver; office geologist for Geology Dept., special Engineering div., Sea Level Canal Studies, Panama Canal; and geologist, div. of Raw Materials, USAEC, Grand Junction, Colo. He is currently chief of the Denver Exploration Branch, div. of Raw Materials, USAEC, Denver. Towle was at one time a tournament golfer, playing three and four times a week. While working in South America he played in numerous tournaments. Today, although playing only occa sionally, he shoots in the low eighties.

Jan 1, 1952

By J. E. Owen

EXPERIMENTS on twenty-six drilling muds were carried out in an effort to establish a correlation between the apparent viscosity values for these muds as obtained with the Marsh funnel and the Stormer viscometer. This required a calibration of both instruments in which the density of the calibrating liquids was taken into account. Corresponding to the Marsh-funnel viscosity values that were obtained at 1500 c.c. in, 1 qt. out, equivalent Stormer viscosity values were obtained at a Stormer cylinder test speed of approximately 1100 r.p.m. Further, a linear relation between the logarithms of the Stormer cylinder test speed and the resulting apparent viscosity was found to exist for the muds tested for 200 to 1000 r.p.m. The significance of the slope of this linear relationship is discussed as it applies to the field use of drilling muds. It was concluded that Marsh-funnel viscosity measurements are expressible in absolute units that may be correlated with Stormer viscosity measurements, provided these are made in the manner described in the paper. INTRODUCTION The Marsh funnel is used almost universally to determine the viscosity of drilling muds in the field. The Stormer viscometer is commonly used to determine the viscosity of drilling muds in the laboratory. With the Marsh funnel, the time required for one quart of mud to flow out of the funnel originally filled with 1500 c.c. is often taken as the measurement of viscosity. With the Stormer instrument, drilling mud is tested at a cylinder speed of 600 r.p.m. and by means of calibration data the apparent viscosity is expressed in absolute units. Neither of these instruments is an absolute viscometer, and apparent viscosities obtained with either are influenced by the arbitrarily standardized conditions under which the measurements are made. It is disconcerting to the man in the field to be told that laboratory measurements of the viscosities of a group of muds differ widely, when he has already observed that they have identical viscosities when tested in the Marsh funnel. Drilling muds are not perfect fluids, therefore it is not surprising to find a lack of correlation between the apparent viscosity of a mud as determined with the Marsh funnel and that determined with the Stormer viscometer. The work described here was undertaken to develop a correlation between Marsh-funnel and Stormer viscosity measurements. To a considerable degree this has been accomplished. This study has resulted not only in a better understanding of the two viscosity instruments and the data obtainable from them, but has given considerable information regarding the viscosity characteristics of drilling muds. EXPERIMENTAL PROCEDURE Calibration of Harsh Funnel and Stormer Viscometer The first step in the experimental procedure was the calibration of the Marsh funnel and the Stormer viscometer with

Jan 1, 1941

By H. E. Rorschach

Oil-field activities in Oklahoma made 1936 the best year since 1930. Approximately 2800 wells were completed, an increase of about 20 per cent over 1935. Purchasers' reports filed with the Corporation Commission showed a total of 200,240,252 bbl. of oil purchased from leases in 1936. The assembly of a complete table of the oil fields of the state was not achieved, as many of the early records of operators and pipe-line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. The outstanding developments of the year were: the discovery of rich Wilcox-sand production in the Moore pool; the spectacular drilling campaign in the Capitol or Mansion extension in the Oklahoma City pool; the surprising extension of the Olympic pool and the Hunton lime zone in the Fitts pool; and the failure to find more Ordovician production in southern Oklahoma. Wildcat discoveries, which were on a par with 1935, resulted in the discovery of such promising pools as Billings-Wilcox, North Bethel, North Earlsboro and North Lucien. The Fitts-Upper Simpson, Edmond, Jesse, Keokuk Falls and South Burbank pools underwent considerable development. Fitts Pool.—The Fitts area in Pontotoc County was greatly extended during the year and was the leader in drilling activity in the state. The producing limits were pushed to the east and north and the development of the Hunton lime horizon was outstanding. In the Upper Simpson zone 162 wells were completed; 137 in the Hunton lime zone and 26 in the Wilcox zone. The Oil Creek zone, a sand body below the Wilcox member, was discovered by the Magnolia-Statler No. 3 well located in the 1/4. 1/4 of sec. 28-2N.-7E. Moore Pool.—The Moore pool, in Cleveland County, which was opened in 1935 by the Sinclair Prairie-Franklin Community No. 1 well, surprised the oil industry when the Sinclair Prairie-Marvel No. 1 well, on Apr. 1, 1936, discovered a rich body of Wilcox sand below the distillate

Jan 1, 1937

By A. W. Ashbrook

There are essentially three main classifications for extractants: acidic, basic, and neutral. The acidic and basic are also referred to as cationic and anionic, respectively. Some extractants are shown in Table 11-1. Acidic Extractants Acidic extractants which are of use, because of cost and/or insolubility in water, are alkylphosphoric, sulphonic, aliphatic monocarboxylic acids and naphthalene derivatives.

Jan 1, 1978

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

By Samuel Hoyt

This paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by vow Gomperz,l was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disc floats on the melt, and is provided with a central hole about 1 min. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started. The capillary brings up a small quantity of molten metal with it to a point just above the lava disc. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a -small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By Robert H. Richards

The group of four papers on ore dreseing read at the Butte meeting, all of them dealing with the recent developments at the Great Falls and Washoe plants of the Anaconda Company, form an extremely important contribution to the subject of ore dressing. It proves the efficacy of the new hindered-settling principles first brought out in a paper entitled Close Sizing Before digging' and later elaborated in a paper entitled Development of Hindered-Settling Apparatus: and it is the first large demonstration on this class of mill that has been made. It must be very gratifying to all mill men to have these papers at hand, charged with careful investigations and results pointing to the conclusions reached; the papers cannot fail to be a great help to every designer of mills and to mill men who are working on this class of concentration. The papers have dealt with their subjects so completely and have demonstrated every point from beginning to end in each case so thoroughly it leaves little for the commentator to say in the way of criticism. Therefore it seems best to him to confine himself to adding a few points of history which he believes will be interesting to the readers. Referring to the paper by Mr. Wiggin, and to the fact that the Richards hindered-settling pulsator classifier was turned down, the writer wishes to say that this classifier was the first of its kind that had ever been introduced, and since that time it has undergone great developments which he believes would overcome the difficulties encountered in the test,. In fact, there was one test made at Great Falls which with the Wilfley tables and vanners brought all the tailings down to 0.36 per cent. copper except the fine slime. Since that time, and since the classifier has been further developed, in one Colorado mill it proved a wonderful amalgam catcher, catching in all

Jan 1, 1914

By R. P. Rothwell

THE first difficulty mentioned is that in some instances two or more beds of coal separated by sandstone or slate rocks of considerable thickness in one part of a basin, are found running together in another part. Of course, we may happen to strike first the part of the basin where there is but a single seam, and in this case the bed would appear to divide into two or more branches within a short distance. Such cases are not rare in the anthracite coal-fields. I would suggest as an explanation of this phenomenon the gradual sinking of the peat-marsh-the embryo coal-bed-on one side, and the moving forward of the marsh, so that on one part of the bed the formation of peat would still be progressing, while another part, being under water, would be covered with mud and sand. Thus we have different portions of the same bed of different ages. Now if the sinking of the marsh be stopped for a time, the bed will become thicker in the portions left exposed, and if the sinking now changes in direction, so that the part that had previously gone down com¬mences to rise, we should have the phenomenon of a bed, continuous throughout, with one portion overlying another, and separated from it by rock strata. These are exactly the conditions observed in splitting beds. While one side of the lake is sinking, and the peat-marsh moving on in that direction, the other side may be rising,

Jan 1, 1873

By Milo W. Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland d Portland Cement Co.. are located- at Metaline Falls, Wash, about 128 miles north of Spokane, on the Fend Oreille river, and 10 miles, of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in the construction of the power plant, the works were not put into operation until August., 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. 1 is a, view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kanisku Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 f and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by 8 ft. in crosssection, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond was used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural -course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By A. C. Milner

In a gold standard world which possesses insufficient metal to meet the every-day needs of all, confidence becomes the vital factor, the very foundation upon which the machinery for the expansion of gold into currency, and credit, rests. The gold supply, affected by many influences, moves constantly from one point to another, but not always to that point where it is most needed. In the period 1928-1930, the combined gold holdings of the United States and France increased $1,370,936,-000, and this with new gold adding only $600,000,000 to the monetary gold stock.Theref ore, the gold stocks of other countries must have been depleted during the period by $770,936,000. This uncontrolled shifting throws the delicately adjusted instrumentalities of both credit and commerce out of equilibrium. If a given nation's gold stock shifts so as to bring it substantially below the legal reserve ratio set up against it for currency issues, the effect can easily extend to the currency issues and banking credit volume of one or more nations which may have based their gold exchange standards upon the gold stock of such nation. Thus the substitution of paper based on gold in place of the actual gold is an inflation of the currency, which carries through into an uncontrolled pyramiding upon the entire machinery of credit based on gold. In 1929 Europe, South America, Africa and Asia had overissued currency based on gold. America, Oceanica and Japan, which have not overissued their gold currencies, would in normal times require their entire present gold stocks and, as Continental Asia is largely upon a silver credit basis, from a domestic standpoint, it would appear that the gold problem is not so much one of maldistribution, as it is one of inadequate supply. It would appear that some method of increasing greatly the velocity of gold, within the safe reserve point, should be devised, or that silver, of which estimates indicate that 7,000,000,000 oz. are available for

Jan 1, 1931

By Charles R. Simcoe

It was pointed out in a recent paper'g that the initial flow stress of as-quenched martensite is very low even in an alloy steel with an M, well above room temperature. It was also shown that the high ultimate tensile strength resulted from a very high rate of work

Jan 1, 1967

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By E. H. Wells, A. Andreas

New Mexico retained its position as the sixth largest oil-producing state for the year 1937 with a total production of 38,484,630 bbl. This was an increase of 11,680,184 bbl. over the 1936 production of 26,804,446 bbl., or a gain of 43 per cent. The production for Lea County during 1937 was 35,961,056 bbl.; for Eddy County, 2,136,251 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 387,323 bbl. The average daily non-marginal well allowable for Lea County on Jan. 1, 1937, was 92 bbl.; at the close of the year it was 67 bbl. The average daily pipe-line runs were less than the allocations of the New Mexico Oil Conservation Commission, but slightly in excess of the state allowables recommended by the United States Bureau of Mines. The average daily production for the year was 105,437 barrels. The total number of completions in the state was 742, of which 638 were oil wells; 19 hydrocarbon gas wells; 5 carbon dioxide gas wells and 80 dry holes. Of the dry holes, 46 were in proven fields. Of these 46 dry holes, 13 were in the Artesia-Grayburg-Jackson-Maljamar area, Eddy County, two in the Getty Extension field, Eddy County, 11 in the Red Mountain field, McKinley County, three in the Rattlesnake field, San Juan County, and nine in the Aztec-Bloomfield area, San Juan County. There were only eight dry holes in the proven fields in Lea County. Southeastern New Mexico Lea County.—The Monument field was the largest producing field in Lea County, with 10,945,788 bbl., closely followed by the Eunice field with 10,927,929 bbl. The Hobbs field, formerly the largest producing field in Lea County, was relegated to third .place, with 7,292,522 barrels. Drjlling during the year closed the gap between the northern part of the Eunice field and the southern part of the Monument field. The wells in this area were relatively small, because of decreased porosity in the lime. The greatest activity in Lea County was in the Monument pool, with 199 completions, 197 being oil wells, one a gas well and one a dry hole.

Jan 1, 1938

By Y. C. Liu

The orientation relationship between the dejormation and recrystallization textztres of binary Cu-P alloys of high phosphorus content was observed to he a ± 14-deg (110) rotation. According to the ori-ented-gvowth hypothesis, the same relationship should exist between a successfully flowing pain and the strained single-crystal matrix of alloys of corresponding composition. The orientations of thirty successfully growing grains were obtained in a Cu-1.0 at. pct P alloy. Both a conventional analysis and the more detailed analysis advanced in the present study demonstrate that the observed orientation relationship is not comparahle to that predicted by the oriented growth hypothesis. IT has been shown experimentally that the formation of recrystallization textures in metals may be explained on the basis of the oriented-growth hypothesis. This conclusion is based primarily on the results of cooperative experiments carried out by various investigators in aluminum. Beck and HU' suggested that the orientation relationship between the recrystallization and deformation textures of aluminum is a 38-deg(111) rotation. A similar relationship, i.e., a 40-deg(111) rotation, was observed between the primary and secondary recrys-tallization textures.' Since the secondary grains result from a process of selective growth, this naturally implies that the same mechanism is also responsible for the formation of the primary re-crystallization texture from the deformed matrix. Further evidence was provided by the experiments of Liebmann, Liicke, and Massing3 and Yoshida, Liebmann, and Lucke.4 They observed that grains which could successfully grow into strained aluminum single crystals invariably exhibited the same orientation relationships with their matrix. Thus, regardless of other opinions,5'9 these results offered good evidence in favor of the oriented-growth hypothesis. In order to examine broader applications of this oriented-growth hypothesis, experiments should be carried out in metals other than aluminum. In a recent investigation on the recrystallization textures of binary copper alloys with phosphorus, arsenic, and antimony,7 it was found that the predominant recrystallization components were related to the deformation textures by a (110) rotation. The (110) rotational relationship is different from the (111) relationship generally proposed between the recrystallization and deformation components of other binary copper alloys. 1,8,9 Applying the observations made for aluminum, the oriented-growth hypothesis predicts that the orientation relationship of grains successfully growing into the strained single crystals of either one of these copper alloys should correspond to that observed in the textural study. Verification of this prediction would provide a critical test of general applicability of the oriented-growth hypothesis to the formation of recrystallization textures in fcc metals other than aluminum. The Cu-1.0 at. pct P alloy was selected in the

Jan 1, 1964

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

but, returning to South Africa, for the next two years he was assistant general manager of the Simmer Deep Gold Mining Co., at Johannesburg. In June, 1911, he returned to New Zealand as general manager and consulting engineer for the Consolidated Goldfields of New Zealand, at Reefton, which position he held at the time of his admission to the Institute in 1914. Early in September, 1915, he left New Zealand for active service in France. Corporal Sheppard B. Gordy Sheppard B. Gordy, born in Ansonia, Conn., in 1889, graduated from the Sheffield Scientific School in 1910 and with the degree of E. M. in 1912. He entered the employ of the Braden Copper Co. immediately on his graduation and remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time he had gone to Dayton, Ohio, to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9. Lieutenant Thomas Clarence Gorman Thomas C. Gorman, a lieutenant in the Second Tunnelling Company of the Canadian Engineers, was killed in France on Mar. 18, 1918. He was resting in his sleeping hut and was in the act of writing a letter when a bursting shell killed him.

Jan 1, 1920

but, returning to South Africa, for the next two years he was assistant general manager of the Simmer Deep Gold Mining Co., at Johannesburg. In June, 1911, he returned to New Zealand as general manager and consulting engineer for the Consolidated Goldfields of New Zealand, at Reefton, which position he held at the time of his admission to the 1nstitute in 1914. Early in September, 1915, he left New Zealand for active service in France. Corporal Sheppard B. Gordy Sheppard B. Gordy, born in Ansonia, Conn., in 1889, graduated from the Sheffield Scientific School in 1910 and with the degree of E. M. in 1912. He entered the employ of the Braden Copper Co. immediately on his graduation and remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time he had gone to Dayton, Ohio, to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9. Lieutenant Thomas Clarence Gorman Thomas C. Gorman, a lieutenant in the Second Tunnelling Company of the Canadian Engineers, was killed in France on Mar. 18, 1918. He was resting in his sleeping hut and was in the act of writing a letter when a bursting shell killed him.

Jan 1, 1920

By H. I. Smith

The technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe there is accord, I will distinguish between booster and auxiliary fans. Definition of Booster and Auxiliary Fans In discussing underground fans G. S. Rice1 distinguishes between those used to increase the amount of air passing a given point and those used to augment the ventilation locally. He describes a booster fan as one which is installed to handle the entire air current passing a given

Jan 1, 1927

By Dwight Farnham

Description of Quarry THE shale used at the Renton plant of the Denny-Renton Clay Coal Co., for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated. The shale deposit, which is of unknown thickness pitches about 10° to the southeast. The 150-ft. face worked extends approximately east and west, so that the clip, as shown by the photograph, is to the left and into the hill. The shale is overlain with about 50 ft. of gravel, 70 ft. of clay, and 30 ft. of mixed loam and gravel, making altogether from 125 to 150 ft. of overburden. Disposal of Overburden The overburden is removed by sluicing. For this purpose a No. 2 Joshua Hendy giant is used, throwing a 12-in. stream', and having 60 lb. pressure at the nozzle. The water is drawn through an 8-in. pipe from Cedar river, about 1,000 ft. distant, by means of a Worthington four-stage centrifugal pump, direct connected with a 100-h.p. motor placed just south of the factory, and 1,500 ft. from the nozzle This plant handles the material satisfactorily to a height of about 75 ft. above the level of the top of the shale. When the higher levels are worked, an auxiliary plant consisting of a four-stage Byron Jackson centrifugal pump with a 100-h.p., belt-connected motor, is thrown into the system. This plant is situated on top of the shale and can be discerned at the extreme right of the trestle work in Fig. 1.

Jan 9, 1914

By AIME AIME

WHEN Vice-chairman Calvert Townley calls the next meeting of the Executive Board of the American Engineering Council of the Federated American Engineering Societies to order in Washington on Sept. 30, it will be the first meeting in that city for almost a year. It is probable that the Board will decide at this meeting whether future board meetings will be held regularly at the headquarters in Washington or whether the plan of meeting at various engineering centers throughout the country, as has been done during the past year, will be followed. The most important business coming before this .meeting will be the election of a president to succeed Herbert Hoover, who resigned after he became Secre¬tary of Commerce. Nominations to fill this vacancy were ordered 'at the last meeting of the Executive Board, to be reported at the September meeting. Special attention will be given the plans for the engineering assembly, extension of employment service, question of licensing and registration of engineers. The engineering assembly, committee has been appointed, with A. P. Davis as chairman, the other members being Philip N. Moore, L. P. Alford, John C. Hoyt and F. A. Vaughn. This committee will work out detailed plans for an assembly to be held in con¬junction with the annual meeting of the American Engineering Council in, January. Tentative plans provide for a three-day session; one day to be given to special meetings of the executive boards of member organizations and committees of the American Engineering Council; one day to the sessions of the American Engineering Council; and at least one day to discussion of some, special topic.

Jan 1, 1921