Search Documents

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By S. M. Wu, R. L. Stone, T. D. Tiemann

The dissolution of silica from quartz in sodium hydroxide solutions was investigated by statistical methods. A second-order predicting equation was developed with 28 experiments expressing the dissolution of silica as a function of the variables quartz size, time, temperature and sodium hydroxide concentration. With this equation a comprehensive picture of the dissolution reaction was gained which included the effect on extraction of each variable and their interactions, fractional extractions, reaction rates and activation energies. A previous investigation of the extraction of silica from low grade siliceous iron ore by digestion in sodium hydroxide solutions presented the extraction as a function of time, temperature and sodium hydroxide concentration.' The present paper is an outgrowth of the previous work and develops by a mathematical analysis the functional relationship between the extraction of silica and time, temperature, sodium hydroxide concentration and particle size. Relatively pure quartz was used in this study in order that the basic quartz-sodium hydroxide reaction could be studied without the influence of other constituents that are commonly found in iron ores. The functional relationship between the dissolution

Jan 1, 1965

By James R. Walpole

This paper will discuss the federal laws and regulations that are related to water quality. Both surface and underground water quality issues will be covered as well as point and nonpoint source requirements. Some of the subjects to be covered include the Federal Water Pollution Control Act (e.g., effluent guidelines, nonpoint source requirements, etc.), the Safe Drinking Water Act (e.g., underground injection control requirements; pits, ponds, and lagoons study, etc.), the Resource Conservation and Recovery Act (e.g., mining wastes study, etc.). The importance of related court decisions will also be discussed

Jan 1, 1982

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By George Wolff

To THE average person, the purport of the items and figures on the balance sheet of a mining company are hazy and the real financial condition of the company is cloaked in obscurity. It is also likely that the satisfaction of the stockholder in his investment, as well as the determination of the prospective investor, rests more on the reputation of the company, his confidence in the management, the stated earnings per share and the dividends paid, than on a comprehension of the information contained in the balance sheet. The balance sheet of any company at best can only closely approximate the true financial condition as of a given date. Any item of asset, except cash, can probably be altered if another's viewpoint is applied. It is difficult and expensive to drill and explore an orebody to determine the entire tonnage of ore therein. Those inherent difficulties render it practically impossible to prepare an absolutely correct balance sheet of a mining company. It is possible, however, to present the facts of a mining company more intelligently and comprehensively than is usually done. With this in mind, a balance sheet of an imaginary mining company is submitted, with supporting schedules. The same fundamental principles hold true whether we consider a large or a small company. Less complexity is involved in dealing with the affairs of a smaller company. Therefore, for this purpose, the assumed company operates but two mines and a smelting plant. It has been deemed advisable to introduce the features of the operation of a mine acquired prior to March 1, 1913 and one after that date. The presentation therefore is concerned in one mine with the appraisement as of March 1, 1913 and in the other with the appraisement by reason of discovery. A consequential factor pertains to dividends paid from depletion reserves and therefore free of surtax to the stockholders. While supporting schedules, when necessary, give details of certain items on the balance sheet, it seems desirable to give further explanations with respect to some of them. This seems to be important because some mining companies do not treat the items as indicated on the statements submitted.

Jan 1, 1928

By H. I. Aaronson, H. A. Domian, G. M. Pound

The thernodyna,nics of I the Proeutectoid ferrite re-action ha1.e been investigated on the bases of three diifevent descviptions of the statistical thernzodynamics of interstitzal solid solutions. Especially at low ternperatures, substantial dijeretzces are found in the valltes of the extrapolated y/y + a and cr/a + y equilibriurn curls, and in the To- co7nposilion metastable eqliilibriunz curl-es thus co,npited. Although neither actiztity nor phase-diagram date are able to distingrish udeqiutely among the various descviptions, the statustics of Lacher, Fouller, and Guggenheinz provide the ?nost conplete epresentation az3ailable of the single carbon-ctrbon interaction energy (w) nzodel of an intevstitiril solid solution, and the relationships deduced frojrl then2 are accordingly pre.ferred. The findings tlzut w in austenite 'aries significu?ztly uith tenpevntrue and that phase-diagawr data arc not accurately con?palible usith eqcrctions deduced on the basis of actility infoation indicate, hou'e13er, that a wzore cornplex nlodel of the uustenite , und pvobably of the .feyrite, solirl solutions will have to forn the basis of f4tuve statistical t1.eat1nents. Some suggestions for such a ruodel arc advanced. Althoug11 w represents a vepltlsio energy in austozite, it was found to corvcsporzd in ferrite to a binding energy, in qualitatit.e accord zc,itlz the internal-friclion results of Keefer and wert. ThE transformation of austenite to proeutectoid fer-rite is becoming recognized as an exceptionally useful vehicle for quantitative studies of the kinetics of phase transformations.'" Reasons for this popularity include well-characterized microstructures which develop on a convenient scale with acceptable kinetics within a considerable temperature-composition region, the absence of great sensitivity to common impurities, and, especially. the availability of a unique wealth of the ancillary information indispensable for the quantitative interpretation of kinetic measurements, including phase diagram,3 crystallographies diffusivity,5 inter-facial energy,=17 elastiit," specific vlume, ''' and ativity'-' data. Development of considerable amounts of additional thermodynamic information from activity data is of particular importance with respect to kinetic studies, since much of this information is needed in temperature-composition regions not directly accessible to presently available techniques for the measurement of equilibrium properties. A generally useful approach to the thermodynamics of solid solutions, which is of especial value in this situation, is based upon the formulation of the free energy of such solutions as a function of temperature and composition. The free energy of solid solutions has been resolved into many components. Particularly in the case of interstitial solutions, with which we shall be concerned in the present study, however, only the positional entropy component has been intensively studied. The other components are conventionally taken into account by fitting equations for the activity of the interstitial species or the temperature-composition path of phase boundaries, derived principally from positional entropy considerations, to experimental information on these quantities through adjustment of one or more constants in the equations. A number of studies of the thermodynamics of interstitial solid solutions have been made primarily on this basis,'"25 but only Kaufman, Radcliffe, and cohenZ2 (hereafter KRC) and ener''% ave applied the results of such studies to develop relationships for the thermodynamic quantities of interest in the austenite —- proeutectoid ferrite transformation. KRC made use of a model developed by cheil'' (on the basis of a previous study by ohansson'), and subsequently rede-rived correctly by Speiser and retnak,' in which a carbon atom is considered to inhibit occupancy of a certain number of its nearest-neighboring interstitial sites. schei120 determined the number of sites in austenite thus excluded by matching calculated and experimentally measured curves for the variation of carbon activity with the mole fraction of carbon. zener17 used a different approach. He assumed that the positional entropy of carbon is ideal both in austenite and in ferrite (i.e., no excluded interstitial sites), and included all other contributions of carbon in a temperature-independent "free-energy change" accompanying the transfer of 1 mole of carbon between the two phases. This quantity was determined by "pinning" an equation derived for the boundaries of the a + y region to experimental data on the compositions of these boundaries at a single temperature. In the present investigation, three different approaches to the thermodynamics of the proeutectoid ferrite reaction are examined comparatively: I) the method of Zener; 2) the model employed by KRC and predecessors; and 3) the more detailed statistical thermodynamic treatment of the same model developed by acher and Fowler and uenheim, ' in which the problem of overlapping regions of influence of individual interstitial atoms is resolved. In order to make these comparisons, it is necessary to undertake an extension of one aspect of Zener's method; since the Lacher- Fowler -Guggenheim (LFG) treatment has not been previously used in the present context, the necessary thermodynamic "superstructure" for this treatment will be developed in parallel

Jan 1, 1967

By K. L. Komarek

Based on theoretical and experimental evidence a discussion follows of the behavior of phosphorus -bearing iron ores in the R-N Direct Reduction Process and suggestions are made of methods of reducing the amount of phosphorus in the metallic end product. In ferrous metallurgy a direct reduction process is one in which iron ores are reduced to metallic iron with gaseous or solid reductants without the appearance of a liquid phase. A number of attractive features have induced several companies and government agencies to invest in the development of direct reduction processes. A summary of all direct reduction processes up to 1954 has been given by Barrett,' and Wiberg,2 and Willems3 have reviewed the most recent developments in this rapidly expanding field. Many difficulties have been encountered in direct reduction processes and the nature of these difficulties has varied from process to process. One problem common to almost all of them is the removal of phosphorus which is one of the reasons for the rather pessimistic outlook given by some government publications4'5 to direct reduction processes. In this paper an attempt is made to give a theoretical explanation of the variations in phosphorus removal observed in the R-NY Direct Reduction Process. However, many conclusions are general enough to be applicable to other processes. Most iron ores treated by the R-N process yield products lower in phosphorus than the original ore. A qualitative account of the factors has been given by Stewart, Reed, and Herasymenkoe but the erratic removal of phosphorus from some ores and the general importance of this problem make a more careful analysis of the theoretical aspects desirable. In the R-N process mixed ore or balled fines, ex-

Jan 1, 1963

By C. D. Broadbent

INTRODUCTION The slope stability research plan at Kennecott was developed to serve the specific needs of large, open pit mines; primarily those developed in faulted and highly-fractured intrusive deposits. The program emphasis is on applied research; being defined in this case as research into the engineering mechanics of discontinuous rock and into the related rock property survey and slope design techniques. The program has been developed in phases, with each phase organized to explore more thoroughly the most significant findings of previous work and to improve on techniques found to be applicable. The current work is based on principles developed early in the program and that show promise of having engineering and economic value. A brief summary of the conceptual principles of the program is given to put our current work in context. This is followed by a review of the two cooperative programs done with the U. S. Bureau of Mines. Most recent work is described and interpreted in terms of practical slope design. Although failure-free slopes are a desirable goal, it is recognized that some failures will occur when overall slope designs approach a calculated safety factor of one. A discussion of failure control research is therefore offered. BACKGROUND In 1965 Kennecott management specified that a slope stability technology must be used to achieve optimum development of ore resources. The subject was carefully explored and by 1960 it had been established that there was no technology readily applicable to open pit slope design. Therefore, in 1962, Kennecott Copper Corporation and the U. S. Bureau of Mines agreed upon a cooperative research program having the objective of developing a mine slope stability science. One of the first decisions made by the cooperating groups was that the research must be conducted primarily in the field and not in the unrealistic environments of a laboratory. Accordingly, the Kimbley Pit, an abandoned mine once operated by Kennecott's Nevada Mines Division in Nevada, was selected for the full-scale research. Fortunately, there was near-universal agreement on the basic stability parameters and thus on the areas to be investigated. These parameters were acknowledged to be: (1) anisotropy (generally due to faults or joints), (2) stress, and (3) water; in that order of importance.

Jan 1, 1972

By D. Webster

It has been found that cold work and annealing treatments greatly retard subsequent grain growth and re-crystallization in thoria-dispersed nickel and NiCr. It is suggested that this is due to cavities which form at the particle-matrix interface durilzg cold work. Some of' the cavities formed are stable at elevated temperatures and prevent the mouement of large-angle grain boundaries. The movement of these boundaries at elevated temperatures is known to start recrystal-lization and when they are pinned by voids recrystal-lization is made more difficult. TD Nichro,me had a maximun resistance to recrystallization when the initial structure was coarse-grained and had a low dislocation density. A precipitation reaction occurred between 700° and 1200° F in cold-worked TD Nichrome. It has been shown by Grant and his coworkers1-3 that a large part of the strength of dispersion-hardened materials is a result of the cold-worked structure produced during fabrication. In a comparison of the strength of cold-worked copper with and without an oxide dispersion, Grant4 has demonstrated that there is little difference in strength at room temperature. The function of the dispersion is essentially to maintain the cold-worked structure at higher temperatures than is possible in the base material. The dispersion accomplishes this by making recrystallization more difficult. The mechanism by which this is achieved is discussed in this paper. The fabrication history of the material has been found to greatly influence recrystallization behavior and this aspect is discussed in some detail. I) MATERIAL Three different thoria-dispersed materials were examined. 1) DuPont 2 pet thoria-dispersed nickel (TDNi) in 0.050-in. seeet. Thoria particle size is in the range 100 to 2500A. 2) DuPont 2 pct thoria-dispersed nichrome (20 pet Cr, 80 pct Ni) (TDNiC) in 0.125-, 0.060-, and 0.040-in. sheet. In the as-received condition these sheets have

Jan 1, 1969

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

[ ]

Jan 1, 1938

By H. A. Koch, R. L. Slobod

This paper discusses a new oil recovery process called the "miscible slug process." This process involves the injection of propane or LPG into the reservoir prior to gas injection. The operating conditions are maintained so that the slug is miscible with both the reservoir oil and the injected gas phase. Thus, a miscible phase displacement is achieved, and high recoveries are obtained from the area of the reservoir contacted. The most striking discovery of the laboratory study which included displacements from cores up to 123 ft in length was that relatively small slugs of LPG are effective over reservoir distances in the miscible displacement of oil. This makes possible the commercial application of the process. The important factors controlling the size of the slug are: (I) reservoir length, (2) reservoir fluid composition, and (3) reservoir pressure at the displacement front. Of lesser importance are the effects of injection rate and porous medium type. Questions which have not been completely answered deal with the effects of gravity and reservoir inhomogeneities on the process. INTRODUCTION One of the major problems facing the oil industry today is recovery of the large fraction of the discovered oil which will remain unrecovered unless some new processes are found. Water flooding has been one successful method used to increase recovery over natural depletion. But even successful water floods may leave 25 to 40 per cent of the pore space filled with residual oil. Recently a process which involves the use of thermal energy has been reported1,'*' which may prove useful in increasing recovery from shallow reservoirs containing highly viscous crudes. This paper deals with a new oil recovery process involving use of miscible phases to displace the oil from the reservoir. Miscible phase displacement oil has been an intriguing idea because the elimination of capillary effects in the reservoir leads to 100 per cent recovery in the areas contacted by the miscible displacing phase. The big deterrent in the past to the practice of miscible phase displacement has been the high cost involved in using large volumes of solvent in the process. The use of high pressure gas to achieve a miscible phase displacement of reservoir oil has been reported4,5 as one economically feasible method. However, this process calls for the maintenance of pressures above 3,000 psi at the dis-placement front. The process described in this paper is not restricted to high reservoir pressures; the only qualification being that the slug of material which is injected into the reservoir must be miscible with both the displaced oil 2nd the displacing phase. Two such cases are the use of an alcohol slug followed by water to achieve a mis-cable water flood, and the use of a low boiling hydrocarbon slug such as propane followed by gas to achieve a miscible gas drive. This paper will deal specifically with the propane dug process. This process will obtain a miscible phase displacement at pressures as low as about 1,200 psi at a reservoir temperature 01 150°F. The process is very simple. The propane displaces oil completely at one front because it is miscible with the oil, and gas displaces the propane completely at a second or trailing front because it is miscible with the propane. A small band of propane should thus remain wedged between the gas and oil phases. This idea has been called the "miscible slug process."6 Unfortunately, the propane slug will become diluted as it flows through the reservoir. This results from a mixing action since the fluids flow through a complex reservoir porous medium rather than simple capillaries. Fig. 1 diagrams a miscible slug displacement. The effects of some of

Jan 1, 1958

By Eugene Guccione

Before answering the question raised in the title, let's briefly consider how East-West trade is viewed within the entire US political spectrum. Essentially, there are four major schools of thought: (1) The Peaceful-Coexistence School. Advocates of this school call themselves free-traders and hold to the premise that: (a) trade benefits all parties involved, hence it is the best tool to achieve peace; (b) US trade barriers should be removed, and the quicker the better; and (c) negotiations, cultural exchanges, and political compromise should be used extensively.

Jan 9, 1974

By T. Katayanagi, J. Shimoiizaka, K. Nakatsuka

Feldspar has been separated from silica by cationic collector using hydrofluoric acid as an activator of feldspar (1,2). Recently, one of the authors developed a new flotation process separating feldspar from quartz without using hydrofluoric acid. Presently, some silica sand mills are operating to introduce this process in Japan (3). In this flotation, feldspar is floated from silica using normal alkyltri-methylene diamine acetate together with sodium petroleum sulfonate as collectors in a hydrochloric or sulfuric acid circuit of about pH 2. From fundamental studies, it was found that, though the aliphatic diamine by itself did not adsorb on feldspar sufficiently to give a satisfying flotation in acidic circuit., the adsorption of collector was promoted by the simultaneous use of petroleum sulfonate and resulted in sufficient flotation of feldspar. On the other hand, quartz did not float in this flotation process. The application of this flotation was attempted for some types of natural samples and satisfying results were obtained. Further, an example of practical plant was introduced and the advantages in the process are emphasized.

Jan 1, 1976

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

By H. A. Kuhn

THE Pittsburg coal field in western Pennsylvania, is conceded to be the most important in the world. To measure its importance it is necessary to understand the extent of its service in the various industries of the country. Probably 90 per cent. of the pig iron manufactured in the United States up to the present time has been made by using coke manufactured from the Pittsburg coal seam in western Pennsylvania. This coal field is the foundation on which the city of Pittsburg rests and is the reason for the great growth of the iron industry in the Pittsburg district. Iron ore is brought to this district, not because Pittsburgh is a. natural location, over other locations, for the iron and steel industry-as its position places the manufacturer at the mercy of the railroads-but the ore is brought 1,100 miles to meet the fuel. It can be said that the illuminating-gas industry in the United States has used this coal exclusively to the same extent that the pig-iron maker has used it. It may be also said that 20 to 25 per cent. of the fuel used on railroads in the United States conies from this coal field. The Pittsburg coal field is unquestionably the center of the industrial population of the United States, for in addition to the industries of the district and those closely adjoining, it has tributary to it all the cities and industries along the Great Lakes and practically all of Canada with the exception of the extreme western and eastern ends. It supplies the industries and population west of Duluth and Superior many hundreds of miles. This coal is floated down the Ohio and Mississippi rivers, supplying the towns en route, and is delivered in New Orleans, a distance of 2,200 miles, for approximately SO to 90 c. per ton transportation cost. It is delivered on the docks of Superior and Duluth at a cost of transportation 50 c. a ton less than the cost of transporting the same coal from Pittsburg to a local consumer in Philadelphia. With other Appalachian coals it has large markets east and along the seaboard, especially for byproduct-coke making and the illuminating-gas industry. It is considered the premier railroad fuel of the world on account of the fact that this coal in a given-sized locomotive will probably haul more cars than any other coal in the

Jan 10, 1914

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981