Search Documents

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

By S. F. Shaw

MINING conditions in Mexico during the current year have been most unfavorable, synchronizing with conditions in the United States, but the outlook for the near future is improving. The chief difficulties met with are because of the following conditions: severe drop in prices of metals; high smelting rates; high prices of supplies; inadequate means of transportation; low efficiency of labor. In comparison with pre-war prices for metals it cannot be said that prices are low, particularly for silver, which recently has gone to a level that would have been considered exceedingly good in 1912. But conditions have changed so greatly that only the most favorably situated properties can operate without loss.

Jan 1, 1921

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,'-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By W. P. Rawles

In the foreword by C. K. Leith, Chairman of The Mineral Inquiry, it is pointed out that the ordinary mineral production tables do not show the commercial control, and that some knowledge of the situation is desirable as a background for the consideration of problems involving mineral raw materials. The report consists principally of tables, accompanied by a brief text, giving the production and an analysis of the control, according to nationality, of 18 minerals: aluminum, chromite, copper, iron and steel, lead, manganese ore, mercury, molybdenum, nickel, nitrates, petroleum, potash, silver, sulfur, tin, tungsten, vanadium, and zinc. For the most part, the production figures for 1929 and the latest figures for reserves have been used. When feasible, the control has been shown at the various stages of production; mining, smelting and refining. American capital was dominant in the production of 10 mineral commodities, including six of the most important; British capital, in four instances; while Spanish, German, Chilean or Chinese interests cach led in the control of one. British, French, German, and Dutch capital occupied second place in the control of most of the important minerals. Between two-thirds and three-fourths of the world's mincral production is controlled by British and American capital.

Jan 1, 1934

By AIME AIME

L. C. GRATON, professor of geology in Harvard University, addressed the New York Section on April 24 on-his impressions of the Rand. His beautifully clear and concise address was delivered without notes, so that what follows is merely a resume of the principal points made. The world is apparently coming to the end of ore discoveries easily made, yet we need metals at a steadily increasing rate. If surface discoveries are to decline, then we must find other ores or use less metals. The probable chances of finding ore are greater in the centers of big production than in new districts, as proved statistically. It is unsafe to say that a field is worked out. Therefore, deep mining holds possibilities and is an interesting study that will progressively gain in importance. The origin of the gold in the banket of the Rand has been a geologic football for a long time. Of the various theories, two have survived: 1. Infiltration into permeable conglomerate beds from deep-seated sources; 2. the placer hypothesis, which holds that gravel beds originally had the gold in them. At present, the second theory is accepted by the majority, as a result of the studies by the Union Geological Survey and by E: F. Mellor which were published about fifteen years ago.

Jan 1, 1929

By Roy McLellan

THE slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents.

Jan 1, 1930

By W. R. Davison, C. A. Brown, J. P. Carstens

INTRODUCTION The phenomenon of heat-weakening of rock with 10.6 micron radiation from a continuous-wave C02 gas laser has been investigated in detail at the Massachusetts Institute of Technology for over 5 years. The programs at MIT have explored the basic nature of the heat-weakening phenomena and rock fracture caused by heating (e.g., Refs. 1 and 2), and have resulted in quantitative estimates of the relationship between the amount and parer level of heating and the resulting decrease in the modulus of rupture of a rock beam in a three-point bend test (Ref. 3). Results of the tests reported in Ref. 3 indicate a greater than 90% reduction in the modulus of rupture for granite beams heat-weakened by a laser. These results prompted the U. S. Department of Transportation to seek an assessment of the expected feasibility of employing the heat- weakening concept in a full-scale tunnel boring operation. Present- day continuous rock-tunneling machines have demonstrated tunneling time and cost savings over drill-and-blast methods, when used in rock types that are easily broken by the cutters. However, cutter bits have not yet been developed which can easily penetrate very hard rock

Jan 1, 1971

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954

By Walter Renton Ingalls

IN SEVERAL papers and addresses during the past two years, I have dwelled upon some of the economic consequences of the war. The fundamental thought that I have sought to convey is that the world became immensely poorer by the war, not only in material wealth and population, but also in the psychology and morale of the people. I do not see how there can be any intelligent dissent from that statement. All the ideas of post-war prosperity were manifestly fallacious, manifestly fallacious from the outset. If there had been any truth in them it would have followed logically that a great war, with all its destruction of wealth, health and life would be a good thing. Therefore, let us have a great war every ten years or so. Such an idea would be both monstrous and absurd. Assuming then the acceptance of my premise, I have tried to show that the losses by the war could be made good in a short time, i.e., in a relatively short time, only by doing things a great deal better than formerly, and that the accomplishment of such a result called for greater transparency in industry, for industrial cooperation, for thinking in terms of industries as a whole, and for the greater exercise of engineering functions. All of this introduced, of course, the position and psychology of labor. I say frankly that I do not look for labor to contribute any constructive thought to the upbuilding. I neither expect it nor hope for it. This is a pity, for it could do so much for its own economic advancement if it would. However, it never has done so, but rather has benefited only from the exercise of the talents of the few, and the main hope now is to bring it into a passive state, dispelling the resistive fallacies that developed during the war. Let us briefly examine the nature of these.

Jan 1, 1921

By David Baker

IN a paper presented to the American Institute of Mining Engineers, September, 1904, entitled ? Improvements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low-thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace gases, unequal reduction, slips, scaffolds, irregular cutting of the. inwall, " off " iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from successively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very simple form of rotary distributor, which may be applied to any form of double-bell charger, retaining the perfect gas-seal, which is so admirably obtained by that construction. In seeking protection for this invention, I found no similar distributor on record in the patent offices of the various countries where application was made; but an application show-

Jul 1, 1906

By V. M. Lovell

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysaccharides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By P. V. Roundy

PUBLIC lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934,' it contained 66,796 acres, of which only a small part had been defi-nitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not he done on any considerable scale under the Survey's usual appropriations; it gave employment to unem-ployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration.

Jan 1, 1937

By AIME AIME

FEW mining engineers-noted as the profession is for migratory predilections.--can point to as varied a record as Scott Turner, director of the U. S. Bureau of Mines and newly elected vice-president of the Institute. His record as printed shows that from the time of his graduation from the Michigan College of Mines in 1904 until he went to the Bureau in 1925, he worked for 21 different companies. Geographically the record is no less imposing, although one reason for this is the fact that he was field engineer for several exploration companies. Virtually every important mining state in the Union is represented in addition to Canada, Alaska, Panama, and several countries each in South America and Europe. In addition to all of the common metals he has mined tin and coal. He opened and operated for five years a group of coal mines in 73" 13' S. Lat., on the Island of Spitzbergen. This was 825 miles north of the Arctic Circle on No Man's Land, where Mr. Turner claimed and maintained pos- session under the American flag of an area of 600 square miles. Incidentally, he was a survivor of the ill-fated Lusitania, sunk by a submarine in May, 1915.

Jan 1, 1930

By AIME

TO say that Milton Fies has been active in promoting the Southern Research Institute is a masterpiece of understatement. He is a director and trustee who was in on the ground floor when plans were first made for the Institute and since it became an actuality early in 1945 his interest and efforts continue. He talked about it at the last regional meeting of the Birmingham Section of the A.F.A. and has talked all over the South-and when he makes a speech he has really prepared it. He does not try to rival a political spellbinder, but his careful, concise English is always well thought out and to the point. Southern Research might be called his present hobby as it has been for the past two or three years. Another major interest has been his encouragement and training of engineering students. Active in the formation of the Student Chapter of the A.I.M.E. at the University of Alabama, for several years he saw to it that the students had a prominent engineer at each monthly meeting, usually taking them down to Tuscaloosa from Birmingham in his own automobile. He has also been keenly interested in the mining engineering activities at Tuscaloosa, both in the Bureau of Mines and the University.

Jan 1, 1946

By John F. Burst

GENETIC correlations of the various types of Cheltenham fireclays found in Missouri have been the subject of several papers. The correlations usually have been attempted on the basis of stratigraphic and leaching patterns (Wheeler,18 1896; Allen, 1,2 1935 and 1937; McQueen,13 1943). Herold10 (1943), as well as Allen,l,2 has dealt at length with the mineral¬ogy of Missouri fireclays and postulates genetic relationships from min¬eralogical findings. Both researchers cite kaolinite as the primary clay mineral of the Cheltenham formation and suggest that differences in physical proper¬ties are due to clay mineral impurities such as halloysite or illite (not recog¬nized by the name "illite" at the time of Allen's papers). By ascribing the differences to impurities, it is possible to use weathering as the only major alteration factor. This paper seeks to probe still farther into the clay mineral composition of the Cheltenham formation and to show thereby that the mineralogical differ¬ences that have been found to exist within the "kaolinite" component of the Cheltenham fireclay may alter somewhat the previously held theories of diagenesis. Two Missouri fireclays, which have been rather thoroughly investigated, were chosen for comparison of genetic relationship to clay mineral content. One is a typical plastic fireclay of the middle Cheltenham (McQueen's classification13) obtained at Mexico, Audrian County, Missouri, from a large open pit operated by the A. P. Green Fire Brick Co. The other-a typical hard flint fireclay-was obtained from a pocket deposit in southwestern Mont¬gomery County, Missouri.

Jan 1, 1952

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag' , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr'- -- 7H,O [1] 2Ce ' ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]' dt -LCu+' l+ (k ,/k,) [H] [3] where, K = 1x10"' exp [—26,600/RT] 1, mole-' min-' ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH' 4-HA [51 k., CUH + CU" ? + 2Cu f H' [GI 6Cu'+ Cr,07 + 14H'+ 2Cr- (¦ 7H,O + 6Cu" ['i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.'" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",' " and by Schaufel-berger' but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu' is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By P. G. Linder

The mechanical concentration of ores has not attained any considerable extent in Sweden, by reason of a scarcity of ores calling for this kind of treatment. Of rich iron-ores there is still an abundant supply; and magnetic concentration, which in the future undoubtedly will become of great importance, not being as yet demanded by necessity, has not advanced beyond a few experiments. At the copper-mines mechanical concentration has been superseded by chemical processes; the lead mines are worked out; and it is (with one exception) only the mines producing blende, or blende and galena intimately mixed, that have adopted mechanical methods for enriching their low-grade ores. While the concentrating-plants in Sweden are few and their output is comparatively insignificant, the methods employed, the general features of the work and the results obtained under extremely unfavorable conditions, may offer some points of interest to persons who are engaged in this branch of industry and have similar problems to deal with. Before going into a detailed description of the several plants, I will offer a few remarks that hold good for all of them and constitute a general review of Swedish concentration and its conditions. At all the works the ore to be treated is a mixture of blende and

Jan 1, 1895

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984