Search Documents

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,' or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9' per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,' or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9' per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By R. S. Dean

ALTHOUGH it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satis-factory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It. must form in low concentrations a copious but not too persist-ent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting Dower and very little emulsifying power.

Jan 1, 1935

By C. Everard Arnold

The Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mine. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising; 15 ft. of sinking was done so that the bearers, collar-set, and three shaftrsets might be installed and concreted, and with this done it mas possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 f't. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. airhoist was installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21 ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8-by 8-in. struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jan 1, 1911

By W. S. Cavender

The Round Mountain mining district, Nye County, Ne- vada, was discovered in 1906 on claims owned by Lewis D. Gordon. Initial mining operations uncovered gold veins of spectacular richness, and within a few days of discovery, Gordon sold his controlling interest for some $87,000. From this sale emerged the Round Mountain Mining Co., predecessor of Nevada Porphyry Gold Mines, Inc., the latter destined to become the major property owner in the area. Vein mining in the district continued sporadically into the early 1930s, yielding 9.3 Mg (330,000 oz) of gold plus substantial silver credits from approximately 626 kt (690,000 st) of ore. In addition to the lode deposits, the early miners recognized the placer potential in the alluvial fan material accumulated around the west and north sides of Round Mountain itself. Intermittent placer operations were carried out for a number of years, and in the 1940s and 1950s, Round Mountain Gold Dredging Co. worked the placers under a lease from Nevada Porphyry Gold Mines. The last placer operation terminated in 1959 when it, like some of its predecessors, proved uneconomic. Total placer production for the district is estimated at 3657 km (4 million yd) of gravel containing 59 Mg (210,000 oz) of gold and possibly 2.0 to 2.3 Mg (70,000 to 80,000 oz) of silver. Round Mountain is a small hill situated on the east flank of the Toquima Range in central Nevada. The hill is com- posed of relatively flat-lying Tertiary rhyolitic ash flow tuffs, which overlie Paleozoic metasediments and Cretaceous granites. Throughout the surrounding Round Mountain mining district, most of the known gold ores occur in the tuffs, although the metasediments and granites are also mineralized. Mineralization is structurally controlled, principally by a series of northwest-trending shears and shattered zones. Vein, stockwork, and disseminated ores occur, usually containing simple quartz-pyrite-gold mineral assemblages. The gold itself is electrum, having a silver content of 30% to 40%. In September, 1967, Elwood Dietrich, a prospector and mine promoter, obtained a purchase option on the 4452 ha (1 1,000 acres) of mineral rights held at Round Mountain by Nevada Porphyry Gold Mines. The original option had a buy-out price of $1 million and was established through Dietrich's friendship with officers of Nevada Porphyry. In April, 1968, Dietrich conveyed his option to Ordrich Gold Reserves Co., a partnership created by a group of west coast investors, mostly employees of the airline industry. There- after, Ordrich invested considerable funds in trying to test and develop the property, but soon recognized the need to seek financial and technical support from the mining industry. In December, 1968, Dietrich contacted Wayne Cavender, then Regional Geologist, Southwest, for Copper Range Exploration Company (CRX) in Tucson, Arizona, and made a data presentation. Shortly thereafter, Cavender was appointed Manager of Exploration and Chief Geologist for Copper Range Co. (parent company of CRX), New York City, and he asked C. Phillips Purdy, CRX Regional Geologist, Northwest, to make an initial property examination. Purdy's one-week field study took place in March, 1969, and resulted in a recommendation that CRX pursue its investigation of the property. The presence of low-grade gold mineralization in both the alluvial gravels and in the bedrock was verifiable, but the placer was deemed to have the greater immediate economic mining potential. At that time, gold was in the $1.41/g ($40 per oz) price range. Working from Purdy's information, Cavender decided to attempt acquisition of the property, and the first in a long series of negotiations was initiated with Ordrich. Basically, CRX felt that the placer had a promising potential for several reasons, including (I) past operators had recovered free gold but not the gold contained in the pebble fraction of the gravels; (2) past operations appeared to have been ineffectively designed or managed and not costefficient; and (3) the price of gold appeared to be poised for an upward move. Negotiations with Ordrich were prolonged and difficult, with CRX competing against several ma* mining companies, but finally an agreement was reached, effective June I, 1970. Gold was then back to $35. It is believed that, in

Jan 1, 1985

By Willard L. Cumings, Benjamin L. Miller

The Camaguey brown iron-ore deposit covers the top of Sari Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name " San Belipe district" is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,' who says: " The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camagueg City, in the province of Camagueg.....Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements .as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp2 has the following to say of ores in Camaguey Province:

Jan 1, 1912

By N. Brown, M. Herman

IT has been pointed out by Cottrell' and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a' in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n'a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By R. W. Raymond

At the Pittsburg meeting of the Institute, in March, 1910, the death of Mr. Metcalf was announced, and Col. H. P. Bope, of Pittsburg, delivered in memory of him a brief but eloquent address, which, though expressing the Norrow of Mr. Metcalf's friends, and, in general terms, the debt of gratitude which his country and his profession owed to him, was not intended to be a complete survey of his life and work. With Colonel Rope's permission, and with the aid of some of the statements in his address, I substitute for it, in our Transactions, this more cletailed, yet still inadequate memorial. As Colonel Rope justly remarked, the men who could do justice to this theme—such men as Jones, Chalfant, Bennett, Oliver, and Park—passed away before Metcalf, leaving him almost the last of the generation of great steel-makers who made Pittsburg the Sheffield of America, and who discharged a double function, as the rearguard of the old metallurgical practice and the ran-guard of the new. I knew many of them; would that I were better qualified to celebrate their achievements. William Metcalf was born Sept. 3, 1838, at Pittsburg, Pa., where his father, Orlando Metcalf, was an eminent member of the bar. At the age of sixteen, he entered the Rensselaer Polytechnic Institute, at Troy, N. Y., from which he was graduated in June, 1858: Returning to his native city, he became an assistant engineer in the Fort Pitt Foundry, of which he was made Superintendent in 1859. This famous establishment produced the largest castings and heaviest machinery then knolrn in the United States; and Mr. Metcalf's intense, intelligent and incessant study of his business prepared him as a manufacturer for a patriotic service to his country more valuable than, as a soldier, he could have rendered in the field. The call came in 1862, when the government needed, above all things, a supply of field, naval and siege artillery. The

Jan 1, 1911

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 30c0 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H, Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles.

Jan 1, 1940

By Walter McDermott

This machine is an improvement on the well-known endless travelling belt used for dressing slimes in many mills; the chief point of difference, and constituting the essential advantage of the present over the old form, is the application to the machine of a secondary agitating or shaking motion, in addition to the ordinary progressive motion of- the belt. In the machine as heretofore made, the inclined belt or apron moved slowly up against a thin stream of water and ore, depositing the concentrations carried over in a tank placed below, through which the belt travelled, of course, in a reversed position. By reference to the accompanying drawings, it will be seen that in this main principle the new modification does not differ materially; but the means by which it is carried out are essentially different. The machine consists of a substantial frame of mood, F, Figs. 41, 42, and 43, within which hang the shaking frame and rollers, B B, A, Endless apron ; B, Apron frame and rollers ; C, Driving drum ; D, pulleys; B, Shaft and connecting rods; F, Wooden frame; G, Shaft of regulating Pulley; H, Yokes. supporting the upper half of the travelling apron, A, which passes below around the driving drum, C, in the water-tank, J. On leaving the water-tank, the belt passes over the guiding and tightener pulley, G. The ends of the shaking-frame, B, are provided with iron yokes, H H, bored to admit the shafts of the end rollers, and carrying a lug, by which attachment is made to the connecting rods,

By Marcel R. Daly

In a preceding paper1 the writer has pointed out some apparent relationship between the distribution, on the surface of the globe,, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth's body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the prc-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limcstone); and the Beltian system of the same region contains layers of argillitcs and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons under conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. Thcy constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the different stages of evolution of the primitive, parent matter. The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunning-gam-Craig has recently shown how intimately shale fields and oil fields are connectcd.4 For this reason, no distinction is made in the present

Jan 1, 1918

By Augustus Locke

San Francisco Meeting, October, 1911.) Two Opposed Interpretations of the Tonopah Structure.-The important geological publications concerning the Tonopah mining-district are those of Spurr 1 and of Burgess.2 In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks agreeably conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Briefly, Burgess regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesite, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.-The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of 1 Geology of the Tonopah Mining District, Nevada, Professional Paper No. 42, U. S. Geological Survey (1905). Report on the Geology of the Property of the Montana-Tonopah Mining Co. (1910). An abstract of this report is given in the Mining and Scientific Press, vol. cii., No. 16,p. 560 (Apr. 22, 1911). 2 The Geology of the Producing Part of the Tonopah Mining District, Economic Geology, vol. iv., No. 8, pp. 681 to 712 (Dec., 1909).

Feb 1, 1912

By Franklin R. Carpenter, W. P. Headden

TWO notes have already appeared in the Transactions concerning the columbite or tantalite of the Black Hills tin-mines. In vol. xiii., page 232, Prof. Schaeffer speaks of the mineral as tantalite, and concludes by saying that its separation from the tinstone "is a matter which will, I believe, prove puzzling to the wisest metallurgist." He also observes that he is unable to find by analysis in his specimens the least trace of columbic acid. Prof. W. P. Blake, in the same volume, at page 696, says: " Even if it [tantalite or columbite] were present to a considerable amount, it would not injure the tin in smelting. It does not alloy with tin, but carries a small percentage of tin, which would probably be liberated in smelting." He calls the mineral columbite from the fact that a great number of specificgravity tests invariably indicated that it should be so classed. We have made chemical tests as well as specific-gravity tests upon many samples from many different parts of the Hills. Our analyses have always shown the presence of columbic acid, and the specificgravity tests have always indicated columbite, as we have elsewhere shown.* As Prof. Blake has already observed, it is not found in such close association with the tin as to prevent separation by a rough handsorting, but it is usually present with the stream-tin. As Prof. Schaeffer says, it cannot be separated by ordinary concentration; and while, as declared by Prof. Blake, its columbic acid may not unite with the tin in any form, yet its iron and manganese oxides may be reduced, and thus lower the quality of the tin produced, as is also the case when the smelting charge contains wolfram. To determine the effect of columbite in the ordinary potassium cyanide assay, there were assayed at the Dakota School of Mines four samples containing different proportions of columbite. The results, published in the report of the school for 1888, seemed to indi-

Jan 1, 1889

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By Casper A. Nelson, Wendell M. Whitecotton

A WIDE variety of lead ore is treated by the Midvale Smelter, for it is a custom plant not only treating Company lead concentrate and direct-smelting ores but also custom ores and concentrates, principally from Utah, Idaho, and Nevada, with lesser amounts from Arizona, California, Colorado, Montana, Oregon, and Washington. The principal operating departments of the plant are weighing and sampling, Wedge roaster, D&L sintering, blast furnace and drossing, and baghouse. The lead bullion produced is shipped to a subsidiary, the U.S.S. Lead Refinery, Inc., at East Chicago, while the by-products, such as matte and speiss, are shipped to other smelters or re-treated at the plant.

Jan 1, 1948

By C. S. Finney, John Mitchell

On December 31, 1959, there existed in the United States 15,993 slot-type coke ovens capable of producing 81,447,700 net tons of coke. These ovens were concentrated in 74 coke plants in 21 different states. As of the same date, there were 7448 beehive ovens in existence at 45 plants in the states of Pennsylvania, Virginia, West Virginia, and Kentucky. Total annual capacity of the existing beehive ovens was 4,368,800 net tons, but only 5148 ovens with a capacity of 3,131,600 tons were in operating condition. It is interesting to compare the average dimensions of slot-type ovens built during recent years with the 30 ft x 5 ½ ft x 16 ½ in. ovens erected at Syracuse, N. Y. in 1892. A composite oven built according to the average dimensions of all those erected between 1954 and 1958, for instance, would be 39 ft long. 12 ft high, and 18 in. in width. The coal capacity would be 16 tons as against the 4.4 tons which could be charged to the Syracuse ovens. Of the 15.993 slot- type ovens in existence at the end of 1959, by far the greater number were built by the Koppers Co. whose total of 11,280 ovens included 7891 Koppers- Becker and 3389 Koppers ovens. Of the remainder, there were 3260 Wilputte, 1350 Semet-Solvay, 63 Otto, and 40 Simon Carves ovens. By-product coke oven plants are usually classified either as furnace or merchant plants. According to the definitions used by the US Bureau of Mines, the former are "those that are owned by or financially affiliated with iron and steel companies whose main business is producing coke for use in their own blast furnaces. All other coke plants are classified as merchant. They include those that manufacture metallurgical, industrial, and residential heating grades of coke for sale on the open market; coke plants associated with chemical companies or gas utilities; and those affiliated with local iron works, where only a small part (less than 50 pct of their output) is used in affiliated blast furnaces." The annual coke capacity of the merchant plants during 1959 was 10,393,000 tons. However, the by-product oven of today is essentially an appurtenance of the iron and steel industry, rather more than 87 pct of total by- product coking capacity being concentrated at furnace plants. This was not always so. There was a time when the merchant plants played a much greater part in meeting the US demand for coke and gas. High noon for the merchant plants was reached during the early 1930's. By 1932 there were as many by- product oven installations being operated by the merchant sector of the industry as by the coke divisions of the iron and steel industry (44 of each), and in the same year the merchant plants produced 46.5 pct of all by-product coke made in the country. Since that time their contribution has drastically declined. In 1940 merchant plants were responsible for only 23.2 pct of total US production, and by 1950 their number had decreased to 30 plants which turned out 18.5 pct of the total by-product coke made. At the end of 1959 only 20 of the 74 existing by-product oven installations were merchant plants. They ac- counted for 12.5 pct of the year's production, or 6,849,786 net tons. This percentage has remained fairly constant since 1954. There are several reasons for the decline of the merchant coking industry. For example. On the grounds of economy, quality control, continuity of supply, and so on, the iron and steel industry usually prefers to control its own mines and carbonize its own coal at or near to the blast furnace rather than rely on independent operators for metallurgical coke. As the steel companies have enlarged their own coking facilities, so has the need for coke obtained from other sources declined. Furthermore, not only has the steel industry increased in self-sufficiency by building mare coke ovens during recent years, but it has also progressively improved the fuel efficiency of its blast furnaces. During the years 1947-49 the average coke consumption per ton of pig iron was 1892.8 lb. During 1958 the corresponding figure was 1613.4 lb. There are many individual furnaces where still better results are being obtained, and further reductions in the average may be expected. Perhaps the greatest threat to the merchant coking plant has been the fantastic increase in the use of natural gas and petroleum products for purposes which manufactured gas once served. So deadly has the com- petition from natural gas and oil been that it has almost eliminated by-product oven installations owned by public utilities. In the peak years of the early 1930's there were 23 such public utility plants. In 1960 only two were left. One of these, owned by the Citizens Gas and Coke Utility, was at Indianapolis, Ind.; the other was the plant operated by the Philadelphia Electric Co. at Chester, Pa. The non-utility merchant plants have also been sorely hit. With gas sales revenues reduced, domestic

Jan 1, 1961

By Zay Jeffries

THE metallic products of today represent the temporary end point of the efforts and interplay of thousands of years of the human struggle for existence, for pleasure, for conquest, for defense, for improvement in the standard of living, and for the satisfaction of that irrepressible urge to discover and utilize the materials and laws of nature Each metal has gained its place in the sun in severe competition with all other materials, be they metallic or nonmetallic Each serves better than any other for certain purposes. The compromise between cost and properties usually determines the selection of a metallic product for a given use. There are exceptions, as in wartime when the availability at a certain place at a certain time may far outweigh the ordinary economic considerations. In many instances superior properties are vastly more important than cost. If this were not so, the metal industry, for practical purposes, would be the iron industry. The use of 38,000,000 metric tons of newly produced nonferrous metal during, the five-year period from 1940 through 1944 is ample evidence that the special properties of these many metals have great economic value. In fact, our extensive industrial advances would have been quite impossible without the great range and variety of properties and combinations of properties of the nonferrous metals. This observation is not made to detract in the slightest way from the dominant role played by iron and steel. During the past century the production of pig iron has constituted well over 90 per

Jan 1, 1947