Search Documents

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By P. E. Hildebrand, S. W. Mao, C. N. Crain

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case in point. In the preparation of a regional plan for the massive program of groundwater development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more or less general interest are described herein. The first involves basic development policy, i.e., the question of whether groundwater development should be based on the demand of the economy, or the conservation concept of safe yield. The analysis demonstrated that mining of groundwater is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design. From an analysis of all pertinent factors, a simple nomograph was derived for determining well specifications on site during construction. The nomograph can be modified for use in any alluvial terrain. In the Northern Zone of the Indus Plains —the region known as the Punjab- Pakistan is proceeding with integrated development of water and land resources on a scale never before contemplated. The heart of the development plan is a massive program of groundwater development to supplement canal irrigation supplies and to provide drainage relief to the irrigated lands. By the close of 1966 about 2500 high-capacity wells were in operation and furnishing the water supply and drainage requirements for nearly two million irrigated acres. The development plan calls for the construction of a total of nearly 30,000 wells with an aggregate capacity of 120,000 cfs by 1980. This is part of an integrated program eventually affecting over 20 million acres of irrigated lands. [This development program is administered by the West Pakistan Water and Power Development Authority (WAPDA) for which the firm of Tipton and Kalm-bach, Inc. serves as regional planning consultant for the Northern Zone. The material presented herein is derived from planning studies which have been made in connection with the preparation of a regional development plan for the Northern zone.] Pakistan is proceeding with this large-scale development of land and water resources at a time when she is at the threshold of an almost calamitous population growth. Furthermore, she is attempting this development at a time when most of her usable land is already occupied and her food demands exceed current production. Here in the Northern Zone is one of the largest continuous areas of irrigated land in the world, easily irrigated, with a warm, dry climate and ample potential supplies of surface water and groundwater. Except for an abundance of land and labor, other primary resources are lacking or in very limited supply. The agriculture sector so dominates the economy that only by means of an effective development of the agricultural resources can other sectors grow and contribute to a viable economy. Because of inadequate irrigation, farming here has not effectively participated in the twentieth century revolution in agriculture, and only by means of massive development of potential supplies can Pakistan catch up. Capital for any kind of mass development must come from the outside. But the overriding restraint to development of the land and labor resources is the availability of water. ECONOMICS OF DEVELOPMENT The decision-making process in planning regional development becomes increasingly complex as the various sectors of the economy become more highly developed. Where, as in this case, one sector dominates the economy and its development can be considered the key to development of other sectors, the decision-making process is simplified and it is easier to identify alternatives and to trace the prob-

Jan 1, 1970

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.' The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By Edward E. Hicke, Charles A. Stickels

The dihedral angle of liquid-lead inclusions in solid nickel has been measured as a function of temperature from 371 to 816 C at zero pressure. and as a function of pressure up to 50,000 psi at 317 and 593 C. Thermodynamic expressions are derived for the temperature and pressure coefficients of interfacial tensions in this system. A method is presented for obtaining relative tempmature and pressure coefficients from dihedral-angle data, and the resulting values are used in conjunction with the thermodynamic relations to calculate excess properties of the solid-liquid interface. Defining the position of the solid-liquid interface by the condition that the excess concentration of lead is zero, the excess concentration of nickel and the excess entropy at the solid-liquid interface are: where y(593) is the interfacial tension of the nickel grain boundary saturated with lead at 593C and zero pressure. These values are considered reliable to within a factor of two. While similar calculations are not possible for the nickel grain boundary, it is shown that the expwimental results imply that the excess concentration of nickel at the boundary and the excess entropy of the boundary are negative. THE temperature and composition dependencies of interfacial tensions in metal systems have been reported by several authors in the last 15 years.'-' No measurements of the effect of pressure on inter- facial tensions in metals have been reported, although measurements made on nonmetallic gas/liquid and liquid/liquid systems suggest that a measurable effect should exist.6-l2 The purpose of these experiments was to determine the influence of temperature and hydrostatic pressure on dihedral angles in the Pb-Ni system. The equilibrium dihedral angle is expressed as a ratio of interfacial tensions by2: where 8 is the dihedral angle, yGB is the Ni-Ni grain boundary tension, and SL is the solid Ni-liquid Pb interfacial tension. Three sets of ex- periments were run to determine: a) the effect of temperature from 371" to 816°C on the dihedral angle at zero pressure; b) the effect of pressure up to 50,000 psi on the dihedral angle at 371° and 593°C. THERMODYNAMICS The properties of interfaces of most direct concern are the interfacial tension, excess concentrations of various components at the interface and the excess entropy of the interface, S°. These quantities are defined following Gibbs. Consider an interface separating phases a and 0. Construct two surfaces C, and C such that all properties of phase a remain uniform up to C, and all properties of phase 0 remain uniform up to C. The region between C, and Cp is the interfacial region. Let a "dividing surface", D, be constructed in the interfacial region such that it passes through all points "similarly situated with respect to the condition of the adjacent matter."l3 Surface D divides the interfacial region into a portion a' adjacent to phase adjacent to phase . Let a closed curve, C, enclose an area A in D. Erect normal lines to D along C; these lines and the surfaces C,, Cp, and D then enclose volumes V and V' in the two halves of the portion of the

Jan 1, 1964

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken&apos;s method1&apos; for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By Charles L. Mantell, George Ferment

This investigation determined the jeasibility of current-potential curves as an analytical tool for monitoving manganese electroicinning solutions for metallic impurities. Nine metallic impurities were studied: trickel, cobalt, silver, copper, zinc, molybdenum, catlmiun magnesium, and sodium. The individual effect of each metallic irzplrl,iLy on the standard point-izatiorr was determined for a range of &apos;concentration. Not all of Ihe impurities affected the polarization curve; correlation between transition current and cotrcetztration of impurity. Molybdenum had an uncorrelated effect on the polarization curie. The effects of binary mixtures of impurities were studied to see if the transition current of the mixture could be predicted. Interactions occurred between impurities which prei&apos;etzted the pvecliction the transition current of tile rrlisLitr.e by additive laws. The polarization curve was shown to be sensitive to metallic impurities which affect the current efficiency of a manganese cell. THE application of current-potential curves in manganese electrowinning is not new but played an important part in the conversion of an inoperative large-scale pilot plant into a continuous comnercial operation.1"" The effects of trace metallic impurities in manganese electrowinning solutions on cathode current-potential curves,5-19 specifically nine impurities (nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium) were studied for a range of concentrations. Cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity: molybdenum had an uncorrelated effect. Binary mixtures of impurities were studied to de-termine if the transition current could be predicted from the values for the individual constituents. Interactions between impurities prevented the prediction of the transition current of the mixtures by an additive law. The polarization curve was shown to be sensitive to metallic impurities which affected the rurrent efficiency of a manganese cell. The electrowinning of manganese relies upon maintaining a high-purity electrolyte. Purification schemes were developed to remove all of the heavy metals, the magnesium and calcium. Concentration limits have been established for single impurities. With high-purity electrolytes, favorable cell efficiencies are consistently obtained; but with impure solutions there is a reduction in efficiency. With the rapid rise to commercial prominence of electrochemical processes, there has been a lag in developing rapid methods for determining whether an electrolyte is sufficiently pure for efficient electrolysis. The most sensitive test for impurities is the behavior of the electrochemical cell. Impure electrolytes will cause a serious reduction in cell efficiency, and in many cases metal deposition will be prevented or reversed. The effects of impurities are not usually evident until after long periods of electrolysis, resulting in a disruption of the process. A method which could predict the behavior of an electrolyte in terms of cell efficiency prior to reaching the commercial cell is needed. Van Arsdale and Maier," Allmand and Campbell,a1&apos;22 and others attempted to develop an electrochemical process for manganese,"3"29 but all met with some degree of difficulty. Jacobs et a studied the effects of metallic impurities in manganese electrowinning. Plant methods were based on a 2-hr plating in a small electrolytic cell. The final method was based on a 24-hr plating run, performed in a relatively large test cell. Here, current efficiencies were calculated with and without impurities in the electrolyte, and the critical concentration was established as the maximum amount of impurity that the electrolyte could tolerate before there was a serious loss in efficiency. The amount of impurity that could be tolerated decreased as the plating time increased, indicating deposition of the impurity. This test duplicated the conditions of commercial practire, and was sensitive to impurities. Small amounts of impurities significantly affect the hydrogen overvoltage at a metal surface, increasing or decreasing it depending upon the nature of the impurity. ockris established the limit for the onset of poisoning at 10-l moles per liter. The effects of impurities were studied by potential-time curves at a constant current density. The technique did not lend itself to rapid analysis in that several hours were needed to establish stable potential-time curves. Serfass and coworkers3&apos; developed calorimetric and spectrophotometric techniques for analyzing for trace impurities. Our method4&apos;" is based on current-cathode potential curves produced by continuously changing the cell voltage at a programmed rate. Starting with a clean stainless-steel cathode, the cell voltage was initially adjusted to yield zero current: the program was then started and the current was plotted as a function of the cathode potential. Fig. 1 is a typical current-potential curve. In initial region A the hydrogen-evolution reaction predominates and the polarization curve

Jan 1, 1967

Editors of engineering periodicals usually read the advertising pages. It may be hard&apos; for some men, let alone engineers, to understand what value there is in reading "dry advertisements." Yet it is a fact that valuable suggestions have been obtained from these so-called "dry advertisements" which have been the means of securing greater efficiency in the performance of some undertaking and consequent saving of time and money. It seems to be an editorial practice to look to the advertisements for suggestions for the reading pages. It is a fact that some of the most appreciated descriptive articles were suggested by advertisements. Every undertaking is limited to that point where tools and machinery for its successful performance and completion may be purchased or manufactured. No work can he planned without having in mind such limitation, and the technical journals may be relied upon to furnish descriptions, both editorially and through the advertising pages, of methods and plant used in successfully performing various tasks. This being so, why should not the reader or subscriber to a magazine or periodical avail himself of such a fountain of knowledge? Such perusal proves of value to the up-to-date engineer or man occupying a -position. of responsibility where initiative is essential. Authorities agree that advertisements are on a par with technical articles for their educational value, and this Is as it should be. Also, most subscribers to a publication realize that a, successful advertising medium means a continuance of advertising patronage, which in turn enables the publisher to turn out a better and larger volume of reading matter.

Jan 6, 1915

By H. G. Doll

As a continuation of the earlier paper on the general subject of the SP log, a more complete analysis of certain features of the SP log in shaly sands is given. The pseudo-static SP in front of shaly sands is compared, on a theoretical basis, to the static SP in front of clean sands, as a function of the respective amount of shale and sand in the formation, and of the relative resistivities of the shale, of the uncontaminated part of the sand. and of the invaded zone of the sand. As a conclusion, the advantage of using reasonably conduc. tive mud in this case is shown. The discussion is illustrated by field examples. INTRODUCTION The discussion reported in the present paper is based on a theoretical analysis, and not on experiment. The field examples, joined to the text. are shown only as qualitative illustrations of the essential results of this analysis. Although the hypotheses made in the theoretical developments may perhaps be somewhat improved, it seems, nevertheless, that the results obtained account reasonably well for the actual phenomena, and give a fair approximation of their order of magnitude. The paper contains a mathematical analysis of a tri-dimen-sional distribution of potentials and current lines. due to spontaneous electromotive forces arising at the contact of shales and free electrolytes. as a function of the geometry and of the respective resistivities of the different media involved. It is assumed, although this hypothesis is not proven, that the emf&apos;s remain the same even if the shale occurs in very thin layers or in dispersed particles. It has already been pointed out 1,2,3 that, all other conditions being the same, the deflection of the SP log in front of a shaly sand is smaller than opposite a clean sand. When the thickness and the conductivity of a clean sand are large enough. the deflection of the SP log reaches a limiting value which is equal to the "static SP" of the clean sand. It is generally convenient to take the static SP of shale as the reference value or "base line." As a consequence, and for the sake of abbreviation, the expression. "static SP of a clean sand," is often used to designate the difference between the static SP of that sand and that of the shales, which difference is a measure of the total electromotive forces involved in the chain mud sand-shale. A similar limiting value is; also observed for the SP deflec-lion opposite a thick shaly sand, but it is smaller. just as if the total electromotive force involved were smaller in that case. This limiting value has been called the "Pseudo-Static SP" of the shaly sand. The static SP of a clean sand depends on the salinity of its connate water with respect to that of the mud, and, to a certain extent. on the differential pressure which controls the electro-filtration potentials, but it does not depend on the resistivity of the sand. On the contrary. the pseudo-static SP of a shaly sand depends not only on the salinity of its connate water and on the differential pressure, but also on the percentage of shale and on the resistivities of the shale, of the uncontaminated part of the sand, and of the zone invaded by the mud filtrate. If the three resistivities above were equal, the pseudo-static SP would be proportional to the percentage of sand in the shaly sand, and its departure from the static SP of a clean sand having the same connate water would simply be proportional to the percentage of shale. In that case, the pseudo-static SP of a shaly sand containing 10 per cent of shale would he 10 per cent less than the static SP of a clean sand. When. however. the sand is. on the average. substantially more resistive than the shale. the percentage of departure of the pseudo-static SP from the static SP of a clean sand is much larger than the percentage of shale. For that reason, the peaks of the SP log opposite shaly sands are systematically of smaller amplitude when the sands are oil-bearing than when they are water-bearing, all other conditions being the same. This feature is observed even when the sand beds are thick. and even when they do not contain a large percentage of shale. All this has already been described in all earlier publication", but mostly in a qualitative way. The present paper will analyze in more detail the action of the local SP currents which are generated inside of the shaly sands, and which are responsible for the abnormally low value of the pseudo-static SP. The quantitative computations have been extended to the general case of thin interbedded layers of sand and shale, where the resistivities of the shale and sand streaks do not have the same value: they are summarized in charts giving values of the pseudo-static SP of a shaly sand as a function of the different parameters involved. DEFINITIONS The static SP of a clean sand has been defined as the potential that would exist in the mud opposite that sand, were the SP current prevented from flowing. Such an ideal condition is represented on Fig. I-A. By analogy, the pseudo-static SP of a shaly sand can be defined as the potential that would exist in the hole, if the circuit shaly sand — surrounding shales — mud column were interrupted by the insulating plugs placed at the boundaries

Jan 1, 1950

By K. L. Temple, A. R. Colmer

ACID coal mine drainage presents a peculiarly difficult problem for two principal reasons. First is the fact that the amount of acid water discharged from active and abandoned mines constantly increases as coal fields are developed and thereby creates a steadily worsening nuisance of rapidly growing importance to the general public as well as to the coal industry. Second is the even more significant fact that there is no method yet known that will appreciably alleviate the acid water problem except at totally prohibitive cost to the coal operators. The problem is thus seen to be an urgent one. With a growing need for good quality water and a growing public demand for abatemknt of stream pollution, a large portion of the soft coal industry finds itself in the position of year by year dumping more and more acid into the streams and waterways and having no way in sight of improving the situation or even of keeping it from getting worse. While some studies have been made, it is only in the last few years that the problem has been seriously considered, chiefly by the group of workers under the direction of S. A. Braley at Mellon Institute and by the Bituminous Coal Research, Inc. fellowship at West Virginia University. Hinkle and Koehlerl reported the results of the earlier West Virginia work. This work pointed to certain biological aspects which had not been noticed previously. These may be summarized as two separate findings. One was that sulphur oxidizing bacteria were present in acid mine water and that their possible role in contributing to the acidity should be investigated. The other was

Jan 1, 1952

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By J. E. Burke

RECENT investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen, Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: [D=Ktn [11] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Walker4 finds that, in alpha brass, the rate of growth falls off more rapidly than indicated by Eq I after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker&apos;s data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: [t, Hr i &apos;_ III t„ = R \T, - ~) [2]] where t1 and t2 are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck.&apos; The results obtained by Beck, Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and Hu6 later demonstrated experimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,10 Making implicit use of this assumption, several authors14,15 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parker&apos; have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary, are on the average more surrounded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1948

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert&apos;s analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900&apos;C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967