Search Documents

By J. Philibert, A. G. Guy

Diffusion in the presence of deformation was studied by the method of vacuum dezincification of copper-rich and silver-rich solid solutions containing 7 to 30 pct Zn. The specimens were designed to permit the study of diffusion in separate portions of a given specimen characterized by strain rates ranging from essentially zero to approximately 10 sec-. No effect of deformation on diffusion was observed. BEGINNING with the work of Buffington and Cohen: interest in the question of the effect of stress or strain on diffusion has largely been concentrated on the enhancement of diffusion in specimens subjected to Continuous plastic deformation. The present research is a contribution to this limited area. However, as a preliminary to focusing attention on this special topic, it will be desirable to make a broad survey of the larger question, especially since there has been considerable foreign work in areas outside those of current interest in the United States. Since most of the topics referred to in the following section are both complex and imperfectly understood at present, it has been expedient in most instances to offer only a guide to the general nature of the work rather than a critical evaluation. PREVIOUS WORK The effect of elastic stress on diffusion has received considerable attention, especially with regard to the thermodynamic driving force for diffusion. The thermodynamic treatments have been based on the work of Gibb, Voigt, Planck, and Leontovich.' Konobeevskii and Selisski6 made a first attempt at treating the problem in 1933, and Gorskii7 a few years later gave a solution applicable to single crystals as well as to polycrystalline specimens. In 1943 Konobeevski8 published treatments that have been the basis of much Russian work up to the present. For example, Aleksandrov and Lyubov used his work in explaining the velocity of lateral growth of pearlite. Early work in the United States was that of Mooradian and Norton, which showed that lattice distortion tends to be relieved before it can significantly affect the diffusion process. Druyvesteyn and Berghoutl1 observed a slight effect of elastic strain on self-diffusion in copper, while de Kazinczy12 found that both elastic and plastic deformation increased the rate of diffusion of hydrogen in steel. On the other hand, Grimes58 observed no effect of either elastic or plastic straining on the diffusion of hydrogen in nickel. High-frequency alternating stresses have been reported by various investigator s13-l5 to increase the rate of diffusion. A special form of elastic stressing is the imposition of hydrostatic pressure, a condition that is amenable to Conventional thermodvnamic analysis. Most of the experimental results in this area are consistent in showing a slight decrease in diffusion rates at high pressures.16-l8 Although Geguzinl reported a pronounced effect of relatively small pressures, Barnes and Mazey20 failed to Corroborate this finding, while Guy and Spinelli21 advanced an explanation of the phenomenon observed by Geguzin. It has been recognized that the thermodynamic treatment of diffusion phenomena in an arbitrarily stressed body is complicated by the fact that the desired state of quasi-equilibrium of the shear stresses cannot be maintained during a general diffusion process. However, attempts have been made by Meix-ner22-24 and Fasto to treat certain restricted cases, such as relaxation. FastovZ7 has also incorporated the general stress tensor into the thermodynamics of irreversible processes. The lattice strain that accompanies the formation of a solid solution has been the subject of much study,28-s0 and indirectly it has entered into many recent theories of diffusion. However, some Russian investigators31'32 have taken other views of this matter and have predicted large effects on diffusion rates because of concentration stresses.o In completing this brief resume of previous work involving elastic strains and before proceeding to a consideration of the effect of continuous plastic deformation, it should be pointed out that deformation of various additional types may also influence diffusion. The effect of cold-working on subsequent diffusion has been studied directly by AndreevaS and by Schumann and Erdmann-Jesnitzer, while indirect evidence has been obtained by Miller and Guarnieri and by Vitman.38 Thermal stresses may also influence diffusion, contributions to this subject having been made by Fastovs7 and by Aleksandrov and Lyubv. The work of Johnson and Martin,o Dienes and Damask,3Band DamaskS considered the question of radiation-enhanced diffusion. In considering previous work on the subject of plastic deformation and diffusion, attention will be directed to those studies concerned primarily with diffusion rather than with its relation to Creep, e.g., the work of Dorn, or to the acceleration of diffusion -controlled reactions. Observations of the effect of

Jan 1, 1962

By E. G. Banks

THIS paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine-more especially that produced in the upper levels-contains a large proportion of hard, chalcedonic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to ob¬tain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded

Jan 1, 1907

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By C. Gatlin, N. E. Garner

Results of impulsive wedge penetration tests on two synthetic, plastically deforming rocks are presented. Basic data obtained were force-time, displacement-time, and force-displacement curves for the impacts, plus the crater geometry. Wedge geometry and blow frequency were varied over a considerable range. The synthetic rocks consisted of wax-sand mixtures; two waxes of diflerent ductilities were used to provide variable "rock" characteristics. Conventional triaxial tests showed that these synthetic rocks exhibited force-deformation curves and Mohr envelopes quite similar to real rocks, except that strengths were much lower. Measured forces from static penetration tests agreed closely with theoretical values; however, dynamic force values were much higher than the static. These latter disparities are attributed to the viscous nature of the waxes. Thus the utility of these or similar rock models must depend on the scaling of rock viscosity, which is as yet unknown for impulsive loadings at elevated stress states. It appears, however, that some macroscopic, static phenomena may be studied with wax-sand rock models. INTRODUCTION The resistance of solid materials to indentation or perforation by projectiles or other penetrators has been studied by workers in many areas. Despite these efforts no universally accepted laws or formulas are available for describing experimental observations. In the metals field the force-deformation behavior of impacting bodies is often analyzed by the Hertz law for elastic collisions, the Meyer law if plastic deformations occur, or some combination of both.' The similarities of these expressions to empirical drilling formulas of the oil industry are apparent. Beginning with the basic contributions of Simon and co-workers at Battelle,' a number of experimental papers concerning the reaction of rocks to vertical impact have appeared in the U. S. mining and petroleum literature.'-' Most published data have, to date, been obtained at atmospheric pressure, although some early high pressure information was reported by Payne and Chippendale.8 Maurer" has recently utilized available brittle impact data to develop a drilling rate equation based on the experimentally observed proportionality between crater volume and blow energy. His result agreed with earlier efforts by both Somerton, who used dimensional analysis, and Outmans, who used plasticity theory. It has long been known that rocks exhibit different modes of failure depending on the state of stress. The literature in this area is considerable; however, papers by Bredthauer, Handin and Hager,13 nd Robinson", are adequate to illustrate the point. Since rocks flow plastically at certain triaxial stress conditions, the mathematical theory of plasticity has been used to analyze the rock drilling problem. Cheatham'" has altered the wedge identation solution of Randtl to rocks, and has developed useful equations for penetrator forces under a variety of conditions. Outmans" has utilized Hill's solution in a similar manner to develop a drilling rate equation. Both Cheatham and Outmans used the linear Mohr-Coulomb rule to relate rock strength and confining pressure. The actual stress at the hole bottom is not easily ascertained, although photoelastic studies by Galle and Wil-hoit," plus the analytical treatment of Cheatham and wilhoiti8 provide some insight. Consequently it is not clear to what extent the highly idealized rheological model of a perfectly plastic solid can be realistically applied to the rock drilling problem. This paper is the first report on a long range experimental study of crater formation in rocks at elevated stress states. The data presented here are from the first phase of the project. Data obtained from impulsive wedge impacts on two synthetic, plastically deforming rocks are presented. MODEL ROCKS Geologists have long been faced with modelling the behavior of the earth and, as a consequence, have studied scaling problems in some detail.' In general, their main problem is handling the wide disparity between laboratory and geologic time. In our studies the time effects (blow velocity or rate of loading, blow duration, etc.) were essentiafly the same for both. model and prototype, as were were geometry and tooth penetration. Thus application of available scaling laws suggests that Similarity is obtained if the stress-strain curves of model and prototype are similar." For this reason Hubbert and Willis''

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By W. O. Philbrook

An engineering analysis indicates that the coke rate in present blast-furnace practice is set not by chemical or thermal needs but to give adequate charge permeability for economical driving rates. An equation showing interrelations among pressure drop, gas flow, and charge characteristics has been derived. Flooding conditions and the location of the fusion zone are discussed. Maximum ore size is probably limited by chemical re-ducibility rather than by heat transfer. THE intention of this paper is to show that the ].imitations on the production rate and coke requirement of the iron blast furnace are not primarily chemical or thermal in nature but are related to characteristics of the burden and operation that govern gas flow, heat transfer, and stock movement. A semiquantitative analysis will be developed in terms of standard engineering principles to give a useful picture of the relative importance of physical and mechanical factors in contrast with the chemical features of the process that are more commonly emphasized. Most of the details of calculation have been omitted in the interest of brevity and to avoid submerging the rnain points in a sea of arithmetic. Numerical values have been arrived at by objective methods from reported operating data or by reasonable estimates of material properties where exact data are lacking and then tested to see how well they fit practice, rather than by working backward to find what assumptions are needed to give the desired answers. The analysis is oversimplified in many ways because exact engineering relations have not yet been studied for bed distributions as complex as are known to exist in the blast-furnace stock column. One objective of this paper is to show that the blast furnace, in spite of its complexity, can be at- tacked by engineering methods in the hope that this viewpoint will stimulate the kind of research needed for a more exact treatment. The basic ideas and many of the conclusions presented are qualitatively well known. A careful literature survey to credit the source of all observations not original to the author would indeed be voluminous, and such has not been attempted. T. L. Joseph&apos;s Howe Memorial Lecture&apos; gives an excellent background of what is known about the internal workings of a blast furnace. Other important reference works or sources of specific information will be noted. It is hoped that the present paper will contribute something new, in method of attack and interpretation, that will aid in a clearer understanding of how to operate the blast furnace to best advantage. Factors Limiting Production and Coke Rates The rate of combustion of coke in a blast furnace, as in any fuel bed, is exactly proportional to the rate at which air is supplied. It is axiomatic, then, that the production rate of a furnace is limited by the rate at which it will take wind, i.e., burn coke, and the amount of coke that must be burned at the tuyeres to make a ton of iron of suitable composition. These two possible limiting factors will be considered briefly in the order mentioned. One common restriction on wind rate is flue-dust production. Since the volume of top gas is nearly proportional to the blast volume (by a factor of about 1.35 on a dry basis), an increased wind rate causes a correspondingly increased linear velocity of top gas in the throat of the furnace. The higher

Jan 1, 1955

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917

By Laurence C. Hicks

Consideration of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grube and Fleischbeinl packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmosphere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a laler paper Grube extends his work to other systems which show the same characteristics.~ He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kel1ey" points out that Grube has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1934

Joseph K. Stone, Jr. (Kaiser Engineers, Oakland, Calif.)—I would like to compliment the authors on their clear presentation of the results of their study of the pneumatic processes. We hope that the Inland Management decision to make this information available to all will induce others to release additional valuable fundamental data which they have accumulated in the field. There are two points upon which we would like to comment. In the discussion of Table VII it was indicated that the "oxygen consumptions were about the same as has been reported for other oxygen steelmaking processes". This conclusion is apparently based upon the consumption of 2100 cu ft per ton shown in Table VII. The data in Table IV also permits calculation of 2520, 2280, 2250 and 2700 cu ft per ton in heats 1 to 4, respectively. These figures are in the same general range as those reported for the Kal-Do and Rotor Processes using Thomas iron, but considerably above the following figures for four of the operating L-D Process Plants while using iron which is similar to American basic iron: Donawitz 1760 cu ft per ton Adapted from Cuscoleca&apos; LinZ 1900 cu ft per ton Trenkler & Hauttmann2 Dofasco 1850 cu ft per ton D. O. Davis:3 In addition to the differences between the consumption of gaseous oxygen in the Inland operation and in the L-D Process, there is another closely related difference. The L-D plants for which data are cited are using approximately 1 pct ore while the authors&apos; process used about 7 pct of sinter. Assuming 65 pct Fe in the sinter, the difference amounts to 400 to 500 cu ft

Jan 1, 1959

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By J. J. Gilvarry

Recently, Gilvarry1,2 has given a rigorous derivation of the proper distribution function for fragment size in single fracture, based on a closely defined physical model and deduced strictly by the laws of probability. The physical point of departure is Griffith&apos;s theory of brittle strength, identifying sub-microscopic flaws as the cause of the low strength of a solid in comparison with values implied by cohesive energies. Gilvarry and Bergstrom,4-7 and Gilvarry8 have compared the predictions of the theory with experiment, and have found excellent agreement, in general. The purpose of this communication is to sketch the extension of the theory to the case of comminution, and to indicate the applications to some examples in nature. The present treatment represents an amplification of a brief discussion appearing elsewhere. 9 Although the basic ideas of the Griffith theory are perfectly general for rupture of brittle solids, it was originally formulated with very brittle materials such as glass in mind. Moreover, Griffith&apos;s original experimental work was carried out on glass specimens. Recently, however, the theory has been extended by race" to apply directly to rocks. This extension makes the theory immediately applicable to the materials generally of interest from the standpoint of comminution. GENERAL CASE To obtain the distribution function for fragment size in single fracture, three assumptions are made, that: 1) Fracture proceeds by activation of preex-istent Griffith flaws in the volume, faces, and edges of a fragment; 2) the distributions of flaws of these three types are independent of each other; and 3) activated flaws of a particular type are distributed at random, individually and collectively, in the sense of Fry.11 The last assumption implies that each distribution is separately of Poisson type.

Jan 1, 1964

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By B. E. Grant

There are several exceptions from the practical operating viewpoint that might be taken with the paper. The author recommends using a "curve" in plotting safety factors of ropes and suggests that the U. S. Bureau of Mines change its present "step curve" method to the "curve" method. From an engineering theoretical point of view that is possible, but from a practical standpoint it is not possible. Rope manufacturers fabricate their ropes in diameter gradients of 1/16 in. to 1/4 in. which automatically sets up a step pattern gradient. If ropes were manufactured in the diameter gradients of 1/1000 of an inch or thereabouts, the curve method could be used. Also, from a practical standpoint, if an operator is to hoist from a depth of 4000 ft, for example, he will determine the size of the rope necessary for that depth, and it is only natural that he will have safety factor to spare at lesser depths, and in plotting this excess capacity the natural end result is a curve. The U. S. Bureau of Mines tables are set up so that the operator will know what size rope at the required safety factor he will need at his maximum depth. He is not concerned with lesser depths. W. A. Boyer (author&apos;s reply)-Mr. Grant states, "Rope manufacturers fabricate their ropes in diameter gradients of 1/16" to 1/4" which automatically sets up a step pattern gradient." There is no connection or relationship between the "size" pattern gradient and the present "factor of safety" step pattern gradient. The inherent factor of safety values for any particular size of rope with a given connected load when plotted for various depths is a curve, and with modern rope material and construction the inherent factor of safety curve is quite far removed from the present recommended factor of safety step curve. This is shown quite clearly in Figs. 3 and 4 of my paper.

Jan 11, 1954

By T. V. Moore

IN many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical&apos; pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas¬lift has been published-by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken; slippage must be determined empirically. This paper presents the results of some work carried on to, measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used-for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is mote efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves are of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966