Search Documents

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By H. G. Landua, Leah L. Naugle, H. H. Lowry

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Leah L. Naugle, H. H. Lowry, H. G. Landua

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Harold Cook

THE purpose of this paper is to state briefly the inspection requirements of the Bureau of Ordnance, the specifications governing the inspection, and the physical and chemical properties of the steel used in the construction of ordnance for our Navy. It would be of interest to evoke discussion on points in these specifications which do not tend to insure the production of the very best material for the purpose intended. In other words, what requirements of our specifications are useless and also in what manner are our specifications deficient? It might be well at the, start to answer the first criticism of this paper which will probably be made, and that is that the title does not agree with the subject matter. Considering metallographic work as covering only the macroscopic and microscopic examination of metals, this paper will have gone beyond the subject; but it is believed that a broader definition of metallography is that it is the study of the relation of the internal structure of metals and alloys to their composition and to their physical and- other properties. The internal structure of steel is dependent on its physical and its chemical properties. These physical properties are dependent on the chemical composition and the mechanical and thermal treatment of the steel. So it seems that this subtitle would not be entirely necessary and that the title "Metallography of Steel for Ordnance Purposes" would cover a study, not only of what we can learn of macroscopic and microscopic examination, but broadly of the whole subject of the specifications, the fulfillment of the requirements of which produce the structural conditions revealed by macroscopic and microscopic examination. .

Jan 2, 1916

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By Irwin Roman, Thomas C. Serman

It has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maximum electromotive force will be developed when the axis of rotation is perpendicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the intensities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By Hans Lundberg, Theodor Zuschlag

Based upon an instrumental improvement, a new development has taken place in the art of electrical prospecting, and some remarkable results have already been obtained with regard to potential exploration. In order to visualize the importance of this development, it is deemed advisable to review briefly the fundamental facts about potential surveys. Potential exploration may be carried out qualitatively or quantitatively. Qualitative investigations are made by determining and plotting on a map points of equal potential, whereby any anomalies are revealed, without, however, much clue to their magnitude. Quantitative investigations determine the variations of potential or potential drop, and thus show not only the location of the anomalies, but also their magnitude. Figs. 1 to 6 illustrate the influence of simple types of ground inhomo-geneities, assuming one effective exciter potential only. Such a condition can be closely realized by connecting an electric current source to two electrodes, one of which is located at a great distance. Assuming uniform ground resistivity, the resultant potential distribution mar be represented by concentric spheres. Any change from the normal condition causes a characteristic distortion of the spheres, which becomes different for different types of resistivity variation. The series of Figs. la to 6a illustrates schematically results of qualitative investigations and series lb to 6b results of quantitative investigations. Figs. 1 and 2 picture the well-known case of local resistivity variations normally encountered in ore prospecting. Figs. 3 and 4 show the reactions caused by more or less vertical resistivity contacts and Figs. 5 and 6 refer to the problem of ground-water and bedrock investigations where the resistivity contact is horizontal or nearly SO. It is evident from Figs. 5a and 6a that qualitative measurements do not permit an identification of such general geological features as widespread horizontal strata, because the resultant contraction or expansion of the equipotential circles at the surface cannot be recognized without quantitative determinations. On the other hand, qualitative measurements are well suited for the exploration of local or lateral resistivity

Jan 1, 1932

By M. R. Geer, H. F. Yancey

THE performance of coal-washing equipment, that is, the effectiveness with which coal and impurity are separated, is a subject of undisputed interest to all concerned with the preparation of coal. Through the years much has been written in both American and European literature on the performance of coal-washing equipment and its interpretation, but until recently no effort has been made to consolidate this wealth of information into a single, comprehensive treatment of the subject. A splendid effort in this direction was made at the First International Conference on Coal Preparation held in Paris in June 1950 in which representatives from virtually every coal-producing country participated. Although the scope of the conference covered the entire field of coal preparation, many of the sixty-odd papers and a great deal of the discussion dealt with the subject of evaluating washery performance. Prominence was given this subject by the Centre d'Etudes et Re-cherches, des Charbonnages de France, which sponsored the conference. This research organization, generally referred to as Cerchar, was formed in 1948 following the nationalization of the French coal industry. Since that date it has conducted an intensive study of coal preparation. Perhaps because of a fresh viewpoint, Cerchar realized immediately that complete information on the performance of French washeries and a thorough understanding of the mechanism of gravity separation were the fundamental prerequisites in a program to improve preparation practice. For this reason Cerchar concentrated on obtaining performance data and on a comprehensive study of methods of evaluating such information. Some idea of the magnitude of this work will be appreciated from the fact that 175 performance tests were made in 44 plants. The work performed by Cerchar emphasized a condition that is recognized by many of those concerned with coal preparation, namely that the lack of uniformity in presenting data on washery performance, the diversity of methods used in evaluating such information, and the frequent confusion of the terms related to performance have been prime factors militating against the progress from art to science. Thus, Cerchar feels that standardization of the methods employed for evaluating washery performance, not only in France but in the entire world, is essential to progress, and the prime objective of the Paris conference was to seek international standardization of the evaluation methods advocated by Cerchar. At the conclusion of the conference the question of standardization was referred to the International Standards Organization. A careful study of the dozen papers on the subject of evaluating washery performance presented at the conference reveals that none of the methods is new; most of them date back over a decade. Nevertheless, the intensive scrutiny of these methods brought about by the conference unquestionably has resulted in a valuable exchange of ideas and a clarification of thought that could scarcely be achieved in any other way. The object of the present report is to make available to the American coal industry the ideas developed at the conference which seem most important from an American viewpoint and to provide a critical analysis of some of the evaluation methods advocated by Cerchar. The various methods of evaluating washery performance are illustrated partly with data that have been published in American literature, and some new data have been obtained as the result of experimental work undertaken since the conference to provide information on certain controversial points. An English translation of the proceedings of the conference, including the discussion as well as the papers, will be available,' and previous to the conference Coal Age2 published a very brief description of some of the principal evaluation methods used by Cerchar. Americans will appreciate as well as do the French the desirability of standardizing both the termi-

Jan 1, 1952

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because, not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By John Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require addi-tional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894° to 898° C. The dissociation of dolomite and magnesite, although studied by several investigators, 4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By Charles Jones

(San Francisco Meeting, September, 1915) IN any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific. Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in. the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly riot due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul.

Jan 9, 1915

By Guy Ruggles

IN this paper the authors aim to chronicle the experience and salient points brought out in changing flotation reagents at a concentrator which had probably been using a minimum amount of oil at a minimum cost per ton, to a more complicated system requiring a partial chemical control. The original oils were coal tar and pine oil. The new reagents are line, xanthate and pine oil. It was found that there were no insur-mountable difficulties and eventually the cost of the new reagents per ton of ore proved to be very little more than that of the old. LIME PLANT When the question of handling lime came up there were two propositions open: (1) to handle the lime dry; (2) to handle it wet in the form of an emulsion. Granting that a dry lime feeder would function properly, delivering lime uniformly, the chief objection was the dust that would be raised when these feeders were being charged or operated, as the only possible location was on a gallery beneath which men were working. With this objection the handling of lime as an emulsion seemed to he the better scheme. The lime plant which was first installed was for experimental work on one section. This was gradually changed and developed until it was of sufficient size to accommodate 20 sections. The various changes will not be discussed and the following description deals only with the fully developed plant. Crude as it is, and perhaps somewhat expensive to operate, the lime-handling plant has been quite successful. Much has been learned which will pave the way for a better installation in the future.

Jan 1, 1927

By L. W. Kempf

ALUMINUM alloys, in common with most other metallic alloys, exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with tem-perature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative con-sideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators1-5 have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys

Jan 1, 1936

By R. W. Raymond

THE death of Privy Councilor Bruno Kerl, on March 25, 1905, terminated a distinguished and useful career. Bruno Kerl was born March 24, 1824, at St. Andreasberg in the Harz, and entered in 1840 the mining school of Clausthal, where he studied for three years, working at the same time in the mines and stamp-mills. After an additional year of practice in the silver-reduction and iron-works of the Upper Harz, he passed his examination as a metallurgical graduate, and studied for a year at Göttingen under WV filer in chemistry, Hausmann in mineralogy, and eminent teachers in other branches. In 1846 he was employed at the Oker works, but very soon left this post, to become a tutor in chemistry, metallurgy, etc., at Clausthal, where he continued to labor until 1867. During this period the Clausthal school became a completely equipped Mining Academy, and Kerl was made in 1862 a full professor. Meanwhile, in addition to the work of instruction, he discharged, simultaneously or successively, the duties of many responsible official positions in the Royal Hanoverian administration of mines and smelting-works, and also published many valuable books and treatises. Among these were professional guide-books to the Upper and Lower Harz, and their characteristic metallurgical processes; a manual of qualitative and quantitative blow-pipe analysis; another of metallurgical assaying ; and, most important of all, a Handbook of Metallurgy in four volumes, the second edition of which was issued in Leipzig, 1861-1865. This book was speedily recognized as the leading authority in its field. In this country, the English translation and revision, by Crookes and Röhrig, published about 1869, had a large circulation. In addition to these literary labors, Prof. Kerl became in

Jul 1, 1905

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By M. Cohen, S. A. Kulin

AT a recent symposium on thermodynamics in physical metallurgy1 two opposing theories of the austenite-martensite transformation were presented. Both theories agreed that this type of reaction involves a nucleation process which requires activation and that the activated nuclei develop into the well-known martensite plates with tremendous speed. However, there were essential differences in the two points of view concerning the nature of the nucleus and the mechanism by which the nucleus propagates. According to Cohen, Machlin, and Paranjpe,' the nucleus is a strain center with sufficient elastic energy to initiate a cooperative displacement among the atoms of the parent phase when a sufficiently low temperature is reached. This displacement propagates as a wave in shear-like fashion to transform the austenite into martensite without benefit of diffusion. On the other hand, Fisher, Hollomon, and Turnbull3 regard the nucleus as a solute-poor region (in the austenite) of a size which becomes supercritical relative to coherent growth into martensite when an appropriately low temperature is reached. This growth process is taken to be an atom-by- atom transfer from the receding austenite lattice to the advancing martensite lattice through the coherent interface that exists between the two phases. The present paper is not conceded with the divergent views as to the nature of the nucleus but describes some critical experiments which differentiate between the two proposed mechanisms of propagation. Fisher' has summarized the latter issue in the following way: According to the cooperative displacement theory, the speed of formation of mar-tensite plates should not be decreased by lowering the temperature, and martensite should form with extreme rapidity at very low temperatures; whereas with the alternate growth process, the speed of the martensite transformation should be retarded at very low temperatures, decreasing to zero at the absolute zero. The atom-by-atom growth mechanism predicts a marked slowing down of the reaction rate with decreasing temperature because the rate of self-diffusion in the austenite is involved in this picture. For example, Fisher, Hollomon and Turn-bull5 estimate that the activation energy for this growth process in steel is (0.34)2(0.36)* times the activation energy for self-diffusion in y-iron. The two most recent determinations of the latter quantity are 67,900" and 74,2007 cal/mol, which may be averaged as 71,000 cal/mol. This, in turn, gives a value of 3000 cal/mol for the activation energy of the atom-by-atom process, and hence the rate of growth should vary as e 8,000/RT where R is the gas constant

Jan 1, 1951

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,' current efficiency,' transference number,8 viscosity,9 surface tension,'' and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

By Euzebio P. de Oliveira

One of a recent batch of samplcs from the Serra da Baliza, in the state of Paraná, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto Uniáo to Uruguay discovered asphalt coming from eruptives that outcrop along the Rio de Peixe. The occurrence of asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botucatd sandstone is always a hard vitrified rock, from the metamorphic action of the overflowing eruptive contacts. In this region, howeyer, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used in mortar for building in Guara-puava and Palmas. South and west from Porto Uniáo, this bench of sandstone is about 50 m. thick, and is capped by a heavy bed of basic eruptives, many of which are amygdaloids. Nature of Rocks Dr. Geo. P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking." Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination of many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety of structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 1, 1921