Search Documents

By H. I. Althulee

The mines operated by the Compañía de Real del Monte y Pachuca, Pachuca, Mexico, are in two districts, the Pachuca, and Real del Monte. The principal area of mineralization is within a rectangle roughly 10 miles from east to west and 6 miles from north to south. It contains a number of veins from 2 to 20 ft. wide, which are exploited by this mining company. The scattered position of the producing mines led to the construction of two mills between 1906 and 1908; the Loreto mill, in Pachuca, averaged 2600 tons daily, and the Guerrero mill, in Real del Monte, milled 1270 tons daily. On Feb. 1, 1929, the management decided to enlarge the Loreto mill to take the combined tonnage of both mills at that time. This economic measure required the centralization of ore delivery, which would also afford a material saving in the cost of ore transport. The centralization would give the company the following advantages over the former system of operation: 1. Beneficiation at a single mill, closer to source of materials and supplies than the abandoned Guerrero mill. The refinery is also in the Loreto patio. 2. Ore delivery to surface at one point (San Juan Pachuca shaft) instead of at four. 3. Elimination of aerial tramways. To show what would be required to effect this centralization, it is necessary to describe the means by which the ore was delivered to the two mills, prior to centralization. The heart of the Real del Monte district is roughly four miles from that of the Pachuca section. The producing mines in these two districts were: Pachuca district: Real del Monte district: Santa Ana mine La Rica group Camelia group Purisima group Santa Margarita mine

Jan 1, 1934

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pig-ments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 A as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut. In light of the above, a project was initiated for the formation of single crystals of rutile. Method of Formation of Rutile Single Crystals Fortunately, purification of TiO2 produced from both titanium tetra-chloride and titanyl sulphate solutions had reached the stage where spectro-graphically pure starting material could be made. Spectrographic analysis of the feed material used in the initial experiments is compared with the present feed material in Table 1. It is apparent that the present large scale purification is approximately as good as the original experimental, small scale purification. Verneuil1 produced synthetic ruby and corundum in 1904 by the well-known flame fusion process, which today bears his name. Except for mechanical improvements the present commercial production of synthetics by flame fusion is essentially unchanged from his initial method. His burner consisted of an inner orifice through which was fed the feed material and oxygen. Surrounding this was a larger outer orifice through which was fed hydrogen at lower pressure. This arrangement consists then of a lance of oxygen burning in an atmosphere of hydrogen. The proportions of hydrogen to oxygen usually used in corundum production is about 3:1, providing there is sufficient temperature to reach the 2050.°C required for the fusion of alumina. From work done in the Titanium Division Laboratories2 and from the published work of Erlich3 it was known that rutile appears to lose oxygen near its melting point and that it would not be possible to grow single crystals in a strongly reducing environment. Consequently, in order to determine whether single crystals could be grown at all, an Airco oxygen-acetylene torch with

Jan 1, 1950

By B. F. Fackenthal

One of the practical questions presented to the blast-furnace manager, with regard to which little help can be obtained from existing technical literature, is the manner of filling and blowing-in. This operation is often performed according, more or less, to traditions which have come down from earlier practice, and which, if not positively detrimental when followed with the large modern furnace, may at least be greatly improved, just as the running of the furnace itself, while in blast, has been improved. It is not necessary, as many of the old furnace-men believed, to make a lot of white or silver-gray iron at the start, or to spend many weeks, or months even, in bringing the furnace to its normal burden. It has seemed to me that the publication of carefully-recorded data of practice on this point may be interesting to the members of the Institute engaged in the management of blast-furnaces. The enlarged blast-furnace at the Durham Iron Works, Riegelsville, Pa., owned by Messrs. Cooper & Hewitt, of New York City, was first put in blast February 21, 1876, since which time it has made seven blasts, and is now running on the eighth. A description of the furnace-plant, together with a record of the fifth blast, was given in my paper read at the Chattanooga meeting, May, 1885 (Transactions, xiv., 130). After some of the early blasts the furnace-lines underwent considerable change, and I have thought best to accompany this paper with drawings showing the lines and the tuyere-arrangement (see Plates I. and II.), and to give also the following summary of the conditions and results of each blast. During the first and second blasts no coke was used, and the furnace ran very irregularly, showing a constant tendency to scaffold, which was attributed, in great part, to the small hearth and other defective lines. The large proportion of air required at this furnace is accounted for by the fact that the engines are defective, and do not deliver into the furnace the amount of air indicated by the pistondisplacement.

Jan 1, 1890

By Sherwin F. Kelly

LITERALLY from the four corners of the earth, from Jerusalem and China, from Mysore and Uganda, as well as from geophysicists in the United States, came contributions from workers in magnetic and electrical geo-physical methods, most of them unfortunately unable to be present themselves. The most lively discussion centered on the phenomena of natural potentials in the earth, dealt with in M. B. R. Rao's paper from Mysore, and in Parke Dickey's contribution, which he presented in person. In the oil fields, the weak potentials observed in sedimentary strata traversed by bore holes have traditionally been ascribed to phenomena of electro-filtration and electro-capillarity. Research tending to refute this theory was presented by Dickey, who reported the existence of natural potentials in core samples, and between strata exposed in underground workings. This precipitated a lively discussion as to the possible role of electro-filtration, selective adsorption of ions by mineral particles, and electrolytic potentials, in the production of this phenomenon.

Jan 1, 1943

By L. L. Wyman

IN order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess hinder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350° C.

Jan 1, 1930

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu'm at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant' tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-' mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal, Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals: Coal, although it is one of the most important minerals, was omitted because not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By M. O. Holowaty, C. M. Squarcy

Blast furnaces are the tools of men, and it is men who have made them great. Here is presented the story of the Ironmakers-the men who first poured hot metal into what would someday be the sinews of a nation. W HEN the Jacobean merchant adventurers bade farewell to the first ship of colonists sailing for the new land, they instructed them to direct all their skill and energy to grow silk worms in Virginia. The adventurers felt sure that they could flood the market with highly priced and much desired goods like silk, sugar, tea, and indigo. They were also convinced that they would fill the needs of the mother country for iron. Early iron production in the colonies The merchants certainly had a wonderful imagination, for silk and indigo were just as exotic in Virginia as they were in England. The settlers found it more profitable to raise tobacco on the vast stretches of the free, fertile land. Thus the plans of settlers clashed with those of The Virginia Co.; and only point of agreement was the desire to produce iron. But, even there the motives of the settlers and those of The Virginia Co. of London were worlds apart. The settlers wanted to produce the tools badly needed in the colony, while the Company desired to cash in on the rising demand for iron which the home industry could not satisfy. Both the settlers and the Company lost no time trying to find iron ore. Locations of the early mines are not known. If, however, the reports of the Irishman, Francis Maguel, can be trusted, as early as 1609 a ship sailed for England with a load of 17 tons of crude iron which the East India Co. purchased at £ 4 per ton. The iron was of excellent quality and considered the best iron made of non-English ore that was ever purchased.

Jan 1, 1961

By Albert Hill Fay

In giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N 65° 35' and long. W. 168o. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the Westernmost point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions arc of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption " The Land's End of Two Worlds." "The Arctic Ocean encircles with a belt of eternal ice, the desert confines of Siberia and North America—the uttermost limits of the Old and New World, separated by the narrow channel known as Bering's Straits. " To the north, this desert is bounded by a ragged const, bristling with huge black rocks. At the base of this Titanic mass lies enchained the petrified ocean (Bering sea) whose spell-bound waves appear fixed as vast ranges of ice mountains, their blue peaks fading away in the far-off frost-smoke, or snow-vapor. " Between the twin peak* of East Cape, the termination of Siberia, the sullen sea is Been to drive tall icebergs across a stream of dead green. There lies Bering's Strait. Opposite, and towering over the channel, rise the granite masses of Cape Prince of Wales, the headland of North America. "These lonely latitudes do not belong to the habitable world."

Jan 1, 1908

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946

By Bruce W. Gonser, Robert I. Jaffee

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By Robert I. Jaffee, Bruce W. Gonser

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Hallet R. Robbins

Korea, the ancient" Hermit Kingdom," is a peninsula jutting out from the coast of eastern Asia. By the natives it is called " Chosen," nfhich, translated, means " Land of the Morning Calm." It lies between the Yellow sea and the Sea of Japan. On the north it is separated from Manchuria and the Russian province of Primorsk by the Yalu and Tiumen rivers; on the south the Korcan straits interpose a rough voyage of 120 nliles to the nearest point in Japan. The entire country is situated between the parallels of 34O and 42O N. latitude. The surface of the country is made up of successive ranges of ul~glaciated mountains, separated by narrow, fertile, and more or less densely populated, valleys. Through all the obscure centuries of its history, Korea has succeeded in maintaining a monastic seclusion, over which, from time immeniorial until the late Chino-Japanese war in 1894, China exercised a shadowy sovereignty. Although Korea had been forced into slight foreign contact previously, her first forcign treaty was signed with Japan in 1876. Under the restraining guardianship of China, the Japanese treaty bore but infiignificant innovations for Korea; but when, in 1883, a treaty was made with the United States, the first of the western nations, a decade after the American gunboats, under Commodore Rodgers and Lieutenant Schley, forced their may up the Salee river, Korea awoke from her sleep of 4,000 years. The Eorean peninsula suddenly became the arena where the enterprises and individuals of many foreign nations met in fiercest rivalry. Out of this struggle grew two singularly successful American enterprises, both of which have played an important part in developing the natural resources of the country. The first, and best known of these, is the Oriental Consolidated Mining Co., which was organized by Lcigh Hunt

Jan 1, 1909

By Wheeler P. Davey

In an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. l.) Fig. 2 is a photograph of the end of the punching, showing the hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of radiographing metals. In order to gain some preliminary data, several pieces of 1/2-in. (12.5-mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter I.........................................1/4 in. =6.3 mm 2........................................1/8 in. =3.l mm. 3................................... 1/16 in. = 1.6mm. 4....................................... 1/32 in. = 0.8 mm. 5........................................1/64 in. = 0.4 mm. Exposures were made on Seed X-ray plates at 20 in. (50 cm.) distance with Coolidge tube X-117, operated on Scheidel-Western induction coil with mercury turbine break. The X-ray plate was placed on a sheet of 1/8in. (3.1-mm.) lead. The steel was placed above this and a Iead

Jan 1, 1916

By N. H. Mannakee

[Secretary's Note.—At the Spokane meeting of the Institute, in discussion of President Brunton's address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton's address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By H. Landsberg

IN a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know.? THE CONVERGENCE RECORDER For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy over-burden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This was partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/-mm. divisions was fixed and a knife-edge, which was attached to the upper tube, was slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. 1). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By Ancel St. John

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. SCOPE OF THE INVESTIGATION The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of thoria detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

Jan 1, 1928

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970