Search Documents

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By A. William Johnson

It was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that .will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomo-geneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot be obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yield information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most importarlt types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in 3 gold-lead

Jan 1, 1942

By A. William Johnson

It was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that .will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomo-geneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot be obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yield information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most importarlt types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in 3 gold-lead

Jan 1, 1942

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with' foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939

By Konrad Stern

The terms asphalt and bitumen have been applied interchangeably, although incorrectly on occasion, for centuries to various bituminous materials that were found in nature. Native bituminous materials of only the solid types, deposits of which are found on or near the surface of the ground, together with the principal asphaltic type petroleum bitumens will be considered in this chapter. The international dictionary compiled by the "Permanent International Association of Road Congresses" still gives the full name as "Asphaltic Bitumen" but of recent years the word "Bitumen" has been recognized as most appropriate and is defined by the American Society for Testing Materials as follows: "Mixtures of hydrocarbons of natural or pyrogenous origin, or combinations of both, frequently accompanied by their nonmetallic derivatives, which may be gaseous, liquid, semisolid or solid and which are completely soluble in carbon disulfide." Asphaltic pyrobitumens, as defined by Abraham,2 is a species of pyrobitumen, including dark-colored, comparatively hard and nonvolatile solids; composed of hydrocarbons, substantially free from oxygenated bodies; sometimes associated with mineral matter, the nonmineral constituents being infusible and largely insoluble in carbon disulfide. Deposits of native bituminous materials are found scattered over the entire world, but many are relatively unimportant as far as commerce is concerned. No attempt has been made to cover all of the known deposits. The principal bituminous materials of commercial interest are: 1. Native asphalts, solid or semisolid, associated with mineral matter such as Trinidad Lake asphalt, Rock asphalt and Selenitza, Boeton and Iraq asphalts. 2. Native Asphaltites, such as gilsonite, grahamite and glance pitch, conspicuous by their hardness, brittleness and comparatively high softening point. 3. Asphaltic bitumens obtained from nonasphaltic, semi-asphaltic and asphaltic crude petroleum by distillation, blowing with air and the cracking of residual oils. 4. Asphaltic pyrobitumens of which wurtzilite and elaterite are of chief interest industrially as they depolymerize upon heating, becoming fusible and soluble in contrast to their original properties in these respects.2 5. Mineral waxes, such as ozokerite, characterized by their high crystallizable paraffine content. Native Lake Asphalt At Brighton situated in the southwestern part of the Island of Trinidad is one of the largest deposits of native asphalt in the world.3 The lake is oval in shape, covering an area of 114 acres and having a depth of 285 ft at its center. The material forming this deposit is an emulsion of water and bitumen with a suspension of mineral matter consisting of impalpably fine clay dispersed by nature in the asphalt, and small quantities of silica and vegetable matter. The entire mass of asphalt is in slow but constant motion as evidenced by the migration of islands of vegetation from one place to an-

Jan 1, 1960

By E. M. Wise

WHEN man became dissatisfied with the mere utilization of physical force and began to use weapons, he made a definite stride forward. At first he used sticks, animal bones and stones, often rudely shaped to some particularly lethal form. These devices, while crude, were moderately effective. How- ever, some of the brighter men of the tribe found that certain particularly heavy "stones" were somewhat ductile and could be hammered into more effective weapons than those previously known. Later, probably through the misuse of one of these weapons to stir the campfire, it was found that heating softened and perhaps actually melted the material. The process of annealing had been discovered! Smelting the more easily reducible metals was in all probability one of those fortuitous accidents which was followed up by thoughtful researchers who ultimately developed the technique of mixing various ores to produce bronze and even some of the nickel content alloys. The resulting products were at first lumps of more or less ductile material which could be hammered to shape, and were thus incidentally hardened by this process. The hardening of metals by alloying and cold working remained for many centuries the only known methods for improving their properties.

Jan 1, 1931

Adams, Bernard, Student, South Dakota School of Mines. Rapid City, S. D. '30 Ahlskog, Harold A., Student, Washington State College Pullman, Wash. '30 Aldridge, John, Student, New Mexico School of Mines Socorro, N M. '30 Almstrom, Adne A., Student, Met. Engrg., Washington State College Pullman, Wash. '29 Ancell, Virgil F., Student, Missouri School of Mines Rolla, Mo. '30 Ankudinoff, N., Mill Draftsman, Arthur G McKee & (:o., 2422 Euclid Ave., Cleveland, Ohio. '30 Apablasa, Salvador C., Student, Univ. of California Los Angeles, Cal. '31 Armstrong, Robert H., Student, Lafayette College Easton, Pa. '31 Armstrong, Thomas E., Student, Univ. of California Los Angeles, Cal '31 Aud, Robert A., Student, Lafayette College Easton, Pa. '30 Backus, Robert Small, Student, Mass.- Inst. of Tech . Cambridge, Mass. '30 Bailey, William C., Student, Univ. of California Los Angeles, Cal '30 Banning, Lloyd H., Student, South Dakota State School of Mines Rapid City, S D. '81 Barclay, M. G., Student, Colorado School of Mines Golden, Colo. '30 Barger, Thomas, Student, Univ. of North Dakota Grand Forks, N. D. '29 Barker, C. L., Student, Colorado School of Mines Golden, Colo. '30 Barker, Edgar Morgan. Student, Univ. of Utah Salt Lake City, Utah. '31 Barnwell, Earl E., Student, Oregon State College. Corvallis, Ore. '30 Bartholomees, Geo. C Box 304, Bonne Terre, Mo. '29 Bartholomees, Louis P., Student, Colorado School of Mines Golden, Colo. '30 Bary, Robert L., Student, Univ. of Kansas Lawrence, Kans. '30 Basham, Lester G., Student, South Dakota School of Mines Rapid City, S D. '31 Bates, Walter H., Student, School of Mines, Univ. of Utah .. Salt Lake City, Utah. '30 Beardshear, George T., Student, South Dakota State School of Mines.Rapid City, S D. '31

Jan 1, 1923

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

By Earl Chairman Oliver

The major development in stabilization of the oil industry during 1933 was the transition in the United States from state control to federal control in many of the functions that government is presumed to exercise. A brief review of the influences leading to that transition is given here to suggest its significance and to assist in forecasting its further development. Bitumens were known to the ancients and have been applied to minor uses since earliest historic times, but it was not until after the discovery of oil in considerable quantities near Titusville, Pennsylvania, in 1859 that it was made the basis of extensive commercial undertakings. In 1859 little was known about the origin of oil and gas, the nature of these deposits, and the physical laws that controlled their accumulation. Scientists soon began to study them, but 50 years or more of active oil-field development had elapsed before sufficient geological information had been accumulated to point the way toward efficient recovery of these products. In fact, only within the past five years has the function of reservoir energy become widely understood, yet it is a primary factor in oil recovery. discovery near Titusville, this infant industry has developed into an industrial giant. In complete ignorance of their destructive effect, wasteful development methods were initiated in Oil Creek and these became industrial habits. These habits in turn became oil and gas law. Under that law vast sums of money have been expended, rights have become vested and development methods fastened on a great industry that not only bring upon it periodic demoralization but cause ruthless destruction of the nation's reserves of these important natural resources. This is occurring in the midst of a petroleum era when oil is essential to the nation's security, its industrial supremacy, and the personal convenience of every citizen. Its conservation, therefore, has become a question of grave national concern. Conflict between PHysical Facts and Oil Law This destruction of an important natural resource and periodic demoralization of a vast industry can be halted only by readjusting oil

Jan 1, 1934

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By R. F. Mehl, W. Batz, C. Wells

L. S. Darken—It is indeed gratifying to find that the results of the two different methods here reported are in substantial agreement with each other and with the earlier work1 of two of the authors. Dr. R. P. Smith, of our laboratory, has been conducting some experiments at 1000°C to determine the diffusivity of carbon in austenite by a third method— the steady state method. This work, which will soon be reported, is far enough advanced that we can say it is in substantial agreement with that of the present authors. The only disparity which might be considered significant is in the high-carbon region, where we find that the diffusivity rises a little less steeply than indicated in fig. 8. F. E. Harris—The authors have presented an impressive arrangement of data concerning the diffusion of carbon in austenite. Of particular interest is the compilation, table IV, which is repeated in col. B of table V for direct comparison with values (col. A. table V) from a formulation using a single Q value of 31,000 cal as the activation energy for diffusion. This comparatively simple formulation has been used quite successfully in the practical application of calculating the carbon added (or removed) through the face in carburizing and decarburizing experiments, where the face concentrations are held quite constant for known times and temperatures. Literally hundreds of tests have been so checked where the computed and experimental values have varied by less than 5 pct. For higher temperatures, where proper carburizing data are hard to obtain, the diffusion couple is treated as a decarburization of the high-concentration bar and as a carburization of the low-carbon member. The analysis has been limited to a maximum of 1.40 wt pct carbon. The agreement between cols. A and B in table V may be considered fair, if a liberal viewpoint is taken. The use of a diffusion couple has one serious drawback, in that comparatively small amounts of carbon pass through planes of concentration close to those of the initial high-carbon and low-carbon members, and hence small errors become important. In addition to the sensitivity at these high and low concentrations.

Jan 1, 1951

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By B. M. Bird

ONE of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practise for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical danc-ing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1928

By W. R. Seyfried

The problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. The Process as Planned In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the company, first drafted a process in July of that year—five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or lour-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F). (b) The roasted ore would then be leached with hot aqueous ammonium bi-sulphate to form a slurry. In this way the

Jan 1, 1949

By Arthur L. Flagg

The Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of moderate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 Sq. miles, bounded on the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sea-level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet without railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a sligh degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction. At present all supplies and equipment are hauled in by wagon from Stites, a distance of 58 miles, over a wagon road constructed by the State in 1904, following in the main the old Nez Perce trail. While this is not a bad road, it is not all that might be desired. Starting at Stites at an elevation of 1,327 feet above sea-level, the road runs through low hills to Clearwater, a distance of 10 miles. In the next 16 miles the climb is steady until the Mountain House is reached, which is near the summit of Mount Pisgah. This is the highest point passed on the road, having an elevation of 6,500 ft. From the

Jan 1, 1914

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

The following is an incomplete list of members and guests who called at Institute headquarters during the period July 10, 1919, to Aug. 10, 1919. Howard C. Arnold, Washington, Pa. J. S. Lane, New York City, N. Y. L. M. Banks, Denver, Colo. H. W. Lawrie, Washington, D. C. George S. Blair, Pittsburgh, Pa. J. L. McAllen, Latouche, Alaska. Richard H. Catlett, Newark, N. J. David F. McFarland, Urbana, Ill. George L. Clark, Council Bluffs, Iowa. James F. Magee, Lancaster, Pa. Capt. Frederick S. Cook, Portland, Ore. A. G. McGregor, Warren, Ariz. John J. Croston, Atlanta, Ga. Emory M. Marshall, Santa Fe, N. M. Thomas Davis, Seattle, Wash. Benjamin L. Miller, Bethlehem, Pa. J. C. Dick, Salt Lake Cite, Utah. 2d Lieut. C. 0. Noble, U. S. Army. Chris. G. Dobson, Vancouver, B. C. Irving Perrine, Hutchinson, Kans. H. S. Emlaw, Grand Rapids, Mich. Fred S. Porter, Seattle, Washington. F. A. Fahrenwald, Cleveland, Ohio. Capt. H. R. Robbins, Peking, China Lieut. James L. Head, St. Louis, Mo. Joseph P. Ruth, Jr., Denver, Colo. A. A. Holland, Napanu, Canada. William A. Simkins, San Francisco, Calif. W. E. Hopper, Washington, D. C. T .V. Smirnoff, Siberia. Harry Hotchkin, Chicago, Ill. Harrison Souder, Cornwall, Pa. L. L. Hutchison, Tulsa., Okla. F. J. Sur, Denver, Colo. Paul S. King, Wilmington, Del. Harry Wolf, Denver, Colo. George K. Anderson, Jr., lies accepted a position as manager for Wight & Co., producers of air-cooled blast-furnace slag, at Longdale, Va. J. M. Armstrong, with the Caribbean Petroleum Co., has been transferred from Philadelphia to Maracaibo, Venezuela. Fred Sherman Baker, who has been with the Oriental Consolidated Mining Co., at Unsankinko, Chosen, Korea, is now at Columbia City, Ind. Ray J. Barber has removed from Roxbury, Mass., to New York City, and is now consulting engineer for the Roxbury Cold Mines, Inc.

Jan 9, 1919

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924