Search Documents

By G. H. Turner, R. C. Bell, E. Peters

Zinc oxide activities in a typical lead blast furnace slag have been calculated from plant operating data. These activities were used to assess the probable effect of fuel composition, oxygen enrichment, and air preheating on the efficiency and capacity of the slag-fuming operation. THE physical chemistry of zinc fuming has been examined with three objectives in mind: 1—to predict conditions favorable to increasing furnace capacity, 2—to predict the changes required to fume zinc more economically, and 3—to explain reported differences in the efficiencies of various slag-fuming plants. This study, made at ail in the plants and laboratories of The Consolidated Mining and Smelting Co. of Canada Ltd., developed from a program undertaken some three years ago on behalf of the AIME Extractive Metallurgy Div. subcommittee on slag fuming. Lead metallurgists first became interested in the recovery of zinc from lead blast furnace slags in 1905 and 1906. An excellent review of the early experimental work has been made by Courtney,' who described blast furnace, reverberatory furnace, and converter methods of fuming zinc from slag. Some of the investigators did not appreciate the importance of reducing the zinc oxide content of the slag to metal in order to fume it, since they tried compressed air blast without fuel in their earliest attempts. However, by 1908, the importance of reducing the zinc was established.' In 1925, the Waelz process for the recovery of zinc oxide from oxidized zinc ores was developed in Germany.' This process was not readily adaptable to lead blast furnace slags because of the difficulty in handling fusible charges in a kiln. What appears to have been the first slag-fuming operation as it is known was commenced by the Anaconda Copper Mining Co. at East Helena, Mont. in 1927." The first Trail furnace was completed in 1930, and this was followed by the construction of several other slag-fuming plants. During the period in which slag fuming has been extensively employed, little development of the chemistry of this process as a whole has taken place. Several good papers on the petrography of lead blast furnace slags have been published,""= but these studies could do little more than establish the forms in which lead and zinc occur in the initial charge and final products of the slag-fuming operation. In recent years, zinc-smelting problems have been ap- proached from a thermodynamic point of view. Maier has published an excellent thermodynamic treatment of zinc smelting." The important thermodynamic properties of zinc and its compounds have been determined and checked by other investigators.' However, to the best of the authors' knowledge, no thermodynamic treatment of the fuming of zinc from slag has been published. A thermodynamic study of any process requires that the essential chemistry of that process be known. In slag fuming there appear to be some differences of opinion as to whether the active reducing agent is elemental carbon or carbon monoxide. Furthermore, some observers have noted that high volatile coals appear to be more efficient than low volatile coals, indicating that hydrogen is also an important factor in the reducing efficiency of a fuel. That both hydrogen and carbon monoxide are effective reducing agents for the zinc oxide content of lead blast furnace slags can be demonstrated readily by introducing these gases into a slag bath held in a neutral vessel at 2100°F (1150°C). Elemental carbon also will reduce zinc oxide, but it is improbable that much free carbon is available for reduction of zinc, as the reaction between the finely powdered coal and air should be largely completed before the solid coal particles reach the slag. Some large-scale fuming experiments using gaseous hydrocarbons have been carried out by other investigators, but, as far as is known, these have not been developed yet into operating processes. The thermodynamic treatment in this paper is based on the following reactions: 1—to supply the thermal requirements C+V2O2- CO [1] C + 0,-CO, [2] H2+ ~z0,-H,O 131 and 2—to reduce ZnO ZnO + CO + Zn + CO, c41 ZnO + H, e Zn + H,O. [51 The furnace-gas composition also is controlled by the equilibrium constant of the familiar water-gas reaction H,O + CO + CO, + H2. C6l In order for the thermodynamic calculations to be quantitatively applicable, it is necessary that the chemical reactions to which they are being applied

Jan 1, 1956

By E. L. Bruce

GOLD occurs ill many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be confined to representative types of deposits, chiefly those of major importance; a few others, differing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwestern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubtedly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambrian gold deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By R. A. Perry

A speiss is an artificial arsenide, sometimes an antimonide, formed in lead smelting, smelting of oxide copper ores, and in some lead-refining operations. The production of speiss is closely allied with the amount of arsenic and metallic iron in the blast-furnace charge, while dross is produced mostly from the copper and sulphur, with varying amounts of antimony, arsenic and nickel. Most speiss is essentially an iron arsenide containing some sulphur, copper and nickel, if these elements are present in the furnace. The recent introduction of the soda treatment of lead drosses has produced a speiss high in copper. Speiss is not miscible to any extent with molten copper, lead, matte or slag. Miscibility increases with temperature. This property of the speiss is clarified in the latter part of this paper. Most speisses are produced in conjunction with matte and their sulphur content points to the solubility of matte in speiss. . Some plants have insufficient speiss to warrant separate treatment. When arsenic is high in the blast-furllace charge, there may be sufficient speiss to tap separately from the first settler. Arsenic From the foregoing, it is obvious that a study of the treatment of speiss would not ,be complete without consideration of arsenic. Inasmuch as perhaps go per cent of the blast-furnace feed may be sinter, a definite knowledge of the properties of arsenical ores and compounds that go in to the roaster and sinter feeds is of value. Lcad smelters obtain their arsenic from ores and concentrates, as well as from flue dusts shipped from other plants, particularly copper smelters. The percentage of arsenic in ores is usually low, although occasional lots of high arsenical products are smelted. These crude ores may be sulphides, as arsenopyrite; or oxides like scoiodite, which carry gold or lead minerals. The small amount of arsenic in the original ores received is greatly increased by a circulating load of arsenic in secondary products at are resmelted for their lead or precious metals. More important than the arsenic present directly in the concentrates treated is that in fumes and dusts that may originate in the blast furnace or sinter plant of the lead smelter, or may come from a copper smelter as lead-bearing converter fume or roaster dust. Thus the lead smelter not only must treat its own arsenic but is compelled to handie that from some copper and perhaps other lead plants. Where copper and lead plants exchange products, each plant may be forced to re-treat part of the arsenic it has shipped ,outside its own confines. Speiss from the lead blast furnace contains chiefly iron and arsenic with some lead, copper and sulphur and often appreciable amounts of gold and silver. If its copper content is sufficient this speiss may be sent to the copper smelter where usually it is treated in the converter and the copper is separated as blister. Much of the arsenic and most of the lead are recovered as converter fumes

Jan 1, 1944

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.' Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10' psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9'10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By Francis Foley

FROM the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.1 They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration. of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Westgren and Phragmèn3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 10, 1925

By R. H. Swallow, George Hess

The purpose of presenting this paper is to show: 1. The applications of aerial photography to the map requirements of strip mining. 2. The methods and procedures for producing accurate aerial contour maps. 3. The advantages of aerial contour mapping over stadia or plane table methods. Introduction Aerial photography was once a crude, uncertain tool. 'Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques. Then, some farsighted engineers and aerial photographers found that if the camera's axis were vertical to the earth's surface, these pictures could be the source of valuable mapping information. By viewing these pictures in stereoscopic pairs, accurate measurements could be made and contour maps produced from this aerial photographic base. So the aerial mapping business developed, using the plane and aerial camera to collect the data, working with skilled ground parties who established a network of ground control for this map information photographed from the air. Over the following years, a whole new science developed, known as photogrammetry. Precision cameras and lenses were perfected, and the narrow view of the surveyor's transit was broadened to the vast perspective of the mapping plane. Stereoscopic Coverage Obtained Today in making aerial topographic maps, aerial photographs are exposed so that full stereoscopic coverage for the survey area is secured. To obtain true elevations these photographs are processed through a series of precision measuring and contouring instruments which employ a principle similar to the military range finder. Here is how aerial mapping is being used by your industry. Topographic maps are but one of three products from aerial photographic surveys. First, there are the individual photographs. These are taken in flight strips, exposed with an overlap, just as shingle on a roof overlap. Exposures are overlapped from 55 to 60 pct along the line of flight so that a large part of the area in one picture also appears on the adjacent photograph. Successive strips are flown with a side-lap of between 20 and 25 pct. Each point on the ground thus will be somewhere near the center of at least one photograph in the series. They may be studied under a stereoscope and relief seen in a third dimensional effect. Geologic features that may go unobserved in ground exploration are often detected under stereoscopic inspection. Moreover, though field checking is not obviated with these aerial photographs, it is directed toward critical areas and toward worthwhile anomalies. Aerial Photographic Mosaics The second product of an aerial survey is the photographic mosaic. This is an assembly of carefully matched aerial photographs in mosaic form. Although not as accurate as the topographic map, it does reveal a wealth of cultural detail in true relative scale. Since the mapping plane is flown over the area at a fixed altitude, the peaks and valleys are pictured at different scales. During compilation these scale differences are compensated by adjusting one vertical picture to another according to plotted ground control positions. Only extreme variations in ground elevation cannot be

Jan 1, 1950

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By Walter P. Jenney

In the limestone area of Tintic and other mining districts of the Great Basin region of Utah, it has been observed that surface-outcrops of ore occur but seldom, and are mainly confilled to points of relatively low elevation, where the veins cross some basin or ravine. Nowhere does a considerable body of ore outcrop on the tops or high up on the slopes of the hills. Mining operations, on the other hand, have shown that large and continuous ore-deposits frequently occur in depth in the limestone, beneath large masses of barren rock. Such orebodies, when followed upward in the lodes, are found to terminate at well-defined levels, without reaching the surface. Yet the minerals-bearing fissures themselves extend above the top of the ore, being often traceable, though barren of all valuable minerals, for hundreds of feet above the stopes in the mines, and even observable in outcrops at the surface. This abrupt cessation of the ore at a uniform horizon does not appear to be connected with any change in the countryrock adjacent to the lodes. The strata above and below this horizon seem to be in every way equally favorable to ore-deposition. Explorations above it have developed an open-fissured country, barren not only of ore, but also of indications that minerals bearing gold, silver, lead or copper were ever deposited in the strata at that elevation. The height reached by the ore, while usually constant throughout the length of a given lode, may vary in particular sections, from the operation of local causes. Each lode in a district has its own distinct horizon, above which the oredeposits do not extend. Where the ore-bodies are continuous

Jan 1, 1903

By R. L. Bell, T. G. Langdon

A technique was developed- for determining the grain strain, and hence the grain boundary sliding contribution, occurring during the high- temperature creep of a magnesium alloy, from the distortion of a grid photographically printed on the specimen surface. The results were compared with those obtained from measurements of grain shape, both at the surface and interrwlly, and it was concluded that the grain shape technique may substantially underestimate the grain strain and overestimate the sliding contribution due to the tendency for migration to spheroidize the grains. ALTHOUGH a considerable volume of work has been published on the role of grain boundary sliding in high-temperature creep, many of the estimates of Egb (the contribution of grain boundary sliding to the total strain) have been in error due to the use of incorrect formulas or inadequate averaging procedures.' One of the most easy and convenient measurements from which to compute Egb is that of v, the step normal to the surface where a grain boundary is incident. Unfortunately, this parameter is also the one associated with the treatest number of pitfalls. Values of v have been used to calculate Egb from the equation: egb =knrVr [1] where k is a geometrical averaging factor, n is the number of grains per unit length before deformation, v is the average value of v, and the subscript ,r denotes the procedure of averaging along a number of randomly directed lines. If the dependence of sliding on stress were assumed, it would be possible, in principle, to calculate k from the known distribution of angles between boundaries and the surface. This in itself is difficult because the distribution depends on the history of the surface,' but the problem is even further complicated by the fact that v depends on other factors such as the unbalanced pressure from subsurface grains.3 However, the great simplicity of the measurement procedure for v makes it highly desirable that this problem of k determination should be overcome. In the present experiments, this was achieved by the use of an indirect empirical method in which the grain strain, eg, at the surface was determined by the use of a photographically printed grid. The assumption here is that the total strain, et, is simply the sum of that due to grain boundary sliding, egb, and that due to slip or other processes within the grains, eg. SO that: Et = Eg + Egb [2] Thus k is given by: In practice, it is customary to indicate the importance of sliding by expressing it as a percentage of the total creep strain; this quantity is termed y (= 100Egb/Et). The determination of Eg from a printed grid within the grains avoids the difficulties due to boundary migration which should be considered when the grain strain is calculated from measurements of the average grain shape before and after deformation. As first pointed out by Rachinger,4,5 however, this latter technique has the particular advantage that it can also be applied in the interior of a polycrystal. Recently, several workers have produced evidence on a variety of materials6-'' to support the observation, first made by Rachinger on aluminum,4,5 that 7 can be very high, 70 to 100 pct, in the interior, even when the surface value, determined from boundary offsets, is very much lower.10'11 Although there have been criticisms both of the shortcomings of the grain shape technique'' and of the different procedures used to determine y at the surface,' it seemed important to check whether measurements of sliding by grain shape gave values of y which were truly representative of the material. In the present experiments, grain shape measurements were therefore made both at the surface and in the interior for comparison with one another and with the independent measurements of grain strain using the surface grid technique. EXPERIMENTAL TECHNIQUES The material used in this investigation was Magnox AL80, a Mg-0.78 wt pct A1 alloy supplied by Magnesium Elektron Ltd., Manchester. Tensile specimens, about 7 cm in length, were prepared from a 1.27-cm-diam rod, with two parallel longitudinal flat faces each approximately 3 cm in length. The specimens were annealed for 2 hr in an oxygen-free capsule, at temperatures in the range 430° to 540°C, to give varying grain sizes, and, prior to testing, the grain size of each was carefully determined using the linear intercept method. This revealed that the grains were elongated -0.5 to 5 pct in the longitudinal direction. Testing was carried out in Dennison Model T47E machines under constant load at temperatures in the range 150" to 300°C. At temperatures of 200°C and below, tests were conducted in air with the polished flat faces coated with a thin film of silicone oil to prevent oxidation; at higher temperatures, an argon atmosphere was used. To determine v,, each test was interrupted at regular increments of strain and the specimen removed from the machine. At the lower strains, when v, was less than about 1 pm, measurements were taken on a Zeiss Linnik interference microscope;

Jan 1, 1969

By V. Lepetic, C. C. Harris

A systematic program of investigations covering all aspects of cell hydrodynamics,1-3 flotation kinetics,4,5 surface chemistry and their interactions has as a major objective the elucidation of the flotation micromechanism and the principles of cell design and scale-up.6 Purely from the scale-up point of view, a family of reactors should enable different throughputs of the same material to be similarly treated or, at least, to be treated in a manner which differs beween reactors in a predictable way. Thus, for the same material and residence time, the recovery and grade from differently sized cells of the same family should, ideally, be similar or, at least, be related to each other in a known way. It is well known, however, that different-sized cells do not always achieve similar results, and it is necessary to enquire into the reasons for these differences. For example, it may be that the relative dimensions of different-sized cells result in hydrodynamic conditions which preclude similarity; if so, different scaling may improve the situation. The major question concerns identifying the dynamic conditions and their associated geometric requirements which govern the flotation process, and the criteria which are necessary for their fulfillment. It is to answer such questions that the program referred to earlier was instituted. In connection with this program and in order to examine data concerning the physical features and operating conditions of existing flotation cells, the following survey was carried out. This work represents an approach which is complementary to experimental investigations, for it recognizes that the design of existing cells may embody several of the principles being sought. If data for enough cells, especially families of cells, are examined, some broad requirements common to all cells may emerge.

Jan 9, 1966

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

By James Boyd

REACTIVE metals are not only those sufficiently radioactive to be used as fuels, such as uranium and thorium, but all metals that will find application in power reactors. It is required of such metals that they be relatively inert or chemically unreactive, dimensionally stable at high temperatures and pressures, and either very absorbent of radioactivity or transparent to it. To gain the right perspective concerning these metals it is necessary at this point to explode some erroneous concepts propounded so often they have become accepted as fact. The first of these is that the great industrial nations, especially the U. S., have reached their pre-eminent position chiefly because they possess abundant mineral resources. Some U. S. mineral economists, echoed by the politicians, have taken this position so often that many of their theories and policies are based on the presence of developed mineral resources as a sine qua non to the country's greatness. Actually the reverse is true- under a social and political system granting free rein to the initiative and creativeness of its people, many hidden mineral resources that otherwise would have lain fallow have been developed into productive enterprises to the benefit of the national industrial economy. Again, once the proper incentive was furnished, other countries have also been able to establish valuable mineral enterprises in recent years; resources long dormant for lack of a proper economic environment suddenly have become valuable and productive. It is possible to name immediately several nations where such domestic economic developments have had favorable repercussions within the last decade. The absence of productive mines in any country is no indication that workable deposits do not exist within its territory.

Jan 11, 1957

By Frank R. Hunter

Introduction Scope of Work This paper represents the results of an investigation of the presence, amounts, and degree of concentration of heavy minerals found in the pulp of the phosphate flotation plant at Peace Valley, Fla., which is operated by the International Minerals and chemical Corporation of Chicago. In this paper, heavy minerals are those, excepting collophane, that sink in acetylene tetrabromide with a specific gravity of 2.95. Percentages of heavy minerals at several points of the flowsheet and the species of minerals have been determined. Some information as to the screen size of the minerals has been acquired. Previous Work All previous published reports or investigations of the deposits of heavy minerals in Florida have been limited to present beach sands. The mining operations conducted by the Humphreys Gold Corp. about seven miles east of Jacksonville along an ancient shore line have been described in trade journals, but descriptions of the minerals have been lacking. Commercial grades of ilmenite, zircon, and rutile are produced on a large scale. Papers have been published on heavy minerals found on the Florida beaches.1-6 Location "International's" Peace Valley flotation plant is in south-central Polk County, Fla. about eight miles south of Bartow and along the Atlantic Coast Line Railroad. The mine surrounds the plant and includes about 1500 acres of the phosphatic lands in this area. Geology General Setting All of the rock underlying the area is almost horizontal. The oldest bed exposed is part of the Hawthorn phosphatic limestone of Miocene age. This outcrops in the stream bed of the Peace River about one mile east of the plant. Elsewhere the Hawthorn is covered except where it has been exposed by mining operations. The Bone Valley formation of Pliocene age, which is the phosphatic stratum extensively mined in this area, unconforma-bly overlies the Hawthorn. Resting unconformably upon the Bone Valley formation are Pleistocene (?) terrace deposits of unconsolidated quartz sand which comprise the overburden of the phosphate ore. Stratigraphy Hawthorn formation: "Bedrock" of the pebble phosphate deposits is a cream to white colored, sandy, dense limestone containing varying amounts of small grains and nodules of collophane. The upper surface of the formation is undulating and irregular showing evidence of former

Jan 1, 1949

By Henry C. Freeman

During the early period of the construction of the Illinois and Michigan Canal, about 1838, in excavating for the canal, where the present town of Utica stands, hydraulic limestone was discovered, and its value was recognized. A kiln for calcining and a mill for grinding were erected, and the cement was used in the construction of the locks of the canal. This property was subsequently bought by the present owner, Mr. James Clark, and the work has been continued to the present time in much the same primitive manner as it was begun. The bed is exposed in the Illinois River valley by stripping off a few feet of the covering rock. It is from 4 feet to 6 feet 9 inches thick, and nearly level, dipping gently to the northeast. The Utica Cement Company's establishment, which is two miles west of Utica and two miles east of La Salle, was an outgrowth of the Illinois geological survey. The writer was in charge of the district which included La Salle county, and, in working out the details of the geology of that county, discovered, below the Utica bed, another workable hydraulic limestone, which makes its appearance in the northern bluff of the Illinois River valley, rising above the water level at the point where the company's works are established. This cement group, of which there are several thin beds, lies just below the St. Peter's sandstone, with a few feet intermediate of transition-rock, which appears to represent the Calciferous, and is exhibited in place, in concretionary form, at the top of the bluff. The hydraulic beds are very regular, and the one worked by the company is 10 feet thick; or, speaking more definitely, there are two beds, separated by 18 inches of sandstone, lying about two feet above the bottom, and the two beds are worked as one, the sandstone being first cut out and removed, to prevent mixture. In 1869 I was invited to join with a company, and to take charge

Jan 1, 1885

By P. A. Boeck

The thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste. Advantages of Insulation It is not necessary in this practical and utilitarian age to enlarge upon the need of prevention of heat losses, but attention may advantageously be called to the other benefits derived simultaneously with the saving in fuel and the increase in thermal capacity of furnaces when properly insulated. In most industrial furnaces—which are here spoken of in the broadest sense, indicating general high-temperature equipment for any purpose and heated in any manner—the operations are generally carried on through a temperature range which has been found by practice to give the most ef-

Jan 1, 1916

By P. Duwez, H. Martens

Dimensional changes generally occur during the sintering of metal powder compacts. These changes may have several causes and their magnitude depends upon the numerous variables involved in the process, such as the nature of the powder, size and shape of the grains, compacting pressure, rate of heating, maximum temperature, length of time at temperature, and furnace atmosphere. Among all the variables, time, temperature, and compacting pressure are probably the most important ones, and the effect of each one of the other variables can be studied separately once the effect of these is well understood. The most precise method of studying the phenomenon of dimensional changes in a compact consists of heat treating the compacts at various temperatures for different lengths of time. In this method, only very small specimens can be used, in order to achieve rapid rates of heating and cooling. The technique involved in these measurements is very simple, but is time consuming. Another experimental approach to the problem consists of measuring the change in length of a compact as it is being heated at a constant rate. Although the two variables, time and temperature, are combined into a single one (rate of heating), the results obtained by this technique may be of great interest from both practical and theoretical points of view. The purpose of this paper is to describe a systematic investigation of the change in length during sintering of compacts made of one or several metal powders. Experimental Procedure The change in lenght of compacts during sintering was measured with an automatic recording dilatometer. In this instrument the change in length and the temperature are recorded as functions of time on two separate charts and the rates of heating and cooling may be varied from 1 to 20°F per min. The temperature may be kept constant at any value up to 2200°F during any predetermined length of time and the change in length recorded as a function of time. Provision is made for atmosphere control inside the fused silica tube containing the specimen. Three different magnifications are provided, so that 1 in. on the chart corresponds to 0.002, 0.005, or 0.010 in. change in length. The mechanism following the change

Jan 1, 1950

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By Francis B. Foley

From the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.&apos; They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Weatgren and Phragmen3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 1, 1926

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron&apos;s papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.&apos; Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron&apos;s two papers practically amount to a summation of his life&apos;s work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron&apos;s valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author&apos;s reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By S. E. Buckley, M. C. Leverett

THE production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. INTRODUCTION Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,1 and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. ROLE OF DISSOLVED GAS When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1941