Search Documents

By C. E. Agnew

The Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P. Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formerly he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By W. H. Kantner

IN this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change sub-sidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the sur-face to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the east and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody-which is on the northwest side-is 600 ft. southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T' dT' ?T' ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

ALTHOUGH iron ores occur in many parts of Sweden the two principal deposits are those at Grängesberg (see accompanying map) and at Kiirunavaara-Gellivare. Both of these deposits are con-trolled by a holding company, Trajikaktiebolaget Grängesberg-Oxelösund, which sells annually about one-half of, the iron in ore traded in world markets and has a fleet of 24 seagoing ore boats, with a total dead weight capacity of 172,500 tons. Because of its pre-eminence in international iron ore trade a brief outline of its operations will be of interest. ORE DEPOSITS OF GRÄNGESBERG The Grängesberg deposits have been known since the Middle Ages, but up to the middle of the nineteenth century the ore was transported from the mines to the furnaces in winter in. sleighs. Railway building began in 1853, and in 1873 the complicated structure of capital investment was tottering, but the basic bessemer process created a demand for ore high in phosphorus, as this is, and refinancing on the initiative of Sir Ernest Cassel put the principal operation on a firm footing. There are numerous property owners in the district, but they are all controlled by a joint administration board, and 90 per cent of the ore is produced by a subsidiary of the Grängesberg company from proper-ties which it either owns or leases. The ore, a mixture of magnetite and specular hematite, is in lenticular bodies, dipping about 70 E. in. fine-grained gneiss, and contains about 61 per cent Fe and 1 per. cent. P. There are two principal veins; the total ore reserves to a depth of 500 meters are estimated at 150,000,000 tons. As seen in the accompanying illustration, the ores were first worked in open cuts, but eventually underground shrinkage stoping was adopted. Difficulties were encountered in the support of the workings and from the freezing of the ore in the stopes, so slicing was adopted, although block-caving is used in one place. Most of the mining is now done at a depth "of 150 to 190 meters. The present annual output is about 1,400,-000 tons of crude ore, which yields about 1,000,000 tons of concentrate after being subjected to magnetic con-centration and jigging.

Jan 1, 1927

By John Rear Admiral Edwards

Introductory.-There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived the thought of transporting petroleum by pipe line, conserving the by-products of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its Supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause. which 'prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle Top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States' Commanding Position as a Petroleum Producer.¬ In the study of the various problems relating to the world's production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects the most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 9, 1914

By John R. Edwards

Introductory.—There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived 'the thought of transporting petroleum by pipe line, conserving the byproducts of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause which prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States' Commanding Position as a Petroleum Producer.— In the study of the various problems relating to the world's production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects thc most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 1, 1915

By Nathaniel Herz

(San Francisco Meeting, September, 1915) THE use of zinc dust for precipitating the precious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been clone on methods of testing zinc dust, as yet no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some observations made while testing. a large variety of zinc-dust samples in the laboratory. W. J. Sharwood1 has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J. E. Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of `99 0' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more KCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 cc. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grains of pure crystallized KAg(CN)2 may he dissolved in a liter of water and 1.5 grams KCN added. "Weigh out 0.5 grain zinc dust into a 300-cc. beaker. Add a few cubic centimeters of water and stir until, zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, plaice in a scorifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efficiency."'

Jan 8, 1915

By Henry D. Hibbard, Edward L. Ford

The process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon, which could be done on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls. Since Holley's paper, important improvements have been made from time to time in both plants and methods for washing iron, and the

Jan 1, 1916

By Dr. O’Neil Thomas J., Donald W. Gentry

Introduction “A Western mine is a hole in the ground owned by a liar. . ." -Mark Twain THE CAPITAL INVESTMENT DECISION Decisions pertaining to a firm's proposed capital investments can have vital short- and long-term consequences on the organization's ability to compete, and even survive.Capita1 investment decisions, in general, center around two fundamental activities: (1) allocating capital funds to specific investment projects or assets, and (2) obtaining necessary financing in such proportion as to increase the overall value of the firm. In essence these activities or decisions describe the science of finance (as contrasted with economics). Fimnce has been described in general terms as the study of how a present, known amount of cash is converted into a future, perhaps unknown, amount of cash (Archer, Choate, and Racette, 1979). Fundamental to understanding the science of finance and the capital investment decision process in general are the basic concepts relating to cash flow transactions, time, income generation (markets), expected returns, and risk. The functions of finance may be segregated into three fundamental decisions which a firm must address: (1) the dividend decision, (2) the financing decision, and (3) the investment decision. These decisions are interdependent and their joint impact on the objective of the firm must be considered. This book primarily addresses the concepts and components associated with the investment and financing decisions as they affect the practice of mine valuation. Responsibilities of Management A primary assumption incorporated in this book is that the fundamental objective of any firm is to maximize its value, or wealth of its owners (stock- holders). Here, the term wealth refers to the total current market value of the firm's assets. In the case of corporations, the wealth or value is considered to be represented by the market price of the firm's common stock. The price of the firm's common stock obviously will be affected by its investment, financing, and dividend decisions. Consequently, an optimal combination of these three decisions should maximize the value of the firm to its stockholders. It is important to point out that wealth maximization is a more appropriate and inclusive goal for the firm than profit maximization. Indeed, there is a difference between the two objectives in most situations. For instance, a firm can always raise profits by selling stock and investing the proceeds in treasury bills or certificates of deposit. This type of activity, however, would rarely cause net shareholder wealth

Jan 1, 1984

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By A. L. Bollens, R. H. Johnson

The appraisal of oil wells, now that we have the age-size method of making composite decline curves, and the present worth of successive time units method of valuation, has its greatest remaining uncertainty in the difficulty of extending into the future the price curve and the composite production curve. The point of attack in this paper is the carrying on (or extrapolation) of the production curve. Led by the valuable discovery of Lewis and Beal that the decline curve is nearer the hyperbolic class, y = (x + a)-", than any other form, the current practice is the graphic method. The data are plotted on logarithmic paper and shifted with successive trials until the line becomes straight. This straight line can then be extended into the future. The method was a great help during the period when, for tax purposes, there was need for a quick method even though the errors were large. Now that we seek greater validity in our methods we find the following faults with the current method. 1. Where the shift is great (it exceeds 10 in some cases) the scale cannot be read with the necessary precision so that the resulting data would give a very irregular and inaccurate curve. 2. Where the curve cannot be straightened on logarithmic paper because of sigmoid shape the method has a serious systematic error. We believe the sigmoid curves to be more common than usually supposed, indeed when one considers the number of variable causative factors this is to be expected. We have therefore been seeking a method that is free from these difficulties and yet not so laborious as fitting a curve to the data and the calculation from the formula which, since it involves looking up logarithms, is unduly time-consuming. The method here described has been developed on the basis suggested by Earl Oliver, that the amount of oil produced per month or year for each reduction of production of a barrel of oil per day could be plotted to advantage. A step forward was made by Earl Carpenter in this laboratory, and some of the

Jan 1, 1928

By W. G. Matteson

IN 1915, the State of California passed a law of great scope and importance. This law has been in successful operation for., year and may be briefly described as an act "establishing and creating a department of. the State Mining Bureau for the protection of the natural resources of petroleum and gas from waste and destruction through improper operations in production; providing for the inspection of petroleum and gas wells; requiring all persons operating petroleum and gas wells to make certain reports" and providing the necessary officers and assessments-to carry out the provisions of the act. The statute provides for a separate department of the State Mining Bureau, under the general supervision of the State mineralogist, with a staff composed of a "state oil and gas supervisor" and four deputies. It rules that all petroleum and natural gas wells shall be drilled, operated or abandoned under the supervision of the State supervisor, who shall order such tests or remedial work as seems to him necessary to protect the interests of property owners and the general public. It also provides for a board of arbitration to consider orders given by the supervisor which are not acceptable to the well owner. Section 18 of the, act, which is the provision that is directly related to, this paper, requires "the owner of any well referred to in this act to keep a careful and accurate log of the drilling of such well;" and further requires that this log shall show the character and depth of the formations passed through or encountered in the drilling, particularly the location and depth of the water-bearing strata; the character of the water encountered (so far as ascertained); whether the water was shut off, and, if so, at what point; that it shall show completely the amounts, kinds and size of casing used; the depth at which oil-bearing strata are encountered; the depth and character of the strata, and whether all water was successfully and permanently shut off so as to prevent percolation or penetration into the oil-bearing strata. -

Jan 2, 1917

By Eric R. Morgan, J. C. Shyne

STRAIN aging is the name given to time-dependent changes which occur in the properties of cold-worked metals and alloys during storage. These changes are best observed through a study of mechanical properties, as illustrated in Fig. I for low-carbon steel. The effects of strain aging are usually regarded as being detrimental, particularly in deep-drawing steels. For example, an increase in yield strength and loss in ductility lead to buckling and tearing during drawing. At the same time the return of the yield point results in the formation of Luders bands or stretcher strains during the pressing operation. As a result of these effects many attempts have been made to eliminate strain aging from low-carbon steel. The problem still remains, however, because all known methods of preventing strain aging result in a more costly steel. The present work is an assessment of the situation in terms of theoretical, practical, and economic factors and suggests a new solution to the problem. Previous Work According to the Cottrell theory,' strain aging in a-iron may be regarded as the migration of interstitial atoms to free dislocations and the anchoring of dislocations by the resulting atmospheres. It may be concluded that the important factors which will govern the degree of strain aging are the diffusivity, the effective amount of interstitial element in solution, and the time of aging. The diffusivities and effective amounts of carbon and nitrogen in solution in low-carbon rimming steel are such that significant aging occurs in a few hours' storage at room temperature. Strain aging in deep-drawing steels cannot be controlled by controlling the time of aging because in commercial practice this is determined by economic factors concerned with inventories and may be several weeks. The diffusivity of nitrogen is twice that of carbon at room temperature but the diffusivities can be controlled by controlling the storage temperature. The retardation produced by only a 25 °C drop in temperature is significant but the cold storage of large steel inventories is an impractical solution to Table I. Analysis of Base Materials Alloy Pet C Yet 0 Pet N Vac 0.0037 0.052 0.0003 H 0.0044 0.013 0.0008 C 0.06 0.0014 0.0001 the problem. By far the most simple and effective ways to control strain aging are through control of the amount of carbon and nitrogen in solution. This may be effected through alloying, controlled precipitation, or by eliminating the carbon and nitrogen. Consider first the control of the amount of carbon in solution. The simplest approach would be alloy -ing in which strong carbide-forming elements are added. Examples of this approach are the additions of titanium' and niobium9 0 steel. These elements also combine with nitrogen and oxygen and when added in sufficient quantity result in a completely killed and non-aging steel. They are, however, impractical additions because they result in a costly steel. Carbon and nitrogen are often removed from iron on a laboratory scale by annealing in wet hydrogen, but because of cost this process has never been adopted on a commercial scale. In practice the amount of carbon in solution is controlled by the rate of cooling from the annealing temperature (710°C or 1310°F). In commercial box

Jan 1, 1958

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By G. D. Van Arsdale

THE paper of Mr. Posnjak presents a laboratory confirmation of the well known facts that air ox-idation of pure solutions of ferrous sulfate is slow and difficult and that, like many other similar reactions, the speed, may be greatly accelerated by the presence of other substances, often in very small amounts, the effect of the presence of copper being determined ex-perimentally in this case. However, it should not be. overlooked that copper is always present in heap leach-ing solutions in amounts equal to or greater than those in the experiments described; therefore the paper may be considered as an explanation of present results rather than a possible improve-ment to be added to present practice. It is not practicable and it does not pay to precipitate copper by ce-mentation below a point about 5 lb. per 1000 gal., equivalent to about 0.0005 mol. Cu. per liter, compar-ing with the approxi-mately 0.0009 mol. per liter of curve 2 in the diagrams given of course, also, in the heaps local concentrations are usually very much higher than this, which is also true of the effluent li-quors, so that I feel that it is safe to say that copper is already present in amount sufficient to realize, as large an accelerating effect as is practicable. Too much im-provement or refinement cannot be expected in a method of this kind, due to commercial limitations. It should be remembered that chemically and physically there is no sharp dividing line between leaching in place, heap leaching, and the usual tank leaching practice, practi-cally the same reagents being used in all three. From the viewpoint of extractions, etc., it is not common sense to apply leaching in place to an orebody carrying enough copper to pay for mining; and the same is true of heap leaching, for an ore carrying enough to pay for the crushing, handling, etc., of ordinary leaching. That is to say, leaching in place should properly be consid-ered only for an ore too low-grade to pay for mining, and heap leaching for the next higher grade, still how-ever too low-grade to pay for crushing and other re-finements. There is no advantage in leaching without mining or in heap leaching except lower cost of in-stallation and handling; on the other hand there are very distinct disadvantages which are inherent and which should prohibit their use except where necessity requires. The object of metallurgy is to make money out of the handling of ore, and it is purely a question of money as to how far we can go in "improving" or

Jan 7, 1927

By Harry Roeser

Short cuts for determining the constants of oil decline curves, with the method of least squares as a starting point, are presented and applications made to practical examples. The nature of the raw data does not justify rigid adherence to the orthodox theory but does lend justification to convenient methods of approximation within reasonable limits. If the conventional form y = kxn were changed to y = k(x + c)&apos;, methods of determining the curves would be simplified and greater uniformity in calculated results would probably follow. As A result of the publication, several years ago, of some articles on determining the constants of empirical formulas, the determining the constant&apos;s of types of curves used for estimating the production decline of oil wells was brought to the writer for study. Methods requiring a minimum of time and labor and a maximum of rigor were sought, as it appeared that the nature of the data from which such curves are computed and the relative uncertainty of occurrence of the events predicted from them did not justify close adherence to the theory on which the solution of such problems is ordinarily based. The technical deficiencies of the solutions presented in this paper, from the standpoint of the method of least squares, are readily apparent to those familiar with that method, but their presentation in detail here is irrelevant to the subject matter. However, it is the author&apos;s conviction, after a rather exhaustive study of the problem, that the value of the solutions lose little by the approximate application of the conventional theory. It must be understood by those who use these formulas that the solutions herein given, and the formulas based on them, are merely facilities to aid the valuation engineer in forecasting future events. It is assumed, also, that before application is made of them, prescient judgment based on the circumstances in each case, shows that the forecast has some probability of realization. On this basis only will these formulas be found useful.

Jan 6, 1924

By Louis V. Bender

AfteR investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled, is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds&apos; time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 191/4 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting. After the run of three months, the roof was in excellent condition. At the back of the furnace the bricks were not cut into at all; at 30 ft.

Jan 1, 1915

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry&apos;s law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2&apos;= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,&apos; using Laitinen and Liu&apos;s&apos; value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,&apos; and the equations of Wagner and Werner,&apos; the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O&apos; and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies&apos; have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969