Search Documents

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the' shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress 'system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical' specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By A. Cochardt, D. H. Feisel

HE success of the sintered aluminum powder material (SAP)' in raising the maximum useful temperature of aluminum alloys has stimulated effort in investigating similar systems in which the metallic matrixes have higher melting points. Examples of such systems which have been studied are nickel-alumina,2, 3copper-silica,4 copper-alumina,4 titanium-cerium oxide,5 and 80/20 nickel-chromium,8 cobalt,= and molybdenum7 matrixes with various hardeners. Conventional precipitation-hardened high-temperature alloys are often thermally unstable in service. The original fine particles that are responsible for good strength properties grow in size at elevated operating temperatures, a process termed "over-aging." This growth of precipitated particles causes a gradual loss in strength properties. A previous paperb describes the factors that govern the process of overaging, and estimates the time required for overaging of a nickel-alloy matrix dispersion-hardened by various precipitates such as are found in current high-temperature alloys, and by alumina. These calculations indicate that nickel-base alloys hardened with Ni3Al, Tic, or TiN are quite unstable at 1340" F (727°F). Such alloys should overage within a few hours at that temperature. A nickel-base alloy hardened with alumina, on the other hand, should behave differently. It should not overage appreciably within a thousand years. It was further shown8 that the thermal stability of the oxide-hardened alloy is mainly due to the low solubility of oxygen in equilibrium with alumina in the nickel-base matrix. Since the oxygen solubility is small, little oxygen can diffuse, and structural changes require very long times. This paper illustrates the effects of time and temperature on the structural stability of nickel alloy matrixes hardened by dispersions of Ni3A1, Ni3Ti, Tic, and alumina, and of nickel-chromium matrixes hardened by alumina. Hardness measurements and metallography have been used as a measure of structural stability. EXPERIMENTAL PROCEDURE Using the best information from published phase diagrams,'-l4 compositions of the Ni-Al, Ni-Ti, and Ni-Ti-C alloys were determined so as to have 5 vol pct of precipitate at 1350° F(732°C), the temperature selected to illustrate the effect of time on structural stability. Table I lists the chemical compositions of these alloys. Standard laboratory melting and alloying techniques were used in preparing ingots of the F-Series of alloys. The cast ingots, 1 3/4 in. in diam, were forged to 3/8-in. diam rods.

Jan 1, 1960

By J. E. Norton

Production statistics show that during the period of emergence from the depression the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1937 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechanization program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. Summer Work An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the accelerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con cerning the coal industry to the undergraduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war scrambled badly the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid development in some men. We could readily single out the men at the opposite ends of the scale of competence. Comprehensive Training Program Having adopted summer work as a means of interesting undergraduates, the Location Weeks Introduction............................... I Underground mining operations............... 27 Coal preparation............................ 24 Inspection—safety, mech., prep............... 31 Mine engineering and survey................. 16 Industrial relations.......................... 12 Operating staff—costs, time study............. 8 Miscellaneous............................... I Total.................................... 120 problem of attracting graduates was met by establishing a training program that covered approximately 120 weeks and

Jan 1, 1949

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 3/4 million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done' on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

L. C. Graton, Cambridge, Mass.—The subject of chalcocite occur; rence and its geological significance has, of course, a very important commercial bearing, as shown by the recent remark of a hard-headed mining .man: "This secondary enrichment business is one thing you geologists have put up which we can hang on to, and come out right." Most enrichments of copper ores depend upon the formation Of chalcocite from leaner sulphides. Recently it has been shown that not only does there exist this secondary or derived chalcocite, * but that in certain ores the mineral is present as an initial or original constituent, which therefore we may call primary. The desirability of distinguishing between these two kinds of chalcocite is evident and has recently been emphasized. That constitutes the first problem in this connection. I believe many who are working upon secondary enrichment of mineral deposits are giving much attention to that particular question. It is now possible to distinguish primary from secondary chalcocite in many cases. In such cases, what do we know of the' conditions under which this secondary or derived chalcocite was formed? , This is the second main question in connection with the subject. It is now plain, at least in many instances, that the formation of this derived chalcocite represents a phase of oxidation if we have in mind the primary ore as the thing acted upon. The next important question—and it is most important—is: does such oxidation go on above the zone where the rocks are saturated with water—that is, above the water level—or below, or indiscriminately above and below? Many of you have, or have had, opportunities to study at first hand, day after day, occurrences that' enable valuable conclusions to be drawn upon these and other important questions concerning the formation and significance of chalcocite. It is greatly to be hoped that your testimony will be made available and undoubtedly it will go far toward clearing up some of these doubtful points. John D. Irving, New Haven, Conn.—A short time before this meeting was called, H. V. Winchell, who was unable to be present, requested me to exhibit and describe these two samples of pyrite. (Exhibiting specimens.) They consist of fragments of pyrite inclosed in two small bottles. The first bottle shows fragments of pyrite which were immersed in water carrying copper sulphate but without SO2 for a period of two years. They remained comparatively clear and bright. No chalcocite has been deposited on them. The second bottle shows fragments of

Jan 1, 1915

By George S. Rice

DEFINITE data on the amplitude and effect of ground movement in specific mineral formations, caused by various methods used in the mining of ores, coal, and nonmetals, or in the extraction through wells of petroleum, sulphur, and soluble salts, are increasingly needed because of legal liabilities from damage to overlying or adjacent properties, and growing concern as to the conservation of national mineral resources. Not since the committee was established in 1923 has it been so difficult to get technical papers giving ground movement and subsidence data from specific mine operators. The reasons given, as above indicated, are pending or threatening lawsuits. There are three major objectives in ground movement and subsidence studies : (1) Maximum recovery of a mineral resource. (2) Minimizing damage to surface structures, highways, railroads, and agricultural lands caused by caving or subsidence, which may in some situations, as along the Gulf of Mexico shore, cause flooding by surface waters. (3) Lessening damage to overlying or adjacent mineral by back-filling of mine excavations as completely as possible.

Jan 1, 1940

By W. S. Gillam

A need for new supplies of fresh water exists today and in many specific areas that need is urgent. One solution lies in saline water conversion, a problem complicated by cost factors. The principles involved in saline water conversion, the status of development, and the estimated costs (present and future) of several processes are presented. Among the methods discussed are distillation, electrodialysis, and freezing. In general, the costs presented are based on a standardized procedure for estimating conversion costs, permitting a valid comparison among the various processes. The need for new supplies of fresh water and the potential benefits to be derived from an abundant supply of converted water are recognized by practically everyone concerned with water problems. The water supply problem exists today; it is urgent in many specific areas in this country and also in the world, and it will become more acute in the future. One answer to the growing problem of adequate water supplies is the development of new sources. Very significant quantities of brackish underground and surface waters exist in certain areas and an inexhaustible supply of ocean water is available. Thus in many areas water resources can be extended through saline water conversion. Congress recognized the need for new sources of fresh water in 1952 and passed the Saline Water Act, Public Law 448, amended it in 1955, and in September 1958, enacted Public Law 85-883, calling for the construction of at least five demonstration plants. The program is administered by the Dept. of Interior through the Office of Saline Water, and its primary objective is to reduce the cost of converted water produced, whether it be by development of new processes or improvement of known processes. This is a most difficult problem and one that will require several years of prodigious effort. It is difficult—not because of any intricate or new chemistry, engineering, or physics involved—but because of the difficulty in converting water at low cost. Whatever the sources of the saline water, the salts which are held tenaciously in solution must be removed before the water becomes suitable for industrial or domestic uses. Saline water is a relatively simple system of salts dissolved in water. It has certain chemical and physical properties that determine the various methods by which the salts may be separated from the water. The system, although not complex, in most instances, has had countless years in which to reach equilibrium and is, therefore, comparatively stable. Because of its stability, separation of saline solutions requires relatively large quantities of energy. The unique properties of water depend on the fact that its molecules are chemically active. The chemical and physical properties of water are associated with the type of bonding involved in the water molecule. Chemical changes such as hydrolysis, or rusting of iron, involve the breaking of chemical bonds between the hydrogen and oxygen atoms. Physical changes, such as evaporation in a boiler, the melting of ice, or the viscous resistance to flow in a pipe, involve breaking of the hydrogen bonds. (The hydrogen nucleus is so small that it can attract two negative atoms.) Thus water molecules not only combine with molecules of other compounds but even with one another; e.g., each molecule may be bounded to four other molecules. Water molecules cling to the ions of dissolved salt to form water-encumbered hydrated ions and they cling to one another to form entangling networks through which hydrated ions can be propelled only by tearing the networks apart. That is one reason why considerable energy still needs to be expended in our simplest procedures for purifying water. If water molecules did not have this habit of clinging so tenaciously to other molecules, and to one another, it would be easy to push salt ions past the water molecule and get a separation. But the water would not then dissolve salt, so the problem would not exist.' Water when heated evaporates very slowly, relative to other liquids having simple molecules. Vaporization involves the separation of molecules from the liquid, and this means overcoming the attraction between molecules which is due to the hydrogen bonding. The heat of vaporization for water is high; consequently, the boiling point of water is also high. Water boils at 100" C; hydrogen sulfide (H2S) at -60" C; oxygen (02) at -183" C; nitrogen (N2) at -196" C; and methane (CH4) at-161°C, even though the latter has about the same molecular weight as water. Because of these peculiar properties of water, it exists as a liquid on earth instead of a gas such as hydrogen sulfide or nitrogen and oxygen.

Jan 1, 1961

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

By C. Richard Honeycutt, Frederick C. Langenberg, Guenter Pestel

Otto Schaaber (Institut für Harterei-Technik, Bremen-Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Incr ase imports. 3. Develop new sources such as synthetic liquid fuels. All three courses may well be needed, as it is doubtful that any one of the three alternatives alone can satisfactorily solve the problem indicated by the prevailing trend in demand for oil. Curtailment of oil consumption is not a constructive policy, except where oil is being wasted or coal can be readily substituted as in stationary steam plants. Reduced oil supplies for most uses will curb our economic advancement and, in addition to inconveniencing consumers, will have a pronounced adverse effect on American industry. The oil-burner-manufacturing industry already has been dealt a hard blow. Shipments in the first 5 months of 1948 decreased 70 pct from those in the same period in 1947.1 The effect of a similar cut in the automobile industry can be imagined. A severe prolonged shortage of gasoline could seriously disturb our present economic well-being. It might be pointed out also that even the prospect of a shortage or lack of assurance for the future can discourage buyers of equipment, as occurred in the case of oil burners. An increase in our imports of oil seems to be a necessary expedient for the immediate future. Its advantages are that it will require a minimum of manpower and steel in a time of critical shortages and will conserve domestic reserves. Any major dependence upon foreign sources for our oil supplies should be avoided, however. Other nations are increasing their oil consumption more rapidly percentagewise than the United States and eventually will compete with us for the not unlimited world supplies. In peacetime, foreign countries might restrict ship- ments of oil to this country or impose exhorbitant prices. In the event of war, there is serious danger that such sources would be cut off, and American-developed oil fields overseas might even be used against us. Although synthetic fuels cannot relieve any oil shortage that might develop within the next year or two, an immediate start toward a substantial synthetics industry to supplement petroleum not only could help relieve shortages several years hence but also would help establish the much needed "know-how" for large-scale production. By assuring ample future supplies, such a start would permit sound planning by industries dependent upon oil and maintain or restore the confidence of prospective customers for oil-con-suming equipment. If it is agreed that domestic production of crude oil cannot be expected to meet future domestic demands, that oil rationing in general is undesirable. and that too great dependence on foreign oil should be avoided—and the weight of the evidence supports such conclusions—it is inescapable that commercial synthetic fuel production should be developed to supplement domestic petroleum supplies, which, of course, will furnish the bulk of our requirements for yean to come. Sources of Synthetic Oil The three principal sources of synthetic oil are natural gas, oil shale, and coal. A commercial plant using natural gas is under construction, and expansion of this industry is expected.

Jan 1, 1950

By C. P. Watson

It is perhaps significant that a few years ago the sessions held here were chiefly occupied with production. In the last two years these sessions have been concerned with production curtailment, unitization and conservation, notwithstanding that production in the United States in 1929 reached a total in excess of 1,000,000,000 barrels. A study of the leading producing units in the United States shows that Oklahoma, Texas and California in 1929 yielded 84 per cent. of the total production from 33.5 per cent. of the total number of producing wells. Production in the United States in 1929 showed an increase of 107,000,000 bbl. over the 1928 figures. This increase in itself perhaps is not enough to have caused the serious situation that is now confronting the industry. However, taking into account the gradual encroachment on the consumption of fuel oil through the greater utilization of natural gas, probably we have reached the point in the United States where prices will determine to a large extent,' in 1930, the amount that will be produced. In the states of Texas, Oklahoma and California, the most significant developmcnt of 1929 has been the desire of operators to reach some agreement to bring production more or less in control with the estimated demand. In November, production in California, particularly in the Santa Fe Springs field, was drastically cut to meet a certain requirement. Similarly, in Texas, the Yates field has been developed and has been producing under an agreement on the part of the operators; and more recently in Oklahoma City, serious efforts have been made to keep produetion in line with consumption. For the year 1930 we can see nothing in sight except drastic curtailment. This is a matter that I am sure is occupying the attention of all the leaders of the industry.

Jan 1, 1930

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

Discussion Of the paper Of GEORGE K. BURGESS, J. J. CROWE, H. S. RAWDON, and R. G. WALTENBERG, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin NO. 93, September, 1914, pp. 2433 to 2437. ALBERT SAUVEUR, Cambridge, Mass.-The Bureau of Standards has once more rendered a public service. Manufacturers and consumers of steel rails alike should welcome the important results now laid before them by Dr. Burgess and his co-workers. Personally I welcome these results all the more that in the past, as some of the members may remember, I have never failed, when occasion arose, to call the attention of rail manufacturers to the importance of controlling the finishing temperature of their rails. The pioneer metallographic work conducted at the South Works of the Illinois Steel Co. in the early '90s clearly brought out the close relations existing between the manufacture, properties, and finishing temperature of steel rails and I think I may say without fear of being contradicted that the results of this early investigation had considerable influence in drawing the attention of manufacturers to the importance of finishing temperature and of heat treatment in general. The results now before us should be, it seems to me, of great value to rail manufacturers in their efforts to produce a better and, above all, a safer rail. It seems to be demonstrated in this paper that there is no difficulty in installing in rail mills pyrometric outfits, making it possible to record, without interfering in the mill operations, the temperature of the rails as they leave the finishing rolls, or of the ingots as they are withdrawn from the soaking pits, or at any intermediate point in the process of manufacture. The inference necessarily follows that manufacturers should see to it that such pyrometric installations are made, in order that they may actually know, instead of guessing at, the temperature of their rails;, and, for obvious reasons, rail consumers should insist upon such installations. In the rolling of heavy sections especially should care be taken to lower their finishing temperature, seeing that the present tendency is to finish them at higher temperature, whereas, owing to the slower cooling of their central portions, which makes for coarseness of grain, they should, if anything, be finished at a lower temperature than lighter rails.

Jan 4, 1915

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By AIME AIME

MONDAY, Feb. 21, evokes memories of the Silver Corridor at the Waldorf to be recalled and reflected upon for time to come when thoughts drift to the Annual Meeting of 1944. Crowded though it was, on occasion there lurked in the mind's eye a vision of what might have been had the 2886 persons who put in an appearance at one time or another milled around in the lobby of 29 West 39th Street. Some confusion resulted from difficulty in locating meeting rooms, but for the most part everyone found what he wanted. The usual bulletin board of members registered was missing this year and rumor has it that tile Waldorf didn't approve. Registration broke all previous records with many a busy engineer realizing that the program had something to offer that would be of use in his particular job. It might be noted here that "Arpad" co-operated nicely, previewing spring days on Monday, Wednesday, and Thursday; Tuesday was a bit damp.

Jan 1, 1944

By W. A. Backofen, D. Lee, F. S. Jabara

THE empirical character of plasticity analysis insures a continuing need for measurements of the yield surfaces of anisotropic materials. Recently, Wheeler and Ireland (W-I) proposed that an octahedral yield locus could be constructed on the basis of six Knoop hardness indentations. Such simplicity would have obvious appeal, if it led to consistently dependable results. In other recent work, a much more straightforward (and more tedious) method of measurement was used to establish all quadrants of the plane-stress yield loci for two substantially anisotropic titanium alloys.2,3 The same materials have since been reex-amined by the W-I method with results being reported here. A full description of the stress state under a Knoop indentor would be complex. In principle, however, this can be avoided in relating the hardness number to a plane-stress yield locus, by the expedient of superimposing the appropriate hydrostatic component on that state of stress. Six possible orientations of in-dentor on orthogonal (symmetry) planes, along (principal) coordinate directions, are illustrated in Fig. 1(0). Pictured in Fig. l(b) are normal-stress components nominally associated with indentation n: o2(H), directly proportional to the Khn in this case, together with By overlaying a hydrostatic tension, ah, that in general is equal to the stress state around the indentation is reduced to one of plane stress in the x-y plane for which the stress ratio is a The key step in the W-I yield-locus construction is to represent the Khn for any indentor orientation as a vector quantity on the octahedral plane. In the plotting, the vector is given as deviatoric stress components along the principal axes in the ratio , where represents the direction of the minor (width) diagonal and 1 that of the major (length) diagonal. There is no attempt by W-I to justify the 7/1, although it might be supposed that the value originates in the usual ratio of major to minor diagonals in a Knoop indentation of about 7/1. If that were its origin, the link to the deviatoric stress ratio would presumably be made by first taking 7/1 and then turning to the Levy-Mises equation for isotropic material: Interpreted in this way, the W-1 approach seems arbitrary and even contradictory. Yet it would still be favored by two circumstances: the deformation under a Knoop indentor approaches plane strain: when dcw/del =a; and the shape of the locus where plane strain is represented is not overly sensitive either to the exact value of dc,/dcl or to the degree of anisotropy, within a rather wide range of both variables. The second point is illustrated below, after a few additional comments on applying hardness

Jan 1, 1968

By P. Hazebroek, C. S. Mathews, E. E. Allen, H. C. Lefkovits

A rigorous study was made of the behavior of reservoirs composed of horizontal layers, unconnected except at the well and filled with a compressible fluid. The report is presented in two parts. Part I deals with the practical implications of the results obtained; Part 11 contains the mathematical derivation of the solution. The main portion of Part I is concerned with application of the results to reservoirs composed of two layers. Relative rates of depletion of the layers are studied, and it is shown that differential depletion between layers exists in the transient stage of the reservoir, which generally is of an order of magnitude longer than the transient stage in a single-layer reservoir. In the transient stage, the more permeable layer is depleted faster than the less permeable. However, the reservoir approaches a steady-state situation where both layers contribute equally to production. Theoretical build-up curves from such reservoirs are presented, and the influence of a skin effect and flow into casing and tubing are also evaluated. The build-up curves are predicted to have, first, the familiar logarithmic straight-line section and, subsequently, a rising and flattened section. The results found are compared with an extension of an approximate theory, and it is found that this simplified theory is applicable over most of the life of the reservoir. Extensions to reservoirs containing more than two layers are indicated, and examples of the performance and build-up curves for three-layered reservoirs are presented. The theoretical results on build-up curves were applied to field examples of such reservoirs, and satisfactory results were obtained. From the build-up curve, the pemeability-thickness product, the wellbore damage and the static pressure are obtained. However, it apparently is not possible to determine the properties of the individual layers from the combined build-up curve. A large number of reservoirs have been found where the producing formation is composed of two or more layers of differing physical characteristics, such as permeability and porosity, and where also the thicknesses of the layers differ. Since in general a differential depletion should exist between the layers of such reservoirs, it would be advantageous to know the amount of the differential depletion under a given production history. It also would be valuable to know the pressure behavior, because it could be undesirable to produce a reservoir in such a manner that the pressure in one of the layers would have fallen below the bubble point of the oil at a time when another layer might still be virtually undepleted. The determination of static pressures in shut-in wells with slow build-up is another feature of importance in layered reservoirs. If the behavior of the reservoir differs appreciably from the predicted behavior of a single-layer reservoir, the type of analysis for build-up curves suggested for single-layer reservoirs is not applicable. Several authors have treated the problem of finding the pressure and production characteristics of multilayer reservoirs. Horner treated the problem of n layers in an infinite field, the layers being connected only at the well. Tempelaar-Lietz2 has presented an approximate treatment of the characteristics of a bounded reservoir composed of two layers of different permeabilities and equal thicknesses. Homer gave no information on differential depletion between layers, and the treatment of Tempelaar-Lietz was not applicable for prediction of pressure build-up behavior. In addition, it was thought that a more rigorous treatment than the one by Tempelaar-Lietz would be valuable in determining the range of validity of this solution. The present study, therefore, was made of a bounded reservoir composed of two or more layers,