Search Documents

By Niels Hansen

The substructure formed by drawing at room temperature in aluminum (99.5 and 99.998 pct purity) and in recrystallized aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum -oxide was examined by transmission electron microscopy, and the flow stress of the drawn materials was measured by tensile testing at room temperature. A sub-grain structure was present after a reduction in area by drawing of 10 to 20 pct, and the subgrain size was observed to decrease with increasing deformation. The tensile data show that the increase in flow stress (0.2 pct offset) by drawing from 10 to 95 pct depends on the reduction in area, not on the composition of the materials. Dispersion strengthening and subgrain bowzdary strengtlzening contribute to the flow stress, and these strengthening processes have been found to be linearly additive. The flow stress (0) can be related to the subgrain size &) by the Petclz relation = uo + k . t, where go is dependent on the composition of the products and k is approximately the same far all materials. THE microstructure of dispersion-strengthened aluminum aluminum-oxide products consists of small oxide plates distributed in an aluminum matrix. The matrix structure depends on the manufacturing history, and in hot-worked as well as cold-worked products the matrix is divided by subgrain (or dislocation) boundaries. For hot-extruded products it has been shown1 that dispersion strengthening and subgrain boundary strengthening are linearly additive, and the flow stress (0.2 pct offset.) at room temperature has been related to the subgrain size (ts) by a Petch equation,2,3 s = so + k . ts-1/2, where s0, increases with increasing oxide content. For cold-worked products containing subgrains no systematic work has been reported, and it was the aim of the present study to examine the microstructure and the relationship between the flow stress and the subgrain size for such products. The behavior of' aluminum aluminum-oxide products depends on the purity of the aluminum matrix, and aluminum of the matrix purity (99.5 pct) was included in the investigation. The literature contains few data about the behavior of this impure aluminum, and aluminum of a higher purity (99.998 pct) was therefore also examined. As regards the relationship between the flow stress and the subgrain size in cold-worked dispersion-strengthened products, no systematic work has been reported. For aged cold-worked structures containing fine precipitates (Fe-Mo carbide) a Petch relation has been found,4 and it has been shown that the k value NlELS HANSEN is Head, Metallurgy Department, Danish Atomic Energy Commission, Research Establishment Riso, Denmark. Manuscriot submitted January 9, 1969. IMD is approximately the same as in iron, whereas the s0 value is higher owing to the presence of the precipi-tates. Investigations of metals such as tungsten,' ferrous metals,4,6 and molybdenum7 cold drawn or swaged at room temperature have shown that the flow stress can be related to the subgrain size by a Petch relation when ts is taken as the subgrain size perpendicular to the direction of deformation. For aluminum no work has been reported on the relationship between the flow stress and the subgrain size after deformation at room temperature, whereas for aluminum tensile strained at different temperatures in the range -183" to 375°C a Petch relation has been found by taking ts equal to the subgrain size.' In the present study two aluminum materials (99.998 and 99.5 pct) and three aluminum aluminum-oxide products (containing 0.2, 1.0, and 4.7 wt pct oxide) were drawn at room temperature to reductions in area from about 10 to about 95 pct. The structures were studied by transmission electron microscopy, and the flow stress (0.2 pct offset) was measured at room temperature. EXPERIMENTAL Materials. The materials are given in Table I together with the chemical analysis. The three aluminum aluminum-oxide products were manufactured from aluminum powder that had been compacted and Table I. Chemical Analysis of Materials Al203 Fe SI Material wt pct wt pct wt pct 99.998 pct* - 0.0004 0.0012 Aluminum 99.5 pctt - 0.36 0.16 Aluminum AlMD13† 0.2 0.16 0.12 Aluminum- -Oxide AlMD105† 1.0 0.26 0.18 Products SAPISML960s† 4.7 0.22 0.19 *Other impurities: O.0004 pct max each of Cu and Zn (supplier's analysis). †Other impurities: 0.03 pct max Cu. 0.02 pct max each of Mn, Mg, Zn, Ti. Table 11. Mean Diameter of Aluminum-Oxide Particles in Extruded and in Cold--Drawn Aluminum Aluminum-Oxide Products Mean Diam. of A1203-Plates* Material State A AlMD105 Extruded 540 Cold Drawn 97 pct 510 SAP ISML 960 Extruded 770 Cold Drawn 95 pct 820 *The standard deviation of the mean is approx. 5 ±pct.

Jan 1, 1970

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By Jasper L. Stuckey

GEOGRAPHICALLY, North Carolina consists of three divisions, the coastal plain on the east, the piedmont plateau in the center, and the Appalachian mountain region on the west. Geologically, the State may be divided into two main divisions, an eastern or coastal plain region, and a western or piedmont plateau and mountain region. The eastern region is underlain with unconsolidated sands, clays, marls, and shell limestones varying in age from Cretaceous to Recent. The western region is, in general, underlain with gneisses, schists, slates, sheared volcanics, and igneous intrusives of Pre-Cambrian age. In the mountain and upper piedmont portion of the western region are several areas of irregularly metamorphosed sediments of early Paleozoic age. Throughout the piedmont plateau and a part of the mountain portion of the western region, important areas are underlain with igneous intrusives of late Carboniferous age. Along the eastern edge of the piedmont plateau are two narrow belts, trending northeast-southwest, underlain with sediments of upper Triassic age. Although North Carolina contains a

Jan 1, 1947

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

By K. P. Mukherjee, K. P. Gupta, J. Bandyopadhyaya

Even though a lot of work has been done in the past to establish phase equilibrium in the Cu-Si system a re cent investigation casts some doubt about the existence and crystal structure of some of the phases that form in the composition range of 15 to 25 at. pct Si in Cu. The present investigation was carried out using high temperature X-ray diffraction technique along with other standard techniques to study the phases in this composition range. The high temperature 6 phase appears to be tetragonal with parameters a,, = 8.815A, c, = 7.903A, and co/ao = 0.896. The reported bcc E phase exists at room temperature and at least up to 780°C and appears to undergo a transformation near 600°C. The phase appears to be cubic but not of the bcc type. The ? phase appears to undergo a transformation, as has been indicated by earlier investigators, and the low temperature form of .? phase is tetragonal with parameters a, = 7.267A, co = 7.8924, and co/ao = 1.086. THE Cu-Si binary system has been investigated by several investigators1" and several intermediate phases,?,e,?' at lower temperatures and ?,ß,0,e, and ? at higher temperatures, were observed between terminal solid solutions of copper and silicon. Even though the existence of the e phase and the transformation in the ? phase were reported in many early works, in a recent study of this system Nowotny and Bittner6 doubted the existence of the e phase and phase at 550°C. Among the high temperature phases, the 6 phase was reported to have a complex cubic structure with parameter a, = 8.805A.7 Nowotny and Bittner, however, suggested that the structure of the 6 phase might be of CsCl type. In order to check these contradictory reports the present study was taken up to investigate the Cu-Si binary system in the composition range of 17 to 25 at. pct Si. EXPERIMENTAL PROCEDURE Weighed amounts of copper (99.99 pct) and silicon (99.9 pct) were induction melted in recrystallized alumina crucibles under argon gas atmosphere. The alloys containing 17, 18, 20, 21, 21.2, 22, and 24 at. pct Si were annealed in evacuated and sealed quartz capsules at 700°C for 3 days and subsequently water quenched. Other than this annealing, the 21.2 at. pct Si and 24 at. pct Si alloys were annealed at 550°C for 10 days, the 17 at. pct Si alloy was annealed at 750°C for 3 days, and the 22 and 24 at. pct Si alloys were annealed at 780°C for 2 days. All annealing temperatures were controlled to within *l°C. Alloys after quenching were subjected to metallographic and X-ray diffraction investigation. A solution containing 5 g FeC13 + 10 cc HCl + 120 cc H2O diluted with six times its volume with water was used as etching reagent. A 114.6 mm diam Debye Scherrer camera was used for obtaining diffraction patterns. The 17, 21.2, and 24 at. pct Si alloys were subjected to high temperature diffractometry using a Tempress Research High temperature attachment and a GEXRD VI diffractometer. For the 6 phase (17 at. pct Si alloy) powder specimen from a 750°C annealed alloy was reheated to 750°C in the high temperature attachment for 1½ hr before taking a diffraction trace. A 550°C annealed and slowly cooled phase (24 at. pct Si) alloy was first reheated to 550°C. a diffraction trace was made after annealing it for 2 hr, and subsequently it was heated to 716OC and kept at this temperature for 2 hr before taking a diffraction trace. For the e phase (21.2 at. pct Si alloy) a 550°C annealed and slowly cooled specimen was heated first to 425°C and annealed at this temperature for 2 hr before taking a diffraction trace. Subsequently, the specimen temperature was raised to 495", 540°, 603", 635", 682", 720°, and 748°C and homogenized at each temperature for 1 hr before taking diffraction traces. The powder specimen temperature was controlled to within +2oC at each temperature and argon gas, purified by passing it at slow rate through a fused CaC12 column, hot (800°C) copper and titanium chips and finally through a P2O5 column, was used to prevent oxidation of the powder. For all X-ray work copper-radiations at 25 kv, 15 ma (for Debye Scherrer technique), and 40 kv, 20 ma (for diffractometer tech-nique) were used. RESULTS AND DISCUSSION At 700°C the alloys containing 17 to 21 at. pct Si showed two phases while the 21.2 at. pct Si alloy was found to be single phase. The X-ray diffraction patterns of the two-phase alloys were consistent with the phase (ßP-Mn type structure) and the phase (21.2 at. pct Si) patterns. The diffraction patterns of the 17 at. pct Si alloy quenched from 750" and 700°C were identical. According to the accepted Cu-Si phase dia-gram4,5,10 the 17 at. pct Si alloy at 750°C should be in the (k + 6) two-phase region and very close to the -phase boundary. The identical patterns possibly resulted from the decomposition of the 6 phase on

Jan 1, 1970

By Otis W. Freeman

Production of oil in Indiana during 1944 is estimated at approximately 4,950,000 bbl., a decline of 6 per cent from the preceding year. Shortage of labor and material, together with governmental regulations resulting from the war, largely account for the drop in output and limited new developments. Three new pools were discovered in the state during 1944. Two of these, New Harmony, South, and Hovey, West, are in Posey County. Six wells in the New Harmony, South, field produced 66,422 bbl. of oil last year. A third field, Cato, in Pike County, did not market the oil from its discovery well during 1944. Several wells discovered oil in the Henderson field of Jay County along the Ohio state line. An important south extension of the St. Thomas field in Knox County was discovered during the year. Active drilling took place in the Inman, East, and Upton fields, Posey County, both discovered in 1943. Twenty-two wells in Inman, East, produced 151,1gr bbl. in 1944 and 12 in Upton produced 107,052 bbl. Owensville, and especially Owensville, North, in Gibson County, made large gains in production as a result of active drilling. The Dodds Bridge field in Sullivan County continued good production from deep sands reached in 1942. The Griffin continued to be the largest producer among the oil pools of Indiana, accounting for 2,004,180 bbl., over 40 per cent of the state's output. The next largest producing fields are Mt. Vernon and New Harmony, both in Posey County. The largest gas well brought in during 1944 was in the Rockport field, Spencer County, and had an initial output of 2,680,000 cu. ft. per day. The most productive gas fields in Indiana are Rockport, Spencer County, Greensburg, Decatur County, and Unionville, Monroe County. Total production in the state is . hard to estimate, as considerable gas is consumcd in farm homes and for other local uses, and never is reported, but was near 1500 million cubic feet. Some oil from the Trenton field is also used locally and is unreported from pipe-line runs. A total of 606,145 ft. of new hole was drilled in Indiana in 1944. Most of the completions were in Posey and Gibson counties, although wells were drilled in 36 different counties. During the year 331 wells were completed. Of these, 145 found oil in commercial quantities and 28 were gas wells. The initial production of the 145 oil wells was 11,908 bbl. per day. Settled production would be less, of course. The largest wells reported during the year were two on the J. W. Mann farm, in the Mt. Vernon field, with a flush flow of 500 to 800 bbl. each.. Six pools, all small "one well" affairs, were abandoned in 1944; i.e., Fleenor and Patoka in Gibson County, Grafton and Rapture in Posey County, Vaughn in Vandei-bwgh County and Millersburgh, Warrick County.

Jan 1, 1945

By R. P. Laforce, ZJ. R. Low, A. M. Turkalo, D. F. Stein

The interaction of the crlloying eletnenls, nickel and chromium, with the impurity elements, antimony, pIzosphorus, tin, and arsenic, to producse reversible temper brittleness in a series of high-purity steels containing 0.40 wt pct C has been investigated. The alloyed steels contained approximately 3.5 pcl Ni, 1.7 pct Cr, and 0.05 to 0.08 pct of the particular irnpurity to be investigated. Susceptibility to teirlper embrittlement was measured by comparing the notched-bar transition temperature of each steel after quenching from the final temper and after very slow cooling (step cooling;) following the final temper. A plain carbon steel without alloying elements, bu/ ud/h 0.08 pel Sh, does not embrittle when step-cooled through the emzbrittling range of temperatures. The same embrittling treatment, applied to a steel with about the same antinzony content but with nickel and chvonziunz added, causes a 700°C increase in transition temperature. If chromium or nickel is the only alloying element, the increase in transition temperature is only 50%, again with antimony present. A carbon-free iron containing nickel, chromium, and antimony shou~s a 200°C shift in transition temperature for the same thermal treatment. Specific alloy-impurily interactions are also observed for the other impurity elements, phosphorus, tin, and arsenic. Additional investigations involving electron microscopy, trzicrohard-ness tests of vain boundaries, minor additions of zirconiutn and the rare earth and noble metals, nzainly with negative results, are also described. HE particular type of embrittlement investigated is that which is encountered in alloy steels tempered in the temperature range from about 350" to 525'C or slowly cooled through this range of temperatures when tempered above this range. This type of embrittlement is sometimes called reversible temper brittleness to distinguish it from the embrittlement indicated by a minimum in the room-temperature V -notch Charpy energy vs tempering-temperature curve encountered in the range 28 0" to 350°C. Temper brittle-ness seriously restricts the use of many alloy steels since it precludes tempering or use in the embrittling range of temperatures and may significantly raise the ductile-brittle transition temperature of heavy-section forgings and castings tempered above the embrittling range, since such sections cannot be sufficiently rapidly cooled after tempering to avoid embrittlement. The very voluminous literature of temper brittle-ness up to about 1960 has been reviewed by woodfine' and LOW.' Of particular significance to the present investigation was the demonstration by Balajiva, Cook, and worn3 that high-purity Ni-Cr steel does not exhibit temper brittleness and the subsequent detailed and systematic study by Steven and Balajiva~ of the effect of impurity additions on the susceptibility to embrittlement of Ni-Cr steels. Steven and Balajiva showed that, of the impurities which may be found in commercial steels, Sb, As, P, Sn, Mn, and Si could all produce temper brittleness in a high-purity Ni-Cr steel. The principal purpose of the present investigation was to study the effects of particular alloy-impurity combinations on susceptibility to temper embrittlement. The steels used were high-purity 0.30 to 0.40 wt pct C steels containing 3.5 wt pct Ni and 1.7 wt pct Cr, separately or in combination. The susceptibility of these steels was then determined when approximately 500 ppm by weight of antimony, arsenic, phosphorus, or tin were added as an impurity. The melting, casting, and forging practices used in the preparation of the materials investigated are described in Appendix A. Table A-I in this appendix shows the analysis of all steels to be discussed. The steels were produced as 20- or 2-lb heats. The smaller heats were used after it had been demonstrated (see Appendix B) that a small, round, notched test specimen could be used to measure the shift in the ductile-brittle transition temperature caused by temper brittleness with about the same result as that obtained by Charpy testing. HEAT TREATMENT Unless otherwise noted, all steels were tested for embrittlement in the tempered martensitic condition. A typical heat treatment for a 0.40 C, 3.5 Ni, 1.7 Cr steel was: 1 hr at 870"C, in argon, quench into oil at 100"C, quench into liquid nitrogen, temper 1 hr at 625"C, and water-quench. The warm oil quench was used where quench-cracking was encountered; otherwise the initial quench was into room-temperature oil or water. For other compositions austenitizing temperatures were 50°C above Acs with the remainder of the thermal cycle the same. Steels in this condition, with no further heat treatment, are designated as non-embrittled. The above quenching and tempering cycle for the 0.40 pct C steels resulted in as-quenched hardnesses of 48 to 53 RC and as-tempered hardnesses of 24 to 31 Rc except in the case of the plain nickel or plain carbon steels. In these, the as-tempered hardness was as low as 80 to 90 Rg. No attempt was made to adjust the tempering temperature to obtain the same hardness in ali steels since it was felt that a uniform thermal cycle was more important than exactly equivalent hardness values. Pro- the standard quench and temper described above, the standard embrittling treatment was "step-cooling". For this the thermal cycle was: 593"C, 1 hr; furnace-cool to 538"C, hold 15 hr; cool to 524"C, hold 24 hr; cool to 496"C, hold 48 hr; cool to 468'C, hold 72

Jan 1, 1969

By Walter E. Mingramm

The construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquefied air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the difficulty and cost of keeping on hand a large quantity of liquefied air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found

Jan 1, 1909

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

By Albert R. Ledoux

I am indebted to The Kaolin Co. of West Cornwall, Conn., and particularly to its engineer, Mr. M. Wanner, for permission to make public, through the Transactions of the American Institute of Mining Engineers, the interesting results of his experiments, having in view the winning of kaolin from deep deposits without shaft-sinking or removing of the overburden. So far as I am aware, nothing like it has been accomplished heretofore, although it reminds one of the methods successfully employed in Louisiana for the winning of sulphur from deep beds by the sinking of pipes one within another, injecting superheated steam under pressure through one pipe, the heat of the steam liquefying the sulphur and the pressure forcing it up through the other pipe to bins at the surface. The kaolin-deposit at West Cornwall is an alteration in situ— that is, it is not sedimentary. A series of clay-veins, dipping about 50" from the vertical, lie between a foot-wall of' limonite and a hanging-wall of gneiss and hornblende schist. The clay-veins alternate with veins or seams of more or less broken quartz, and unaltered feldspar. The deposit, which occurs at a point about 600 ft. above the Housatonic river, was opened five years ago, and about 5,000 tons of a superior grade of washed kaolin have been extracted from open pits, and sold. It soon became evident that this mode of extracting the product would prove unremunerative, by reason of the dip of the vein and the intercalary strata and lenses of quartz, and a more satisfactory method of working the deposit was sought. It is well understood that, in the preparation of all clays for market, especially residuary kaolin, the most important as well as the most difficult step is the washing of the crude product. The dificulties increaee with the percentage of foreign matter, especially quartz and mica, contained in the product. Hence, a system

Jan 1, 1907

By P. E. Demmler

Phosphorus combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent, grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal Industry' gives the following: Superphosphate of calcium, 60 lb.; granulated copper, 30 1b.; finely powdered coal, 10 1b. Similar formulas are given by Brannt2 and others, and detail variations are covered by patents, such as those of L. A. Jeffs3 and H. A. Webster.4 Among the objections to this method of producing phosphor-copper are the large amounts of raw material and resulting slag to be handled, and the difficulty of getting a satisfactory fusion. S. Skowronski5 found that at 1300' C. (2372' F.) it was impossible to get a good fusion

Jan 1, 1921

By Albert R. Ledoux

I AM indebted to The Kaolin Co. of West Cornwall, Conn., and particularly to its engineer, Mr. M. Wanner, for permission to make public, through the Transactions of the American Institute of Mining Engineers, the interesting results of his experiments, having in view the winning of kaolin from deep deposits without shaft-sinking or removing of the overburden. So far as I am aware, nothing like it has been accomplished heretofore, although it reminds one of the methods successfully employed in Louisiana for the winning of sulphur from deep beds by the sinking of pipes one within another, injecting superheated steam under pressure through one pipe, the heat of the steam liquefying the sulphur and the pressure forcing it up through the other pipe to bins at the surface. The kaolin-deposit at Nest Cornwall is an alteration in situ-that is, it is not sedimentary. A series of clay-veins dipping about 500 from the vertical, lie between a foot-wall of limonite and a hanging-wall of gneiss and hornblende schist. The clay-veins alternate with veins or seams of more or less broken quartz, and unaltered feldspar. The deposit, which occurs at a point about 600 ft. above the Housatonic river, was opened five years ago, and about 5,000 tons of a superior grade of washed kaolin has been extracted from open pits and sold. It soon became evident that this node of extracting the product would prove unremunerative, by reason of the dip of the vein and the intercalary strata and lenses of -quartz, and a more satisfactory method of working the deposit was sought. It is well understood, that, in the preparation of all clays for market, especially residuary kaolin, the most important as well as the most difficult step is the washing of the crude product. The difficulties increase with the percentage of foreign matter, especially quartz and mica, contained in the product, hence a sys-

May 1, 1906

By A. R. Calawa, T. C. Harman, M. Finn, P. Youtz

A study has been made of the growing, annealing, and diffusion parameters in PbSe, Pb1-ySnySe, and Pb1-xSnxTe. Single crystals of these materials have been grown using the Bridgman technique. For all of the above materials the as-grown crystals are p type with high carrier densities. To reduce the carrier concentration and increase the carrier mobility, the samples are annealed either isothermally or by a two-zone method. From isothermal anneals, the liquidus-solidus boundary on the metal-rich side of the stoichiometric composition has been obtained for some alloys of Pb1-xSnxTe and on both the metal- and seleniunz-rich sides for PbSe and alloys of Pbl-ySnySe. In Pbo.935 Sno.065 Se carrier concentrations as low as 5 x1016 Cm-3 and mobilities as high as 44,000 sq cm v-1 sec-1 at 77°K have been obtained. Inter diffusion parameters mere also studied. The ddiffusion experiments mere identical to the isothermal or two-zone annealing experiments except that the samples were removed prior to complete equilibration. The resulting p-n junction depths were determined by sectioning and thermal probing. Inter diffusion coefficients for various temperatures were calculated for both PbSe and Pb0.93Sn0.0,Se. RECENTLY, there has been considerable interest in the PbTe-SnTe and PbSe-SnSe alloys with the rock salt crystal structure. The unusual feature of these systems is the variation of energy gap EG with composition. Several investigations1-3 have shown that EG for the lead chalcogenides decreases as the tin content increases, goes through zero, and then increases again with further increase in tin content. The possibility of obtaining an arbitrary energy gap by selecting the composition is an especially attractive feature of these alloys for applications involving long-wavelength infrared detectors and lasers. In addition, some unusual magneto-optical, galvanomagnetic, and thermomag-netic effects should occur for alloys with low band gaps. If uncompensated low carrier density crystals can be obtained, then a small carrier effective mass, a large dielectric constant, and the resultant high carrier mobility should yield enormous effects at low temperature in a magnetic field. The relative variation of the energy gap with pressure should also be very large for these low gap materials. The primary purpose of this paper is to provide some information concerning the preparation of low carrier concentra- tion, high carrier mobility, and homogeneous single crystals with a predetermined alloy composition. I) DETERMINATION OF ALLOY COMPOSITIONS In all of the work described in this paper, the composition of lead and tin chalcogenides in the alloys was determined by electron microprobe analysis. Separate X-ray spectrometers are used to make simultaneous intensity measurements of the Pb La1 and Sn La1 lines emitted by the sample under excitation by a beam of 25 kev electrons focused to a spot about 2 µm in diam. These intensities are compared to the intensities of the same lines emitted by standards under the same conditions. The standards used are the terminal compounds of each pseudobinary system, i.e., PbTe and SnTe for Pbl-xSnxTe alloys, PbSe and SnSe for Pbl-ySnySe alloys. The composition of the sample is then obtained from theoretical calibration curves which relate the weight fractions of lead and tin in the alloy to the measured ratios of X-ray intensities for the sample and the standards. The lead and tin calibration curves for each alloy system were calculated by using corrections for backscattered electrons,4 ionization,5 and absorption,6 and assuming that the atom fraction of tellurium or selenium in the sample and standards is exactly +. Results obtained by using the microprobe are in good agreement with those obtained by wet chemical analysis. II) CRYSTAL GROWTH FROM THE VAPOR Early work on the vapor growth of PbSe was carried out by Prior.7 He used small chips of Bridgman-grown single crystals as the source material and frequently converted the whole charge of a few grams into one crystal. In the present work, vapor growth occurred using a metal-rich or chalcogenide-rich two-phased alloy powder as the source material. Small, nearly stoichiometric crystals are formed on the walls of the quartz tube. The procedure will now be described in detail. Initially, a 100-g charge containing (metal)o.51(chalco-genide)o 49 proportions or (metal)o.49(chalcogenide)o. 51 proportions of the as-received elements in chunk form are placed in a fused silica ampoule. After the ampoule is loaded, it is evacuated with a diffusion pump and sealed. The sealed ampoule is placed in the center of a vertical resistance furnace. The region containing the ampoule is heated to about 50°C above the liquidus temper-ature for the particular composition used. After about one-half hour at temperature, the elements are reacted and the molten material homogenized. The ampoule is quenched in water. The quenched ingot is crushed to a coarse powder for vapor growth experiments and to a fine powder for the isothermal annealing experiments which are discussed in a later section. Vapor growth experiments were carried out using the powdered, metal-rich or chalcogenide-rich alloys

Jan 1, 1969

By Donald L. Everhart

Beginning in 1906, data has been compiled on the distribution of uranium in phosphate de- posits. Particular emphasis has been placed on uranium in phosphate by a number of geologists and geochemists in the US Geological Survey in research sponsored by the US Atomic Energy Commission (now Nuclear Regulatory Commission) and the US Department of Energy (DOE) during the 30-year period from 1951 to 1981. A comprehensive study of uraniferous phosphate resources the United States and the Free World was completed, under the auspices of DOE, in 1979. Apatite is the main carrier of uranium in phosphate. Uranium generally replaces calcium in the mineral lattice. In marine phosphorite throughout the world, the uranium content is characteristically in the range of 0.005 to 0.02% by weight. Phosphorite takes in uranium by structural substitution in apatite or other mineral phases, by absorption, or by the formation of independent mineral phases. Apatite derived from the interaction of ground water, guano and limestone is typically relatively low in uranium content-in the 0.001 to 0.005% range. In primary accessory apatite of igneous rocks, as well as magmatic and metasomatic apatite segregations of alkalic rocks and carbonatite, uranium content is generally between 0.001 and 0.01%. In all these phosphate deposit types, secondary enrichment of uranium through

Jan 1, 1983

By Enrique Touceda

The question as to the proper amount of total carbon that the malleable founder would prefer to have in pig iron for use in the production of air-furnace, white iron castings, must be considered from different angles, that is, whether it is desirable or advantageous from an economic standpoint to use some kind of low-carbon scrap on his mixture, or make use of pig and sprue only. Whereas silicon is the acknowledged scrap carrier in the case of cupola gray iron castings, carbon performs this role for the most part in malleable iron practice, irrespective of the character of furnace used for the production of the white iron castings. In this particular, the advantage lies with the maker of gray iron castings in that the silicon content in pig iron through a regulation of furnace temperature is under very easy control by the blast-furnace manager, whereas he has little or no control over the resultant percentage of carbon, as this is dependent on the quantity of coke in the hearth, and hearth temperature, coupled with the amount of hearth slag and its particular composition. As perhaps more than 95 per cent. of white iron castings are made in air furnaces the following statements are intended to cover that situation particularly: In the malleable process the composition of the hard iron castings (that is determined upon as best suited for the work in hand) is the one factor that must control the composition of the mixture to be used; because if the elements are not between certain definite limits individually and collectively the annealed or finished product will be unsoitable, due, perhaps, to lack of sufficient strength or because it is too hard, to machine easily. The annealed product can be divided into two classes, one of which greatly predominates, that is, by far the largest tonnage is used for machine parts where high strength and ductility are essential requisites, while a far smaller amount, light in weight and thin in section, is used for other manufactured products in which castings of any reasonable degree of strength and ductility have proved satisfactory.

Jan 1, 1927

By H. R. Steacy, A. H. Lang

Growth of general interest in uranium during the last ten years has been unparalleled in mining history, outranking the popular gold rushes and mining booms of bygone years. This is not surprising, considering the spectacular advances in nuclear research and the fact that a small amount of uranium can provide great quantities of energy for peaceful purposes. There are, however, a number of misconceptions and exaggerations regarding uranium. Many novices have highly exaggerated ideas of the ease of finding workable deposits, as opposed to mere occurrences, and reports of insignificant discoveries are sometimes given much publicity. Beginning about ten years ago mining for uranium has assumed a major place in Canadian and U. S. mineral industries. Uranium is now high on the list of metals produced in Canada. The gross value of uranium production in Canada in 1958, when additional plants now under construction are operating, will probably exceed 180 million dollars.

Jun 1, 1956

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By E. Cortese

PHOSPHATE occurs in many places in Egypt,. in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the cancel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following, that track, after, having crossed the watershed, underlain by rocks like granite, serpentine, porphyry and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at' Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Auressensis Coq. sp.- R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismäely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconformably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 2, 1918

It is probable that the first commercial production of coal in Ohio was for the supply of Wheeling, before mines were opened at that place. This coal came from Pipe Creek in Belmont County,l where the seam was exposed a short distance above the river. This movement could not have lasted more than a few years, because coal was being mined at Wheeling in 1818, and probably before that.2 Mining began in Tuscarawas County in 1810 and in Perry County in 1816, and has been followed steadily since then. In the eighteen twenties the Pomeroy field in Meigs County, Jackson County, and the northern Ohio field in Summit County commenced production. All of the early data available are given in Table 57. No early official reports were made, but after 1859 the Secretary of State published statistics of production, admittedly inaccurate, by counties, and under various officials these have been continued to the present day. Ohio has never published statistics about coal in smaller units than the county; no reports of individual properties have ever been collected. The period from 1800 to 1885 includes the opening of practically all of the coal fields of the state, although those of eastern Ohio were not large producers at its end. During this time the use of raw block coal in blast furnaces had begun and ended, and at the end, coke was nearly the universal fuel for this purpose. Much of the coal traffic on the Ohio River and its main tributaries originated in the necessity of a fuel supply for Cincinnati and other down-river cities. This traffic started in 1794, and few records of it are available until many years later; in 1846 records of the movement to Cincinnati began and have been maintained with increasing thoroughness, and represent one of the most complete records of such a traffic extant anywhere. As these data show the originating fields of most of the coals used there, the available figures to 1885 have been collected in Table 16.

Jan 1, 1942