Search Documents

By Klaus Schwerdtfeger

In order to test the performance of ZrO, (CaO) and Tho,(Yz03) electrolytes in the electrochemical determination of oxygen activities in liquid metals at steel-rrzakitng temperatures , electromotive force measurements have been made with the following cells: The oxygen-- activities are calculated from the electmrnotive forces for the investigated systems. The standard free energy of- formation of MnO and the activity of manganese in Fe-Mn melts are derived. Indications are that the Zr 0z(Ca0) electrolyte exhibits little electronic conductivity at oxygen pressures as low as 10'a atnz at 1600°C; however, the partial electronic conductivity may become noticeable at lower oxygen activities. The Tho,(Yz03) electrolyte is found to be an ionic conductor at the oxygen pressure as low as that for the Mn + MnO equilibrium, but exhibits partial electronic conductivity at oxygen pressures higher than 10"1 atm (1500°C). fi. better control of oxidation and deoxidation reactions in steelmaking may be facilitated if the oxygen activity in the steel is known during various stages of the process. In the present work oxygen activities have been measured in liquid iron, manganese, and iron alloys with galvanic cells using ZrOz(CaO) and s solid electrolytes with the object of establishing the range of oxygen pressure in which these materials can be used as electrolytes at steelmaking temperatures. Calcia-stabilized zirconia and Tho2-Y203 solid solutions are oxygen ion conductors. Such electrolytes were first used by Kiukkola and Wagner1 and Peters and ~ann' in galvanic cells for the determination of thermodynamicquantities of oxide systems in the temperature range 700" to 1200°C. At these moderate temperatures calcia-stabilized zirconia has been found to exhibit predominantly ionic conductivity at oxygen pressures as low as those for the Cr + Crz03 equilibrium,394 but at lower oxygen pressures elec- tronic contribution to conductivity becomes significants4 The Th02-Y203 solid solutions are ionic conductors at oxygen pressures lower than those applicable to zirconia base electrolytes.5'6 At high oxygen pressures Thoz base electrolytes exhibit significant p-type semiconduction. At the time the present experiments were carried out several papers1'-* were published on the electrochemical determination of oxygen activities in liquid iron using the ZrOz(CaO) electrolyte. The results of different authors do not agree well. For instance, according to Fischer and ~ckermann" stabilized zirconia can be used to measure oxygen contents in liquid iron larger than 0.02 wt pct, but according to Baker and west1' ZrOz(CaO) cannot be used for the determination of oxygen content in liquid iron because of high electronic contribution to the conductivity. Fig. 1 is a schematic diagram of the apparatus used. About 500 g of liquid metal is contained in a crucible into which a stabilized zirconia or Th02(Y203) tube is immersed. A platinum contact wire is pressed (with a spring mechanism) against the inside bottom wall of the electrolyte tube. The tube is flushed continuously with a stream of air, CO-CO, (or Hz-C02) (at 0.96 atm and at a rate of about 300 cu cm per min), via an alumina tube inserted inside the electrolyte tube. This alumina tube also contains the Pt-Pt/10 pct Rh thermocouple. A capillary alumina tube shielding the other contact wire is immersed in the melt. The molybdenum contact wires were used mostly; in some cases platinum wire was employed. Molybdenum has the advantage that it dissolves more slowly in the melt than platinum. The whole cell was contained in the alumina reaction tube of a resistance furnace with molybdenum winding. The reaction tube was closed gas tight at both ends and flushed continuously with argon. Because of the poor thermal shock resistance of the electrolyte tubes the cell had to be assembled in the cold furnace. The electrolyte tube and alumina sheath

Jan 1, 1968

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series,1 for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship [p] to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distribution line is w = Cxm [I] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By P. G. Shewman, T. L. Wilson

Using published surface-diffusion (D,) data and published sintering equations, it is shouln that surface difusion should dominate the neck-growth stage of intering for all materials in which D, has been measured (six metals and A1as). Also, grain boundary diffusion can be expected to contribute appreciably to shrinkage and possibly to neck growth below some critical temperature of the order of 70 pct 01- the absolute melting temperatuve. In view of the widespread conclusion in previous sintering work that volume diffusion dowzinates neck gvowth, experiments were conducted using spherical copper powders to test this conclusion. Scaling studies on neck growth at 950°and 1020°C clearly demonstrated that suyface diffusion dorninates. Kinetic studies on shrinkage gave more equivocal results that indicated an increasing role of' grain boundary transport at lower temperatures. Five diarszeters from 100 to 300 u were used in the scaling sludy and a temperature range of -650' 10 950 C was covered in the shrinkage studies. All experiments were conducted in dvy hydrogen. In 1949, Kuczynski published his now classic paper on the determination of the transport mechanism in sintering from the time laws of neck growth. In the interim, these laws have been applied to many systems and slightly modified by several authors. Essentially all these authors concluded that, for crystal- line materials, the dominant transport mechanism in neck growth is volume diffusion. This stems from the observation that the neck radius increases about as t"5 and that the activation energy approximates that for lattice diffusion. A related but independent series of studies stems from Mullins' rigorous analysis of the growth of the groove formed where a grain boundary meets a free surface." xperimental work stemming from this analysis has shown that for each crystalline material studied (Au, Ag, Cu, Ni, Fe, Pt, Al2O3) surface diffusion was clearly the dominant transport mechanism for groove widths up to the order 10 to 20 p. The ratio of the quantity of material being carried by lattice diffusion to that carried by surface diffusion increases linearly with the groove width, so surface diffusion is dominant for all widths under 10 to 20 u. The analysis of the relative contributions of surface and volume diffusion to grain boundary grooving, and to neck growth in sintering, shows that they are quite similar. Thus, using the available surface-diffusion data and the approximate equations of Kuczynski, or the more rigorous recent equations of Nichols and Mullins, 3 it can be shown that the small necks between particles must grow almost entirely by surface diffusion. The purpose of this study was to re-examine the basis for the conclusion that the neck-growth stage of sintering proceeds by volume diffusion. Using spherical copper powders, of several different diameters, precise experimental measurements were made of both neck growth and shrinkage. Application of Herring's scaling laws to the neck-growth data clearly indicated that neck growth occurred by surface transport, even though the neck radius increased as or Using the recent analysis of Mullins and Nichols as well as published data on surface diffusion, it is shown that the observed time law, as well as actual rate of neck growth, can be satisfactorily explained by a surface-diffusion mechanism.

Jan 1, 1967

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per 100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series, for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship p to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distributi0n line is [w = Cx" [I]] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By Lewis Reeve

As part of a program of investigation of the properties of electric arc welds carried out in the laboratories of the A. 0. Smith Corporation, considerable work has been done on the determination of the oxygen, nitrogen and hydrogen content of different types of weld metal, employing for this purpose the so-called "vacuum fusion method." It is the purpose of this paper to describe certain improvements that have been introduced in this method of determining the gas content of metals, with particular references to the steel specimens examined in this investigation. The method and apparatus used at the beginning of the investigation were essentially those of the Bureau of Standards as described by Vacher and Jordan.' Later a number of changes were introduced which resulted in more rapid evacuation of the graphite crucibles employed and which enabled larger volumes of gas to be dealt with than could be handled conveniently in the Bureau of Standards equipment. In addition, the analyzing of the gases evolved from a melt in the same apparatus as collected was abandoned in favor of analysis outside the equipment using standard methods of gas analysis. The time required for gas analysis in the apparatus itself, as described by the Bureau of Standards, was found to be considerable, and during this time the rest of the equipment was tied up, preventing its use for the analysis of further steel samples. As a result of the modifications introduced, the time required for the analysis of a steel sample for gas content was reduced from about 8 hours to less than 3 hours. Subsequently, the whole procedure of melting the sample and collecting the gases evolved was modified so as to enable a distinction to be drawn between the easily reducible oxides such as iron oxide and the more stable oxides such as silica and alumina. At the same time evidence was obtained indicating the probable existence in the steels of other nitrides than those of iron alone and making possible their quantitative etermination.

Jan 1, 1934

By T. A. Rickard

T HE life and career of Daniel Cowan Jackling constitute a distinctive part of a passing era, marked by the intensive exploration and exploitation of the mineral resources of the western regions of the United States. In the development of his abilities and in the use of his opportunities, he typifies the initiative, the energy, and the skill of a modern captain .of industry. Daniel C. Jackling was born at Hudson, Mo., on Aug. 1.4, 1869. He was the only child of Daniel Jackling, born in England of English parents, and Lydia Jane (Dunn) Jackling, born in the United States, but of Scottish ancestry. His father died a few months after he was born, and he lost his mother less than two years later. The orphan boy was adopted by his aunt. He went to school as soon as he was old enough to walk the two miles, and back, alone. As opportunity offered, he went

Jan 1, 1937

By Ernest R. Dickie

BRIEFLY, the ore body of the Bagdad Copper Corp., Bagdad, Ariz., is a monzonite porphyry carrying copper values fairly evenly distributed from the surface down through the primary zone. Tabular in shape, the ore body extends over several hundred acres. The oxidized zone averages about 60 ft thick and assays about 0.50 per cent copper. Under this is the chalcocite zone, or the zone of secondary enrichment, which averages about 100 ft in thickness and assays about 1.4 per cent copper. Under this zone lies the primary zone which extends in places to a known depth of about 150 ft and averages in grade about 0.60 per cent copper. Several years ago the block-caving method of extracting the ore from the chalcocite zone was installed. Then it was necessary to draw only about 250 to 300 tons per day, the capacity of the old milling plant. Early in 1943 the new 2500-ton concentrator was put into production. Drawing ore from the developed stopes in sufficient tonnage to furnish the mill at capacity proved unsuccessful in more ways than one. First, drawing the ore at an accelerated rate caused a large amount of dilution, there-by lowering the grade, and also caused funneling through to the surface. The surface material was detrimental to milling metallurgy and development of these stopes was costly per ton of ore extracted. The grade of ore decreased. making it impossible to maintain a mill head of over 0.9 per cent copper. The

Jan 1, 1947

E. P. Pfleider, University of Minnesota I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. R. H. Merrill, U. S. Bureau of Mines, Denver Federal Center The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability. G. A. Leonards, Purdue University I was interested in Mr. Lane's observations concerning the correspondence between rate of slide movement with rise of reservoir. Perhaps the most interesting feature is that the rate of movement at the time the rock slope failed was less than the rate at an earlier time when it did not fail. This is difficult to explain from current slope stability theory. K. S. Lane, U. S. Army Corps of Engineers I believe that reduced rate of movement is the result of the progressive type of failure, such as described by Patton and Deere. which occurs along the sliding surfaces. It is difficult to analytically define the progressive failure condition for inclusion in slope stability conditions, but its existence should be recognized in design. We should also realize that many apparently stable slopes undoubtedly contain overstressed regions. To design a slope with no overstressed region would be uneconomical and conservative. D. H. Deere I would pose the question-"What is the meaning of a factor of safety of one?" We were involved in the design of a large, irregularly shaped, underground cavity with an unsupported span of several hundreds of feet. Tests on rock specimens indicated a strength of 1300 lb per sq in. The RQD would have been between 90 to 100 percent indicating excellent structural continuity. In-situ stress determinations indicated an approximately hydrostatic state of stress at a level of 1400 lb per sq in. Calculation of stress concentrations at the walls indicated that the stresses there would be about 3000 to 4000 lb per sq in. Admittedly the rock is in a confined condition everywhere except at the very skin of the wall and the rock walls would thus on the average be somewhat stronger. Allowing for the effect of restraint the factor of safety was found to be less than 0.5 over a region several feet into the wall. Construction was started, using rockbolts only to support the walls. Failure around the immediate skin occurred after each

Jan 1, 1967

By M. E. Straumanis, J. -P. Krumme

In basic ([KOH + KCl] with a total polarity of 2) or acidic (2N H2SO4) electrolytes and at anodic current densities of more thun 2 to 4 ma per sq cnz, n-type GaAs single crystals of lozo resistivity preferentially dissol~je forming etch tunnels with triangular or civc~ilay cross sections and of a width between 0.5 arid 5 p. These etch tunnels are oriented along any one of the four possible (111) directions of GaAs. However, their growth occurs only in one direction of a given (111) whick apparently is determined by the atomic sequence Ga —As (and not the rezlerse) in respect to an individual valence bridge in the crystal. It is concluded from comparison with the cubic lattice structure of GaAs that the etch tunnels represent macroscopic evidence for the tetrahedral bonds and their polar properties. If the anodic current density is increased the tunnel fomation results in the development of a fibrous surface layer consisting of GaAs. The latter separates frorn the substrate (in an anodic s~irface disintegration process) by the growth pressure of an As,0, filnz forming in the interior of the fibrous layer, 100 to 200 µ under the surface, at more than about 50 ma per sq cni. The fibrous GaAs film has the same crystallographic orientation as the substvate and represents a skeleton of the original crystal. Since the etch-tunnel density in a separated GaAs layer is about 108 c?n-', and the etch tunnels develop only along (111) in a given polar direction, it is assurraed tlmt the dislocations have no influence on the growth of these tunnels. ElECTROLYTIC treatment of smooth surfaces of poly- and single-crystalline GaAs at high anodic current densities causes the formation of porous surface layers.' This phenomenon suggests comparison with effects being observed with magnesium,' indium,, gallium,4 and aluminum5 and known as "anodic disintegration". The purpose of the present paper is to explore and to explain the reasons for the formation of such surface layers on GaAs and, in particular, to investigate the influence of the lattice polarity of this III-V compound semiconductor in the (111) direction on the anodic dissolution behavior. GaAs SINGLE CRYSTALS For the experiments described below GaAs single crystals from the Monsanto Co., St. Louis, Mo., were used. Their impurity levels were below 1 ppm and their dopant levels between 1 and 100 ppm. They were grown in (111) using the Czochralski or the gradient-freeze technique. The crystals had n-type conductivity and electric resistivities between 1 and 5 ohm-cm. EXPERIMENTAL The GaAs single-crystal rods were cut perpendicularly to (111) into wafers of about 1 mm thickness using a wire-blade crystal slicer and an aqueous slurry of Sic or a diamond saw. The orientation of the faces of these wafers were checked by Laue back-reflection patterns. If there was a deviation from (111) the faces were abraded under a certain angle using grinding paper and distilled water. The damaged surface layer was removed from each crystal by chemical etching with a mixture of 1HF:1HNO3: 1H20 or 2HF:1HNO3:2HAc (glacial). {110) faces were obtained by mechanical cleavage, producing surfaces which did not require a further treatment. The GaAs wafers were mounted using "alligator" clamps instead of soldered electrical contacts.' Only the bare crystal surfaces were dipped into the electrolyte. The clamps were coated with insulating wax to prevent any contact with the electrolyte. The experiments were carried out in aqueous 2 N H2so4,' or in an aqueous solution of KOH and KCl1 (1 mole KOH + 1 mole KCl in 1000 cu cm solution). Anodic current densities up to several hundred ma per sq cm were applied for periods between 30 sec and 2 hr. For the purpose of investigating the initial steps of disintegration the anodic current density applied never exceeded 20 ma per sq cm. The films which partially separated from the anodic surfaces under high-field conditions were treated with KOH to further their detachment by dissolving the As2O3 formed. The washed and dried films were pasted to strips of filter paper, and Laue pictures were made. The back-reflection patterns obtained were compared with those of the original anode surface before and after anodic dissolution. Furthermore, space reciprocal lattices7 were constructed from asymmetric rotation crystal patternsa which permitted the determination of the crystallographic orientation of the detached films of the corrugated anodic surfaces. The disintegration products were identified from assymmetric powder patterns.8 The polarity of the {111) faces was determined by chemical etching with mixtures of 1HF:1H2O2(30 pct): 2H2O or 1HNO3:2H2O. Different patterns on each of two inverse (111) sides appeared.'-l8 The correlation of these patterns to the Ga{111) or the As(111) side has already been established by the use of light figures,18-20 by X-ray diffraction near the absorption edges of gallium and arsenic,'lmZ4 and by LEED measurements.25 The geometric structure of these surfaces and the interior of the anodically attacked crystals were observed and photographed with a high-power microscope using oil immersion objectives up to magnification of X1720.

Jan 1, 1968

By R. P. Smith

The carbon content of a number of alloys ranging (before carburitation) from purified iron to purified cobalt was determined for fixed activities of carbon by equilibration with each of six CO-CO2 atmosphere at 1000°C. At fixed carbon activity, the carbon content decreases continuously with increasing cobalt content. For concentrations of 0 to 50 at. pct Co the results can be expressed by a linear interaction equation of the type In y2 = 7.76n2/(n1+n3)+ 2.30 n3/(n1+n3) where y2 is the activity coefficient of carbon (standard state such that y2— 1 as n2 — 0 in the Fe-C binary) and n1, n2, and n3 are the number of atoms of iron, carbon, and cobalt per unit weight of alloy. The results are also given in terms of the a functions. In the same concentration range, the results are in accord with the regular solution theory of Alcock and Richardson. THE carbon content of Fe-Si, Fe-Mn, and Fe-Ni alloys at fixed activities of carbon has been reported previously.'-, The present work extends R. P. SMITH, Member AIME, is Research Chemist, E. C. Bain Laboratory for Fundamental Research, United States Steel Corp., Research Center, Monroeville, Pa. these measurements to a series of Fe-Co alloys. These alloys, like the Fe-Ni alloys, are fcc ("aus-tenitic") over the entire range of composition at 1000°C. EXPERIMENTAL PROCEDURE The alloys were made from electrolytic cobalt and Plast-Iron in a small vacuum-melting furnace. A small amount of graphite was added to each melt to keep the oxygen content low. The ingots were analyzed for iron and carbon: the amount of cobalt was obtained by difference. Analysis of the top and bottom of the ingots indicated that they were uniform in alloy content. Except for the pure cobalt the ingots were hot-rolled to approximately 0.15 cm thickness, cleaned by sandblasting, then cold-rolled to about 0.045 cm. We were not successful in cold rolling the pure cobalt; therefore it was hot-rolled to the final thickness. The last traces of surface oxide were removed by acid pickel, then the samples were treated in a hydrogen-2 pct water vapor mixture at 1100°C to remove carbon and most of the oxygen. The carburizing procedure was similar to that previously described.1,2,4 The alloys in the form of strips about 1.7 cm wide, 7.5 cm long, and 0.04 cm thick, together with a similar specimen of purified iron, were equilibrated with each of six CO-CO2 mixtures of fixed composition, then quenched in the

Jan 1, 1965

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

By Sidney Powers

INTRODUCTION THIS paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Fundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Mines, Mines Branch, Ottawa,1 all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of -Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 min. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grains per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 2, 1916

By Edward Jeffrey

THE use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years-the middle of the 17th to the middle of the 18th century-there was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate.

Jan 1, 1925

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

By AIME AIME

MORTIMER ELWYN COOLEY, dean of the College of Engineering and Architecture of the University of Michigan, has been elected president of the American Engineering Council of the Federated American Engineering Societies. This was announced at a meeting of the Executive Board of the Council held at the Cosmos Club in Washington on Sept. 30. Dean Cooley assumes office at once. The new head of organized engineering is a past president of the American Society of Mechanical Engineers and has a long record of distinguished service in education, under the government and in private capacities. He was born in Canandaigua, N. Y., March 28, 1855, and was graduated from the United States Naval Academy in 1878. With his classmate, Dr. Ira N. Hollis, he was ordered to the U.S.S. "Quinnebaug," then fitting out at the Norfolk Navy Yard preparatory to a cruise in the Mediterranean.

Jan 1, 1921

By Everette Lee DeGolyer

FIFTEEN thousand barrels of oil daily, the production of the United States 75 years ago, amounted to more than 90 per cent of world supply. Russia and Romania, neither of which produced as much as one thousand barrels daily, were the only other suppliers in substantial quantity. The adolescent oil industry of the United States, a dozen years old in 1871, was still confined to the Appalachian region. Wells were drilled by cable tools; many of them were "kicked down" by manpower with a spring pole; and depths were measured in hundreds rather than thousands of feet-a 1000-foot well was a deep well. Casing was an innovation, come into general use only a few years previously and still so new as to be subject to bitter patent litigation. Crude oil was packaged in wooden barrels and shipped by flat boat and barge on the creeks and rivers and by railroad. Such pipe lines as existed were only a few miles long. There were many refineries. Pittsburgh, Cleveland and the Atlantic seaboard were refining centers. Refineries were very small, however, and their operations consisted essentially in simple fractionation by distillation and treating for quality. The products in demand were burning oil or kerosene and lubricating oils. Oil was not yet used as fuel and gasoline was a nuisance to the refiner.

Jan 1, 1947

By Frank Firmstone

In April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Figs. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised together, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places.