Search Documents

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920

By Milton H. Fies

EARLY in 1945 the laboratories of the Southern Research Institute will begin active research investigations on behalf of industrial clients. This achievement has come after four years of planning by a group of Alabama businessmen, and is in partialanswer to an urgent need in the South. Those who conceived the Institute have long realized that a marked relationship exists between scientific research and the economic well-being of the several regions of the country. Clearly, technological research, generally absent in the South, is the medium through which are created new finished goods industries, and the increase of technological research is perhaps the most important long-range project in the South.

Jan 1, 1945

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

Duval Corporation, the owners of the Sierrita, Esperanza, and Mineral Park copper operations in Arizona, first acquired the mineral rights to their Battle Mountain, Lander County, Nevada, property in 1962. Development of the mine commenced in mid - 1965, and the copper operation began at the end of 1968. The ore, a mixture of chalcocite and chalcopyrite, was milled and floated at a rate of 3, 175 mtpd (3,500 stpd). Because of low copper grade and price, the plant was shut down after about ten years of operation. Attention was then turned to an adjacent low-grade precious metal ore body which contained 2.74 g Au and 3.4 g Ag per mt (0.08 oz Au and 0.10 oz Ag) and minor amounts of copper. Test work revealed recovery by Carbon-In- Pulp treatment would amount to approximately 2.8 mt (90,000 oz) each of gold and silver per year. A rapid engineering and construction schedule resulted in the world's largest, as of late 1980, Carbon-In- Pulp plant being put on-stream in January 1979, with a capacity of 2.720 mtpd (3,000 stpd). Fortunately, the original crushing and grinding plant with all its infra structure was available, and the only modification needed was the addition of a gravity circuit to remove coarse free gold ahead of Carbon- In-Pulp treatment. One of the four primary 500 mm (20 in.) cyclone underflows in the primary ball mill circuit is directed to a secondary ball mill where its product is again cycloned. The cyclone underflow is screened at 3,360 microns (6 mesh) with the undersize being treated on two Pan American 1.07 m by 2. 14 m (42 in. by 84 in.) jigs. Hutch product is further concentrated on two Wilfley tables, a magnetic separator, and on a third Wilfley table where approximately 930 g (30 oz) of gold are recovered each day for amalgamation, retorting, and smelting. Returning to the grinding circuit, the final cyclone overflow is sent to the original plant tailings thickener to obtain proper pulp density for Carbon-In-Pulp treatment. Thickener underflow, at about 40% solids, is then conditioned with air and lime in a series of two 8.5 m by 9.75 m (28 ft by 32 ft) 15O cone bottom Pachucas for oxidation of pyrrhotite. The pulp is then split into two streams for cyanidation for 48 hours in two lines of eight Pachucas of the same size. Pulp is transferred from tank to tank by auxiliary air lifts. Cyanided pulp is then sent to a series of six C. I. P. mechanically agitated tanks with one hour retention in each tank. Originally these

Jan 1, 1981

By Albert J. Phillips

As early as 1824, Haidinger' described crystals of native copper that were, according to Dana,2 " probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,

By J. A. Woolf, E. S. Leaver

The presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. Part I.—Copper in Cyanidation The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results. Azurite, bornite, chalcocite, cuprite, malachite and finely divided metallic copper are readily and completely soluble under the usual conditions for cyanidation. Enargite and tetrahedrite are sufficiently soluble to cause an excessive loss of cyanide, and they also cause fouling of solutions with arsenic and antimony. Precious-metal ores containing small percentages of chalcopyrite or chrysocolla may give satisfactory returns with the usual cyanidation.

Jan 1, 1930

By W. B. Heroy

ONLY through the mineral fuels can large amounts of energy be transported to great dlstances and stored for long periods for future use. Coal has the advantages over oil of greater safety of handling and smaller losses in storage. But oil is, in the present stage of technical advancement, the more economical source of liquid fuel for internal-combustion motors. No method for direct use of coal in such motors has been developed that can compete with petroleum products. The automoblle engine and the airplane motor are designed to make the most effective use of gasoline.

Jan 1, 1944

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By William Glenn

In their account of chromium, Roscoe and Schorlemmer (Treatise on Chemistry, London, 1879) state that "In 1762 Lehmann, in a letter to Buffon, de nova minerœ plumbi specie crystalline rubra, described a new mineral from Siberia, now termed crocoisite." In 1786 Lehmann analyzed it (Nicholson's Jour., Dee., 1798) and found that it contained chiefly lead, and that the " mineralizers " were arsenic and sulphur. It was next examined in 1189 by Macquart and Vauquelin, who stated that it contained an intimate mixture of iron, alumina, and lead peroxide. The account of their work was published over the name of Macquart. Vauquelin (Louis-Nicolas) was a Norman peasant, who had studied in the village school, and at the age of fourteen was a laboratory-boy in a pharmacy at Rouen. Later, he found his way to Paris, and in 1789 was assistant to Fourcroy, a pharmacist and a teacher of note. It was here that he met Macquart, with whom he did the work on Siberian red lead, and at this time his friend Cheradame taught him his Latin.

Jan 1, 1896

By ROBERT B. COONS

SELECTIVE SERVICE must meet three important demands for man power: (1) Activities concerned with production of war goods. (2) The armed forces. (3) Civilian activities and institutions the continuance of which are essential to maintaining the structure of our American democracy. In the above enumeration of demands I have placed everything, including most of our most prized possessions and activities, after the demand for men for war production and the armed forces. To establish an order between the latter two is difficult. For the time being, at least, the Selective Service policy is to make sure that we avoid the risk of "too little and too late." No soldier, sailor, or marine should be sent from these shores to risk his life without the assurance of having a gun, clothes, food, and medical supplies. Therefore, the premium is now being placed on man power for war production and in our process of selection no stone is left unturned to see that our agencies are fully informed of the needs of war production. Our procedures set up recourses for employers of war-production man power so that their activities need not be disrupted, at least not until they have had time to train replacements.

Jan 1, 1942

By AIME AIME

MINERALS and mineral resources are recognized as one of the things that nations are prone to quarrel about. The territory that was arbitrarily incorporated into the Polish Republic after the World War produces a variety of essential minerals on a substantial scale. The accompanying table has been compiled to give some idea of the relative importance of this production. Poland, before the recent war started, had an area of 150,000 sq.mi., just a little larger than the State of Montana. Its population was 32,000,000, equal to that of New York, New Jersey, Pennsylvania, Connecticut, and Massachusetts. Though not a highly industrialized country it nevertheless has important mines, steel plants, petroleum refineries, and sundry metal-fabricating manufactories. Coal, petroleum, iron and steel, zinc, lead, pyrite, potash, and salt are produced in excess of the country's domestic consumption. It has no appreciable production of copper, chromium, tungsten, nickel, tin, mercury, manganese, aluminum, magnesite, fluorspar, or graphite.

Jan 1, 1939

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By R. D. Pehlke, J. V. Gluck

A study was made of the effect of small additions of metallic solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450o to 650°C. The experimental measurements were made in a multielectrode galvanic cell using. a fused LiCl-KCl electrolyte. The activity of zinc in binary solution exhibited a strong positive deviation from Raoult's law and obeyed Henry 's law to at least 0.050 mole fraction. The ternary addition of lead, gallium, or indium increased the activity of zinc. Cadmium or tin additions slightly decreased the zinc activity. Copper, mercury, silver, or antimony caused moderate decreases, while gold strongly decreased the zinc activity. The results are expressed in terms of Wagner's interaction parameter ejZn and a second-order cross-interaction parameter. The interactions for copper, gold, silver, and antimony showed a linear dependence with reciprocal absolute temperature, while the other interactions were essentially independent of temperature over the experimental range. Since tin and antimony decreased the zinc activity, the hypothesis of a purely periodic variation with atomic number was rejected. A semiquantitative explanation was possible with a free-electron model when relative electronegativities were used to express changes in the electron/atom ratio caused by the solute addition. Random solution and quasi-chemical models correctly predicted the majority of the interactions for which binary data were available to apply them. A knowledge of the thermodynamic interactions in liquid (and solid) metallic solutions is of considerable theoretical and experimental interest in the formulation of quantitative thermodynamic relations for metallurgical processes. The approaches to defining the interactions may be either phenomenological (i.e., "What mathematical function adequately describes observed behavior and permits extrapolation to new situations?") or theoretical, such as a specific model

Jan 1, 1968

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Persifor Frazer

The mines which I am about to describe are all situated in the northern part of the States of Nuevo Leon and Coahuila, Mexico, between the twenty-sixth and twenty-seventh degrees of latitude. They might be grouped, orographically, into four classes: 1. Those in the Sierra de la Ygnana chain; 2. Those in the Sierra de Gomez chain; 3. Those in the Cerro Mercado; 4. Those in the Sierra de San Marcos chain. (See large map.) The first two of these may be further arranged in one geographical district, to which the name, "the Villaldatna. district," may be applied, and the last may be ascribed to the geographical district of " Monclova." Geologically described, the country rock, in which four of the six mines occnr, is a limestone, concerning which a few words will be said further on, to wit.: The Arroyo (gulch), the Montanos and the Pinitos (pines), in the Villaldama district, and La Paloma (the dove), or Iron Mine, in the Monclova district. The San Rafael appears to lie in granite, or a heavy-bedded gneiss, presenting most of the characteristics of the latter, though the contact plane of the limestone is not far off. It is certainly worthy of attention that the ore occurs in that portion of the crystalline rock, which is nearest to the limestone, and it has been thought by some observers to be a true contact vein. It is well known that veins of this character are very often distinguished for constancy and richness. Although the undersigned cannot entirely free himself from the impression that this proximity of different formations has had an important influence in the origin of the part of the vein on which this mine is situated; still he was unable to establish it actually at the contact of the limestone and granite, but rather a short distance within the latter. Two openings of the Riojas vein were respectively in limestone and in rotten whitish granite, but this fact, if established (as by the correspondence of the strike line of the vein in direction with that of a line joining the

Jan 1, 1884

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By A. S. Keh, H. A. Wriedt

The Precipitation of nitrides in quenched Fe-N alloys, aged between 25° and 200°C, was studied by transmission electron microscopy. Different dislocation substructures were introduced into the materials by recrystallization, cold working, and by Phase transformation prior to the introduction of nitrogen. It was found that the precipitated nitrides, tentatively identified as Fe16N2, have (100) habit planes. Nucleation takes place Preferentially at dislocations and at subboundaries. It sometimes occurs in the matrix, probably on vacancy clusters, but rarely on high-angle boundaries. The process of nucleation on dislocations and subboundaries is very temperature dependent. At room temperature there is no particular orientation relationship between the dislocations involved and the (100) planes on which the nitride Particles formed. With increasing temperature, the nucleation sites tend to become restricted to those dislocation segments lying in (100) planes. The change of yield stress of the 0.022 and 0.043 pet N alloys during quench aging can be correlated semiquantitatively with the change in particle distribution. Strain aging in quenched alloys can be separated into two stages. The early stage is attributed to nitrogen segregation to dislocations and the later stage is associated with precipitation. When previously quench-aged specimens were strained and aged, no additional Precipitates could be seen, although a considerable amount of strain aging occurred. DURING the past two decades, the precipitation of nitrides from a iron has been extensively studied by various techniques. It has been established that two types of nitride exist. The stable nitride, Fe4N, forms at temperatures above 250oC and Fe16N2, the

Jan 1, 1962