Search Documents

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By A Unlutepe

The Bosphorus Rail Tunnel Project, located in Istanbul, Turkey, aims to provide a Euro-Asian rail link, via an immersed tube tunnel crossing the Bosphorus Strait, along which will run all commuter, freight and intercity passenger trains of Turkish State Railways (TCDD), as well as the future extension to the European rail network. The total length of upgrading and new railway construction will be approximately 76 km. The main structures include the immersed tube tunnel; mechanised shield tunnels; new Austrian tunnelling method (NATM) tunnels; cut-and-cover, at-grade and retained-cut/fill structures; and some service structures. This paper discusses Phase 1 implementation of the project, one of the major transportation infrastructure projects in the world today, whose varied structures present stimulating engineering and construction challenges.

Jan 1, 2008

I HAVE to thank the members of the Institute most cordially for the honour conferred upon me in selecting me President, which position my poor services have prevented my filling adequately. I have, therefore only been able to stumble through my year of office under the guiding direction of our esteemed Secretary. I fully appreciate the honour done to me; and, now that it is over, I can look back with pride and pleasure at having occupied the chair; but I am told that it remains for me to fill one of the requirements of our Institute and present you with what has been dignified by the name of a presidential address. My relief in complying with this is in the knowledge of its freedom from the usual discussion which appertains to papers presented by our worthy members. It has been usual in the past for the subject chosen to be specially connected with the work immediately engaging the attention of your president, and on this occasion I would like to break away from this time-honoured custom and engage your attention for a brief space on what is equally dear to us all namely, Ideals of the Profession. In doing so, the retort of Whistler to an art student gives me, I must admit, much misgiving, for, on being asked how he developed his artistic talents, replied that he painted what he saw, which produced the immediate reply, "Ah, but the tragedy will come when you see what...

Jan 1, 1909

By P Grieve, J L. Mauk

The Central Maratoto Valley in the Coromandel Peninsula contains a sequence of veins in pervasively altered dacite + andesites of the Waipupu Formation. We recognise at least eight different vein types: (1) pyrite stringers, (2) quartz + carbonate veins, (3) crystalline quartz veins, (4) carbonate veins, (5) chlorite + carbonate veins, (6) siderite veinlets, (7) siderite + carbonate veins and (8) carbonate + pyrite veins. The overall temporal trend of the veins is from early pyrite to quartz and then to late carbonate veins. Carbonate veins and pyrite stringers both form planar and irregular veins, whereas some carbonate veins have diffuse contacts with the wall rock. Gold and base metal sulphides are associated with some of the quartz + carbonate veins. Textures within the veins reflect open space filling and multi-phase reopening. A partial record of hydrothermal activity has been preserved by vein crosscutting relationships, hydrothermal alteration minerals and fluid inclusions. Hydrothermal alteration minerals display zonation from south to north. The alteration increases from unaltered to weak propylitic alteration of andesite in the south (MVRCDC1), to sericitic alteration of andesite and dacite in the north (MVRCDC3). The alteration assemblage is dominantly sericitic, with no adularia present, drawing parallels to the Thames region where there is no adularia.

Jan 1, 1999

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

The paper discusses the special mixing requirements for Metallurgical Plant Design and outlines the problems associated with the agitation in Mineral Processing Industry today. It also covers new applications such as state of the art large leach tanks and backfill for deep mining.

Jan 1, 2004

By G Siboni, A Correa De Araujo, M Gotelip Barbosa, M J. Venturini

In support of the development of its Liberian iron ore project, ArcelorMittal Mining Research and Development (AM Mining R&D) has performed characterisation and beneficiation test work on drill core samples received from the proposed mine area. In addition to this, a sinter feed product was composed by blending and processing the drill cores in order to predict sintering performance of the ore. This article presents the methodology used to prepare the drill core blend for characterisation, as well as describe the sinter pot trial. The results are presented, demonstrating how important this type of study is for the development of an iron ore deposit.CITATION:Gotelip Barbosa, M, Siboni, G, Venturini, M J and Correa de Araujo, A, 2017. The use of drill core blends to predict sintering performance, in Proceedings Iron Ore 2017, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By M L. van Kampen

The Resource Management Act 1991 provides for activities to be classified as permitted, controlled, restricted discretionary, discretionary, non-complying or prohibited in district and regional plans. This paper looks at the use of the prohibited activity status to restrict, in particular, mining. Often the use of prohibited activity status for mining appears to have no basis other than the negative perceptions that the local community and/or the planner drafting the plan has toward mining and quarrying.   The paper will address the current appeal regarding the use of prohibited activity status now before the Court of Appeal, and the history to the litigation. The relevance of the outcome of the appeal to the minerals sector will also be explained.

Jan 1, 2007

By X Zhang, B McFadzean, C T. O’Connor, S Pikinini

The Platreef in South Africa contains one of the world’s largest reserves of platinum group elements. One of the major platinum group minerals (PGM) components in this ore is sperrylite (PtAs₂), which has been found to be slow floating compared to the other PGMs. In a study aimed at determining the reasons for the poor floatability of sperrylite and to improve its recovery, tests were carried out to determine the interactions of the mineral with a range of standard and novel collectors. Microflotation tests were carried out to determine the hydrophobicity of the minerals before and after adsorption of collectors. In addition, experiments were carried out to determine the enthalpy and extent of collector adsorption on the minerals and to investigate electrochemical interactions between sperrylite and selected standard collectors. The results indicated that poor collector adsorption was the major cause for the poor floatability of sperrylite. Sperrylite had both poor natural (14.5 per cent) floatability and collector-induced flotation recoveries, the highest recovery of 26 per cent being observed using PNBX collector at pH 9. Moreover, the rest potential tests showed that the interaction of sperrylite with standard collectors such as xanthates was poor. The decrease in potential after the addition of the standard collectors ranged from 7.9 mV to 24.9 mV under alkaline conditions. Furthermore, sperrylite rest potentials remained unchanged with a change in pH from basic to acidic, indicating its resistance to surface alteration. Surface alteration of the minerals is key for the chemisorption of collectors to take place on the mineral surface. This was further emphasised by flotation recoveries at low pH, where only certain collectors responded positively to a decrease in pH and these were shown to have undergone a structural change. This work has highlighted the difficulties associated with sperrylite flotation and provides some direction for future research.

Aug 24, 2022

The areas of concern lay in the processing of, and the subsequent hearing into, Waihi Gold's resource consent applications to extend Martha Mine. The proposed amendments to the Resource Management Act 1991 might see the introduction of contestability in the processing of applications - which would have assisted Waihi Gold; and the use of commissioners to hear the applications, with a right of appeal to the Environment Court on points of law only. It is also proposed to have major applications heard directly by the Environment Court. If Waihi Gold's applications had been heard at first instance by the Court, the delays in time and associated costs would have been reduced. However a hearing by commissioners only would not have been satisfactory, there being no right of appeal against the conditions of consent, which if implemented as granted by the Councils would have had a significant impact on the costs associated with the extended project.

Jan 1, 1998

By Woodcock J. T, Sparrow G. J, MacRae C. M

The external urfaces and interiors (as polished sections) of particles of coconut hell and extruded peat activated carbons taken from everal Australian carbon-in-pulp operations were examined with an optical micro cope, a scanning electron microscope, and an electron microprobe.Calcium carbonate (calcite) precipitated from the pulp was the major inorganic material on the external surfaces of the carbon particle, but several ore minerals, including quartz, hematite, pyrite, arsenopyrite, and clay minerals were also identified, along with trona, gypsum, a nickel cyanide, and a magnesium salt. Sections of carbon particles showed that calcite was virtually the only introduced inorganic material inside the carbons.It was distributed in the pores and cracks throughout the coconut shell carbon particles but tended to be concentrated in the outer layers of the extruded peat carbon particles. The mechanism of calcite formation and deposition is uncertain. Gold X-ray dot maps showed that gold was distributed through to the centre of coconut shell carbons and to a depth of at least 500 µm in extruded peat carbons. The distribution of gold within the carbon particles was similar to that of calcite.

Jan 1, 1988

Low displacement fault zones often comprise a mesh of interlinked faults, extensional-shear and purely extensional vein fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major through going faults. Mesh formation generally involves hydrofracturing (Pf > s3, at least locally) and the condition Pf ~ s3 to be maintained for the mesh to remain a high permeability conduit, requiring fluid over pressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc. Fluid redistribution in the crust is influenced by maximum hydraulic gradient (not necessarily vertical), by existing permeability anisotropy arising from bedding and other forms of crustal layering, and by structural permeability developed under the prevailing stress field. Strong directional permeability develops in the s2 direction, parallel to fault-fracture intersections within the mesh and orthogonal to fault slip vectors. In particular tectonic settings, stress-controlled permeability allows strongly focused flow through fault-fracture meshes with high potential for mineralisation. Favoured localities for mesh development include short-lived link structures along large-displacement fault zones such as dilational jogs, lateral ramps, and transfer faults.

Jan 1, 1995

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

Lead isotope measurements indicate that lead from the A.B.H. Consols mine and two transgressive veins in Browne's shaft is "Thackaringa" type and not "Broken Hill" type.

Jan 1, 1970

By S M. C Verryn, K Deysel

In heavy mineral sands ilmenite, rutile and zircon are present in economic concentrations. These minerals are important sources of Fe, Ti and Zr for various industrial uses. The beach sands of northern KwaZulu-Natal, along the Zululand Indian Ocean coastline in South Africa, have been mined for 30 years. The various processes involved in mining and processing these minerals have been controlled by time-consuming and labour-intensive analysis methods which, in some cases, can be replaced by X-ray powder diffraction (XRD)-Rietveld analysis. Heavy minerals are concentrated in the plant to produce a heavy mineral concentrate (HMC). The heavy mineral extraction plant is controlled and informed of the proportions of minerals in the HMC according to their magnetic susceptibility. The different fractions are called magnetic, paramagnetic and non-magnetic fractions and quality control is based on their magnetic fraction weights combined with X-ray fluorescence (XRF) elemental analysis. This current quality control process is very time consuming and labour intensive. We have aimed to show that we can, by XRD, identify and quantify all the minerals in the HMC and also in the magnetic separations. These results are then compared with results obtained by Mineral Liberation Analyser (MLA) as well as with the results from the physical separation. It was possible to detect all minerals present in the material by XRD and use the Rietveld method for a full bulk mineral quantification. A maximum of 15 minerals can be included in the Rietveld refinement due to computational restraints. Major minerals detected are rutile, ilmenite and zircon and minor minerals are quartz, epidote, anatase, amphibole, monazite, magnetite, titanite and augite. The XRD and MLA results correlate relatively well and detailed results will be presented for HMC and magnetic fraction samples. Small differences were observed for some minerals due to the different ways in which minerals are detected or due to preparation methods within each method. Rutile seems to be more abundant in the XRD analysis and the detection of Anatase is possible by XRD, but not MLA. Leucoxene (consisting of mainly microcrystalline anatase, rutile and titanite is not detectable by XRD since it is not a mineral, but ilmenite alteration phases are observed instead. There is, however, a correlation between anatase, titanite and rutile detected by XRD and leucoxene analysed by MLA.

Jan 1, 2008

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974

By N E. Whitehead

An application to mine an ilmenite-rich sand deposit in Westland led to public concern about potential radioactive hazards should the ore be further processed to recover zircon or monazite. A review recommended that any material involved in the heavy mineral sand industry containing more than 0.05% thorium, uranium or their mixture should be considered a radioactive substance and, for mining purposes, a notifiable product. Safeguards for those occupationally exposed would operate via the Radiation Protection Regulations. The major safety requirement would be the minimisation of dust in certain operations.

Jan 1, 1993