Search Documents

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

By A Castleden, G Cavanough, M Kochanek, J Cunningham

ROES« is a proposed new mining system for underground hard rock mines. Ore is accessed from within a shaft, which is located close to or within the stope, and pitched either vertical or within approximately 20 degrees of vertical. The shaft is designed to exclude personnel entry so production drilling and explosive placement is done using remotely controlled or automated machines. Routine remotely controlled survey of the shaft, stope back and broken rock within the stope is typically done following each blast. The survey may include excavation geometry, rock fragmentation and geotechnical characteristics. Blastholes are surveyed before placement of explosives. This provides mine operators and engineers with real-time data, allowing them to monitor production performance and risk factors so that they can make rapid changes as required. ROES« is designed to apply to open stoping or sublevel caving situations either in disseminated, geologically defined, thick tabular or narrow vein orebodies. The technologies developed for ROES« will also have potential applications to block caving operations to reduce the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES« will reduce the amount of stope-associated development by about half and therefore will allow ore to be brought on-stream sooner and at significantly reduced cost. Other savings are expected to flow from the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity. CSIRO and Orica Mining Services are developing the required technology and AMIRA is seeking sponsorship for a project to trial the mining method. This paper details the ROES« method, expected benefits and applications and includes typical stope and mining block designs and design requirements.

Jan 1, 2008

This is the time of year tor the presidential address, and with the present incumbent engaged in the coal mining industry, it will therefore come as no surprise to you that the theme of my address this evening is concerned with coal.There are other reasons for this apart from my contact with the coal industry. At present, coal is supplying considerable overseas revenue at a time when the remainder of the mining market is in a somewhat depressed state. That times will change goes without saying, if history is to be believed.However, so far so good for coal. My first reaction when The Institute indicated its wish that I be president for 1976 was to become deeply conscious of the honour bestowed on me.On consideration, I realized that very few past presidents have been intimately connected with the coal mining industry to the extent of indulging in it for lengthy periods as a full time occupation or, conversely, a part time interest for a long time. It also appears that not one had started their career in the industry. In my case, 'also, there were 8 very interesting years ,as a gold miner and metallurgist before commencing in coal.It therefore seemed appropriate to endeavour to discover ,why this should be so, as coal mining is now a very important part of a very important industry. What were the reasons why the industry took so long to emerge when there were ample reserves of easily accessible coal?Frankie and Johnnie in their bar room epic of the depression years concluded, and I paraphrase, that "their story held no moral, their story told no tale". If my story has such a message, it could perhapsbe construed as reinforcing the oft-repeated dictums, true or false, that "history repeats itself" or "man never learns".Coal mining is by far our oldest major Australian industry except for agriculture. Its history is almost as old as that of settlement:For various reasons, there has been a glamour associated with metal mining ventures which prob...

Jan 1, 1976

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By J J. Cilliers

The aim of this paper is to give an overview of the FrothSim flotation simulator and to demonstrate its ability to predict the performance of real flotation circuits. Example simulations are presented in which the feed rate to the circuit is varied, followed by simulations in which a cleaner section and recycle loop are added to the rougher bank.The simulator is able to predict both the recovery and the grade produced by the cells at all locations in a circuit and the simulator is shown to produce plausible grade recovery curves. It also demonstrated that the performance of banks of cells improve as the feed rate to the bank increased (improved grade for a given recovery), but that more cells are required to give the same overall recovery.

Jan 1, 2005

Dr. F. L. Stillwell. Segnit's article puts forward the views that the rocks associated with the Broken Hill lode are simply highly metamorphosed sediments, tbat metasomatism on a large scale was not an important factor at Broken Hill and that the rocks and lode were contemporaneously metamorphosed.In particular, the garnet quartzite, the most abundant rock in the limited section of the mine examined by Segnit, is described by him as a simple, metamorphosed manganiferous sediment.These views, while consonant with those of H. F. King (1958), are drastically opposed to those of myself and others e.g. Gustafson et al. (1950, p. 1383) who state that the most extensive hydrothermal alteration in the district is in and close to the zinc lodes in the Zinc Corporation and New Broken Hill Consolidated Ltd. mines. Segnit's conclusions conflict with 1. the absence of any manganiferous sediment in the Broken Hill district except in close proximity to the lode,2. the clear cut metasomatism of the dolerite dykes which indicates that the ore is younger than the dykes and therefore post-metamorphism, and 3. the petrofabric study of den Tex (1958) which provided independent evidence that the ore in its present form post-dates all events of a diastrophic nature in the area.The original sediments of the district were mudstones and calcareous sandstones with 2 to 5 per cent CaO. These have been converted by high grade metamorphism into sillimanite gneisses and quartzites characterized by the presence ...

Jan 1, 1962

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By A J. Gunson

The Norman B Keevil Institute of Mining Engineering, or the Department of Mining Engineering (the Department), at CanadaÆs University of British Columbia (UBC) is addressing the integration of sustainable development concepts into mining education and research on behalf of industry and society. Over the past decade, the DepartmentÆs education and research model has been evolving to incorporate collaborative and multidisciplinary strategies, where sustainability initiatives are taught in classes, supported in research and discussed in a voluntary collective of mostly graduate students û the Sustainability Working Group (SWG). The SWG has brought together a diverse array of disciplines from academia, industry, government, non-governmental organisations (NGOs) and mining communities. The operational mechanisms and structure of the SWG have enabled momentum to be gained through several multidisciplinary educational and research networking initiatives. It acts to attract new students with diverse backgrounds, foster innovative research, develop relationships and networks, and create the space to discuss progressive ideas and projects. The original cohort of SWG graduate students laid the foundation for sustainable research initiatives within the Department at UBC. Novel research has incorporated topics such as: community resilience, artisanal small-scale mining, sustainability indicators and corporate social responsibility, environmental assessment and impact benefit agreements and the recycling of waste. Propelled by the support of the Department and inspired by the works completed, a host of new graduate students have embarked on their research quests to integrate sustainability principles into their projects. Such projects include: social impacts and benefits of mining, artisanal small-scale mining, community health, the production and transport of mine pollutants, mine waste management, mineral process plant design and the evolution of community education and mine policy. This paper reports on the departmentÆs continuing research and development towards an understanding and evaluations of the ongoing contributions of mining to sustainable development.

Jan 1, 2009

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

Two key elements in the design of a pastefill or high density backfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: Vacuum or pressure filters. These represent the ætraditionalÆ approach to the preparation of pastefill. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producingpaste/high density backfills. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach.This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material. No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mines in Canada.

Jan 1, 1998

By S Udayakumar, S Biswal, N Sarmadi, V Sahajwalla, F Pahlevani

Recent times have witnessed a notable momentum in the interest surrounding technology dedicated to harnessing waste as valuable resources, prompted by the mounting challenges posed by waste accumulation and the swift depletion of natural resources. The carbon dissolution process within a molten iron bath stands as a pivotal reaction within the metal processing sector. The current study explores the utilisation of waste graphite electrodes (WGE) (obtained after being utilised in an electric arc furnace) as a secondary resource of carbon for dissolution into liquid iron. Experimental investigations were carried out at 1550°C using the sessile drop approach. High purity iron powder was used and the carbonaceous substrates were prepared from the ground WGE. The carbon pickup was determined using a suitable carbon analyser. Furthermore, an examination of the interfacial area between the molten iron and the WGE substrate was conducted beneath the metallic droplet, which effectively represents the iron/carbon interface. This interfacial analysis was carried out on two different samples obtained after a varying period of heat treatments at 1550°C. The interface layer was investigated using scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDS).

Jun 19, 2024

By S Maritsa, D Simbi, E K. Chiwandika, S M. Masuka

The steel industry is facing challenges on a global scale that include depletion of resources, huge energy consumption, and the emission of CO2. The demand for iron products is increasing due to the increased infrastructural development. Zimbabwe produced cast iron from scrap metals. However, there is currently a shortage of scrap, and yet Zimbabwe is rich in limonite ores that are currently being underutilised. The possibility of using limonite ore as a sustainable feed for pig iron production was investigated by preparing some limonite ore carbon composite pellets. The results showed that the addition of coal to the limonite ore and calcium carbonate mix to form the composite pellets resulted in a decrease in the drop number as well as the dry compressive strength of the composite pellets. This research aims to improve the physical properties of the green pellets by the careful addition of hydroxyethyl cellulose as a binder that was found to improve the physical properties of the green pellet. This is important for materials handling during the production process of the composite pellets. Results showed that the drop number was substantially improved by the addition of 0.4 wt per cent hydroxyethyl cellulose while the dry compression strength improved from 2.5 kg/pelIet to around 23 kg/pellet irrespective of the amount of binder added. The binder improved the physical strength of the iron-carbon composite pellets enough to allow for large-scale production of the pellets that can be an alternative and sustainable feed for cast iron production. However more results on the indurated compression strength and other properties such as the reduction degradation index, swelling index, and the reducibility test are required.

Jun 19, 2024

By D Brown, K Markovic, Z Tabor

From ancient times to the modern world, the mining industry has played a pivotal role in shaping the society that we live in today. It remains an integral part of everyday life and is a catalyst for both technological and economic growth. With finite resources on Earth, and growing pressures surrounding climate change and the environment, space mining opportunities have become of increasing interest. Recent discoveries have shown celestial bodies including the Moon and surrounding asteroids, contain an abundance of critical minerals, as well as resources necessary to sustain human life. These discoveries coupled with a transition into the digital and autonomous age, offer an innovative solution to solving some of the mining challenges currently being faced on Earth. Similarly, they also offer a pathway to enabling deep space exploration and off Earth exploratory missions. However, like with mining operations on Earth, space remains and immensely challenging and complex operational environment. The inhospitable nature of space poses new challenges, including communication barriers, lunar dust, cosmic radiation, and gravity. The challenges and risks are not just technological, as Environmental, Social, and Governance (ESG) factors must also be considered to prevent unintended consequences and hazards. Furthermore, future workforce, law, financial, and security systems must evolve to enable space mining to take place. These are all known aspects to begin with, but as the complexity of the space grows it becomes apparent that a holistic approach to assess and manage these factors will be required.

Sep 1, 2024

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

Information obtained from a reconciliation system provides fundamental indicators to an operations performance and is often neglected as a key performance indicator when developing a business plan or mining schedule. The cycle of exploration, ore definition, mining and processing within a company is constantly scrutinised both internally and externally as to the safety, environmental and financial performance of these activities with the operators judged on their performance on a periodic basis. However, it is not unusual for the reconciliation process to be given scant attention until a serious issue (usually a shortfall) occurs, at which point short-term solutions may be implemented which only serve to compound the original problem. A robust reconciliation system takes time to develop and implement initially and must continue to evolve with time. The best systems are those where all the stakeholders in the ultimate outcome are involved in the design and accept responsibility for the validity of their component inputs. Output from the reconciliation process can be utilised to fine-tune all aspects of an operation once the underlying issues leading to a particular result are understood.

Jan 1, 2002

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999