Search Documents

By Just GD, Gillies ADS

There is an increasing need for reliable and comparable coal resource data and it is necessary to standardize the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can consider- ably improve classification quality. A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed. Application of the method in classifying resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results which closely reflect the error associated with an estimate of resource quantities based on current sampling densi- ties. It requires a careful geostatistical analysis with emphasis on geological awareness. Resource category restrictions must be arbi- trarily assigned and remain constant for all deposits being compared. Engineering judgement is needed and interpretation may be required with isolated and peripheral blocks.

Jan 1, 1987

By L. Gilbert

Recent changes to environmental legislation and trends in the environmental regulation of mining in the Northern Territory are being driven by (among other factors) Federal Government policies and international agreements on the environment. These trends are discussed and the expected application of the NT Water Quality Management Strategy (based on the National Water Quality Objectives) over the next few years is examined with respect to mine environmental management practices. Some of the potential conflicts and changes in approach which may develop are identified and examples discussed. Proactive means of integrating trends in environmental legislation with mine planning and waste management are discussed.

Jan 1, 1994

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

This paper describes a steam outburst in a metal mine which occurred in December 1992 in Japan, resulting in two fatalities. The outburst occurred just after blasting in a heading face 600 m below surface (SL-50 m), 1664 m from a mouth of the mine. The scale of the outburst was large and the fragments of the outburst spread up to 34 m from the face, the total volume of the outburst was estimated to be 206 m3. The outburst materials were mostly clay originated from the typical surrounding rock of sulfide ore and basalt. The shape of the larger outburst fragments were slabs with a thickness of 10 to 20 cm. The victims were found in a main ventilation air shaft, 175 m and 380 m from the face, respectively. The mine mainly produces copper, lead and zinc. The face was ventilated by a 560 mm diameter duct with a fan and the strata temperature of the rock was estimated to be in the range of 120 to 140¦C. There is a famous hot spring near the mine. A thorough investigation into the unprecedented accident was made including an on-site inspection and investigation of rock characteristics in laboratories.

Jan 1, 2005

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

The Australian minerals sector has a shortage of skilled professionals to satisfy an industry that is experiencing renewed vitality. Graduate numbers are low throughout Australia and the world, while economic rationalisation is seeing many educational institutions downsize, or even close, their minerals-related programs. In addition to requiring more entry-level graduates, minerals producers are looking to update the skills of their current workforce to keep up with the industryÆs continuing technological revolution. To address the issue the Minerals Council of Australia (MCA) endorsed collaboration between several Australian minerals producers and a team of universities to generate the Mineral Tertiary Education Council, or MTEC. MTEC recently initiated a venture to increase the availability of professionals with relevant skills to the minerals industry. Primarily aimed at delivering postgraduate programs, the initiative will allow graduates from other disciplines to æconvertÆ to the minerals sector as well as provide professional development training to an existing work force. This venture represents a novel approach in that courses will be delivered by more than one institution and will employ innovative teaching materials with flexible and remote delivery formats. The programs will cater specially for professional development in the minerals sector, which generally requires high flexibility due to the nature of work conditions and locations.

Jan 1, 2004

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By C M. Côte, S Worden, K Svobodova

Mines in Queensland are transitioning to the progressive rehabilitation and closure plan (PRCP) framework. Mine operators are required to select and justify appropriate and viable post-mining land uses (PMLUs) following consideration of the surrounding landscape, community views and the objectives of local and regional planning strategies. The new approach offers opportunities for considering innovative PMLU options and collaborative use of post-closure mine assets, such as infrastructure (power, road/rail, buildings), dams and residual voids. Consideration of regional planning strategies will require a shift in thinking as mine closure is regulated and planned on an individual site basis and selection of PMLUs are commonly considered from this perspective. Planning at regional rather than site-specific scale offers strategic advantages, including the ability to align PMLU selection with the regional context and stakeholder aspirations (which could foster sustainable outcomes); address cumulative environmental and socio-economic impacts; consider options that are only viable at scale (ie across larger geographic areas); establish more extensive and connected ecological habitat corridors; reinstate larger expanses of functional agricultural land; and optimise regional resources (Hattingh, Williams and Corder, 2019). This paper presents the findings from a multidisciplinary project that identified PMLU options within Queensland’s four mining regions: the North-west Minerals Province, North Queensland, Bowen Basin and Clarence-Moreton and Surat Basin (Figure 1). To enable spatial analysis at the appropriate scale and to accommodate geographic diversity, North Queensland was divided into three geographical ‘focus areas’ – Weipa, Charters Towers and Tablelands. Delineation of the areas captured most of the mines within the wider region as well as regional characteristics and features.

Aug 2, 2023

The Honourable Neil Pickard has been in Parliament for something like sixteen years. He was Minister for Education in 1976, served as Shadow Minister in a number of portfolio areas while his party was in opposition, and since their return to power in 1988, he has been the Minister for Minerals and Energy. Ladies and gentlemen, I ask you to welcome the Minister, the Honourable Neil Pickard.

Jan 1, 1989

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

Strata bolting/dowelling reinforcement techniques are being reintroduced into the mines of the National Coal Board. There are strong reasons for the selection of the full hole anchorage principle of bolting and for the development of the wood/resin dowel. There are strong reasons also for the measurement of strata bed separation as the method of assessing the effectiveness of a roof bolting system. There are several designs of bolts. Instruments have been developed for investigation and control purposes. Different drilling and bolting machines have been employed in trial sites. In addition comparative laboratory model work has been conducted on simple non-bolted and bolted systems.

Jan 1, 1971

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By R Valenta, A Littleboy

Geological heterogeneity is one dimension of complexity in mining. Significant effort is put into developing an understanding of this complexity so it can be used in resource estimation, mine planning and economic modelling. However, over the decadal lifespan of a mining venture, many other dimensions add to the complexity of a mining operation. These include: technological evolution, market fluctuations; investor confidence; social norms; local expectations; and ecosystem functionality. As with geology, these factors are all heterogeneous, uncertain, time varying and represented through sparse and incomplete datasets. Recent work (Valenta et al) is beginning to show us how these risks correlate in different global settings. By analysing data relating to known, but as yet undeveloped copper deposits, this work (the complex ore body database) is demonstrating that it is the combination of issues (both price sensitive and non price-sensitive) that determine the viability of a deposit for extraction in the 21st century.CITATION: Littleboy, A, Plint, N and Valenta, R, 2018. Mining as a complex system: do we need a new model?, in Proceedings Complex Orebodies Conference 2018, pp 41–43 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

Mond gas-producer tar, and, in fact, all tars obtained from the retorting of coal where steam and air are admitted to the retort, are of entirely different chemical composition to the ordinary coal tar made in the gas or coke works. These tars contain none of, the aromatic hydrocarbons - benzene, toluene, naphthalene, and anthracene, sought after by the ordinary coal-tar refiner.The distillation of Mond tar shows it to consist of phenols of high molecular weight, unsaturated hydrocarbons of high gravity and low viscosity, paraffin wax, and resinous substances of whose composition little is known.The physical properties of Mond producer tar are also peculiar. It has a "short," granular texture when cold, which might be likened to candied honey. It "dries" (hardens) when exposed in thin layers to the air, and, for a coal tar, it cannot be considered sticky. This latterò property, combined with the short texture, prevents its being used successfully for road-making or macadamizing.The drying properties and the paraffin wax contained in: this tar cause it to hold up large percentages of water, probably in the form of emulsion. When containing as much as 10% to 15% moisture it appears to be quite dry.

Jan 1, 1918