Search Documents

Dilution in underground coal operations can be underestimated by up to five times during feasibility studies, with disastrous economic consequences. Every one per cent of stone waste introduced can reduce an in situ specific energy of 25 MJ/kg by some 0.25 MJ/kg and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some $A 1 million per year. This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation and presents the dilution trends from a continuous miner/longwall mine over an eight year period. The overall dilution level for the mine can be back-calculated by comparing the run-of-mine coal quality to the predicted in situ, undiluted quality. However, this will not identify the actual contaminant types, areas of the mine responsible for the dilution and the reasons for the dilution. This additional information is essential for controlling dilution to acceptable levels. Quality and horizon control using existing sampling information is generally only adequate for longer-term control purposes, and is not suitable for monitoring mining-induced dilution. The cost of close-spaced surface drilling to collect the information necessary for short-term control is prohibitive, particularly for deeper mines. However, much of this data can be collected through underground channel sampling and horizon control measurements taken during continuous miner development and longwall extraction. The mine runs the risk of not meeting contractual quality specifications and of increased equipment wear if this additional information is not available and the sources of dilution cannot be controlled. The information can also be used to plan longwall extraction heights on a short-term scale with resulting improvements in productivity.

Jan 1, 2003

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

Suppression of the explosion of the world population and the surprising increase of waste and emissions are major targets confronting mankind in this century. Recycling and waste minimisation are key words for sustainable development in a highly industrial society. The argument is really whether or not recycling done well is the solution to the environment problem for the following generation. If energy is not necessary in the recycling, all materials have to be recycled. The greatest interest among the environmental issues is the regulation of CO2 gas emission. It must be recognised that it is not possible to completely renew expended energy. Some of the recycling systems currently used are thought to increase the load on the environment rather than to be beneficial. Although metal industries have consumed tremendous amount of energy and discharged a large quantity of CO2 and solid waste, the metals have supported a high quality of life. The metal production industries such as the iron and steel industry and the non-ferrous metals industry can work well recycling of not only metals but also other materials without consuming more energy. Waste plastics, for example, are use as a reductant in a blast furnace. The role of metallurgical industry in the recycling-based society is introduced in the present paper to recognise how the metal industries can contribute recycling and waste minimisation.

Jan 1, 2002

By R G Warren

Most orebodies have cross-sections of less than 1 km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defined as `all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated fonn and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system of fluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: 1. sources of the mineralising fluids and transporting ligands; 2. sources of the metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common throughout time and space and are mappable on a regional scale. The delineation and empirical prediction of mineral systems can thus be approached by combining two components of metallogenic research. Firstly, the development of maps of regional geoscientific data and data sets of the distribution of factors significant for mineral systems in general. Secondly, the determination of the essential ingredients of particular styles or types of deposits in terms of mappable elements that any exploration program could focus on.

Jan 1, 1994

By N Patzelt, T C. Logan, I B. Klymowsky

In 2003, NEWMONT MINING CORPORATION, the worldÆs largest gold producer, set out to prove that High Pressure Grinding Roll (HPGR) technology is sufficiently robust and reliable to be considered for the treatment of hard rock gold ores. In collaboration with POLYSIUS, a significant trial was conducted and 127 600 tonnes processed, successfully proving the HPGR capabilities on the Lone Tree Mine, Nevada ore û one of the most competent and abrasive ores in the industry. The success has led a number of mining companies to consider HPGRs for the comminution of gold and copper ores.

Jan 1, 2004

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

By K Schiefelbein, P OÆGrady, R Balusu, T Ren, T Harvey

"An extensive research program has been undertaken over recent years to reduce the risk of fires and explosions in underground coal mines. The research projects have integrated extensive field studies and computational fluid dynamics (CFD) models of goaf gas flow behaviour to develop optimum proactive strategies to prevent and control spontaneous combustion and fires ingoaf areas. The research has developed a fundamental understanding of the air and gas flowbehaviour in goaf areas and provided a detailed understanding of the eff ects of various geological,ventilation, operational and inertisation design parameters on goaf gas distribution. The researchinvestigations have also provided a better understanding of the flow behaviour of gases from the heating in the goaf areas and the effect of various gas and spontaneous combustion controltechnologies and strategies. Field studies conducted at a number of underground coal mines have shown that the proactive strategies were successful in reducing oxygen ingress into the goaf areas and in reducing the risk of fires and explosions in the underground coal mines. The results of various research investigations and guidelines for reducing the risk of fires and explosions in underground coal mines are presented in this paper."

Jun 1, 2012

Petroleum exploration in the Australian arid zone has been proceeding at an ever-increasing pace, subject to financial fluctuations, since the 1960's. The impacts of petroleum exploration in the arid zone are less than they would be for corresponding operations in. e.g. a forest area: in this context, Australia is fortunate in that its major petroleum producing (and prospective) , basins are offshore or in the arid zone. In addition. the other major sources of impact in the Austrlian arid zone, namely pastoralism, tourism, and rabbits, tend to be concentrated around areas of particular conservation significance, whereas petroleum exploration is not. Despite this, the cumulative impacts of exploration are sufficient to have caused concern to government regulatory authorities and some sectors of the general public. Exploration is now subject to a range of environmental constraints with various degrees of legal enforceability. To enable exploration to continue without public opposition, the industry, and government agencies charged with regulating or supervising it, must demonstrate that the net benefits of exploration exceed net costs, including environmental costs. One particularly simple and cost-effective technique for increasing the net benefit/cost ratio of exploration is to reduce the net environmental costs by minimising and mitigating the impacts, both primary and secondary, of seismic acqisition. This is best achieved by a combination of preventive and restorative techniques: careful line positioning and low-impact (or zero) line clearance, coupled with simple rehabilitation of bladed lines. Line clearance without bulldozer blading - e.g. by rolling or simply pegging and trafficking, perhaps with tracked rather than rubber-tyred vibroseis - is one promising approach currently coming into use. Rehabilitation by grading soil banks ("windrows") back on to bladed tracks, though not yet in widespread use, has proved very successful in the limited areas where it has been applied to date.

Jan 1, 1987

Mount Isa Mines Ltd. annually extracts 5.6 million tonnes of copper ore from the 1100 Orebody. All production is by longhole open stoping, with an increasing emphasis on pillar recovery. Drilling and blasting prac- tices have been modified to allow more efficient pillar extraction, with the evolution of a "core and shell" approach. Blast design occurs at the stope design stage, while individual blast preparation is based on detailed ring plans. A programme of blasting research involving surface and under- ground vibration monitoring and fragmentation assessment has been car- ried out in conjunction with production personnel. Drilling and blasting practice in the orebody must continue to evolve with continued research, to suit changing conditions and take advantage of new technology.

Jan 1, 1988

By White A, Price G

The main assets of a mining company are its orebodies; the second are the people who find and use them.The graphs in Figure 1 were derived from a paper by Rob Macdonald of Rothschild Australia presented to The AusIMM Centenary Conference in Adelaide earlier this year. They show that the value of the industry on the Australian Stock Exchange halved over the past decade, despite the re-investment of capital equivalent to its full market capitalisation. Why is this so? The average dividend yields for the ASX Mining Index was never above five per cent during that period and barely averaged 2.5 per cent. Why then is $Ai million capital re-investment per employee since 1960 not enough to generate a rate of return to investors better than lousy bank interest? Do the investing public no longer regard our industry's assets to be world class?

Jan 1, 1993

Three transient phenomena have been observed and experienced in the operation of large solvent extraction mixer-settlers. These relate to the ability of the settler to discharge streams with low entrainments arising from different phase separation æproblemsÆ. The operation of large-scale laboratory and commercial solvent extraction settlers has been shown by a number of workers to be a dynamic process, especially at the feed end. Circulating flow patterns are common in all three organic, aqueous and emulsion phases. The circulating patterns in deep dispersion bands in long settlers are believed to form roll fronts that can travel down the settler length within the bounds of the dispersion band. Various physical models are proposed to illustrate the formation and movement of roll fronts within the dispersion band. Another transient phenomenon has been observed in commercial settlers operating without any dispersion band. Entrainment of the continuous phase in the advancing dispersed phase is at high and erratic levels. This supports the conventional separation model, which recommends the presence of a significant depth of dispersion band to æfilterÆ the secondary haze from the bulk separated phases. The third transient is the position and shape of the dispersion band within the settler. Large commercial settlers have been shown to exhibit high variability in both these aspects of the dispersion band. The elimination of all three transient phenomena in commercial settlers has been shown to be effective with an in-settler media of coarse size and moderate specific surface area. The effect of the media is two-fold: it dissipates both the circulating flows and the forward velocity of any roll fronts, and creates a stable deep dispersion band at the feed end that serves to trap secondary haze from the primary coalescence process. It is effective in treating both types of transients involving non-existent or excessive dispersion band depths. The media serves to enhance coalescence by providing a static surface of intermediate surface tension on which droplets can collapse. The random nature of the media also provides multiple stream splitting and re-combination, that presents further drop to drop and drop to media impingement, which in turn promotes coalescence.

Jan 1, 2000

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

By K S. E, S C. Parker, T K. Kundu

Understanding the fundamental principles governing the reactions at surfaces has always been the goal of theoretical surface science. The atomistic simulation techniques have been used to calculate the surface structures and the stability of quartz and wollastonite, and their adsorption behaviour in the presence of molecular and dissociative water, and the two widely used collector head group molecules of methanoic acid and methylamine. The dissolution behaviour of wollastonite has also been modelled. The calculated surface energy, hydration energy and reaction energy values have been examined and discussed in the light of flotation literature. These studies have given an insight into the interactions at atomic level, which indicate that modelling techniques should be capable of predicting the adsorption behaviour and to design the selective collector molecules, which is of central importance to the mineral processing technique of flotation.

Jan 1, 2005

By McKenzie C, Michaux S

Modern quarrying operations focus attention on blasting operations as a critical component in the overall cost-effectiveness of quarrying. Generally, optimisation of blasting has been linked to the processes of drilling, explosive consumption, secondary breakage, and product haulage to the primary crusher. This approach gives no consideration to the impact of primary crusher feed size distribution on downstream processes, or on the quality (ie shape and strength) of the final product. Blasting operations can be manipulated to produce a wide range of muckpile size distribution. This paper presents the results of studies into the impact of muckpile fragmentation on downstream crushing and screening operations, and includes measurements of primary blast oversize and muckpile fragmentation, together with measurements of size distribution, circulating loads and flakiness for various process streams throughout a quarry processing plant. This paper is an extension of other studies investigating the prediction and control of fragmentation from blasting, and the role of explosive performance in controlling muckpile fragmentation.

Jan 1, 1995

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

By S P. Suthers, J M. F Clout, J J. Campbe

An advanced technique for modelling hydrocyclone separation performance has been developed. This technique is based on the combined modelling of hydrocycloning parameters and ævirtualÆ iron ore feed. The virtual feed modelling was performed using a novel (in-house) software package called æRecognitionÆ, which uses data from optical image analysis to classify the particles in certain size fractions according to total iron content and calculates data for every grade class. These data include the average mineral composition and density of every liberation class in every size fraction. This information about every size fraction, representing the ævirtual feedÆ, was input to the mineral processing modelling package USIM PAC. The hydrocycloning process was then modelled for this virtual feed using the Plitt hydrocyclone model. Empirical calibration coefficients for the hydrocyclone model were calculated using an optimisation procedure in Excel. Pilot-scale hydrocyclone beneficiation experiments were performed on an iron ore blend, using different hydrocyclone pressures and per cent solids in the feed pulp. These experiments were modelled and the modelling results were compared with the experimental results. The new modelling approach enables prediction of the recovery of each mineral in the products, calculation of the total iron grade and recovery, and optimisation of iron ore beneficiation using hydrocyclones.

Jan 1, 2005

By I Ametov, G Levay

It is now common practice to use substantial amounts of recycled water in mineral processing plants to minimise both environmental discharge and withdrawal of fresh water from often limited water resources. Recycled water additions to process water are frequently obtained from sources such as tailings dams, tailings thickeners and concentrate dewatering. It has been suggested for some time that addition of recycled water to process water will impact the quality of the process water and that changes in water quality may influence flotation performance. To date, investigations of process water quality changes as a result of water recycling have been limited and as a consequence there are very few data available to substantiate these ideas. Thus the impact of recycling on process water quality remains largely unquantified. Over recent years we have conducted water quality studies at a number of mineral flotation plants with varying degrees of water recycle. This paper describes the results of these investigations, including data which suggest that build up of salinity due to recycling while it occurs, is reduced by fresh water make-up. The fate of flotation reagents such as collectors, promoters, frothers and flocculants during process water recycling has also been investigated. Results show that process water concentrations of these reagents vary from plant to plant, but that, with the exception of frothers, most reagents are generally removed from the system through mineral adsorption. In general, the results of these investigations suggest that recycling process water will not result in continuous increase in solute concentrations as appears to be the commonly held view.The effects of changing water quality on flotation can vary. In many cases, flotation conditions can be optimised to suit the water quality, while in others, treatment of the water may be necessary to obtain acceptable plant performance.

Jan 1, 2009

Applications of chlorine metallurgy to the extraction of metals often result in the production of volatile metallic chlorides, most of which condense directly to a solid phase at one atmosphere pressure. A stirred bed condenser suitable for th

Jan 1, 1980

By E A. Agorhom, P N. Aabulleh

The bulk of the worldÆs production of iron ore is processed into steel. The needs of the steel industry therefore demand a high exploration and exploitation of iron ore. One trend within the industry has been a great increase in the demand of iron ore and this is reflected in an increase in world steel production from 1955 to date. In addition to the high demand for steel, is ChinaÆs high appetite to feed its steel industry. It is therefore important that the iron ore potential of Ghana is showcased for eventual exploitation by potential investors to meet this enormous demand for the commodity in the industry globally. Ghana has three main iron deposits of potential industrial and commercial importance. They are: Shieni sedimentary iron ore (reserves: 1.270 X 106 metric tonnes), Pudo titaniferous-magnetiferous iron ore and the Opon-Mansi lateritic iron ore deposits. The Opon-Mansi iron ore deposit occurs in the Western region of Ghana. The ore deposits are located on top of the range of 15 hills, which extend over a distance of 24 km from Opon-valley, south of the Western region to Dunkwa. The area has an estimated 147 Mt of iron deposit, with Fe content of 52.5 per cent. This paper looks at the iron ore potential of Ghana and how it is capable of attracting potential investors to exploit this valuable mineral for global consumption.

Jan 1, 2007

By Goto T, Sato K, Mori N

A field investigation by making use of the seismic method has been carried out in order to comprehend the mechanism of rockburst and gas outburst and their predictive measures. The seismometers were so arranged both on the surface and underground as to enclose a mining panel. Seismic signals detected by the array were recorded and processed by the 32-kwords computer system. At present the system is available for analysing the source location and Richter's scale of each event and for visualizing the distribution of seismic foci and released energy at any mining stage. The magnitude distribution of events can be regarded as a comparable index of the seismic activities among mining panels. An analysis of the spatial density distribution of seismic energy in the mining panel can be useful to distinguish a highly stressed zone from stress released areas. The energy released curve or the rate of energy release determined from seismic data is also a good indication of the seismicity.

Jan 1, 1980