Search Documents

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

By Mauk JL, Arehart GB, Mathews SJ

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases. The 818Oqu i values of individual bands within the vein material range from 7.3-10.9%x. Calculations show that the 818Oqäa,u values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

By Reid JG, Cutfield S

Considerable quantities of dissolved nickel are lost in the waste liquors from the QNPL nickel treatment plant. Cementation, precipitation and ion exchange techniques were investigated to reduce this loss. Ion exchange was the most successful of the procedures studied and a process for recovering nickel from stripped ammoniacal process liquors was developed in the laboratory and scaled up to plant flow volumes. The system developed uses a carboxylic ion exchange resin operated in a completely ammoniacal cycle. The regenerant is itself regenerable using existing plant, thus the only loss is the stoichiometric value of NH4+ required to displace the exchanged cations from the resin. Existing plant sand/anthracite filter beds have been adapted for use as resin columns containing 3 cubic metres of resin capable of treating effluent at a flow rate of 6000 litres/min.

Jan 1, 1978

By Estoque J, Lodrigueza L, Rebillon F

Ore mineralization in Masara consists mainly of gold-silver veins, porphyry copper and pyrometasomatic deposits related to left-lateral movements along the Philip- pine fault system and a later stage of magmatism. These are hosted by pre-Tertiary volcanic flows and volcaniclastics, and comprise a temporal pattern of earlier peripheral copper zone, an intermediate mixed copper-gold area and a later central gold vein system within the Masara sector of the postulated volcanic field. Gold ore emplacement occurred in at least two stages, and shows gradations from a lower mesothermal-epithermal phase passing into a typical epithermal zone, and finally into a truncated, or poorly developed, upper level thermal spring deposit. Orebodies are closely associated with hot springs, solfatara and several magma- related masses, emphasizing their inherent linkage with a geothermal system in the Area.

Jan 1, 1987

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By Sneyd R. J, Walton M. C

In early 1987 Minproc acquired a license from the inventor to engineer and construct acid plants incorporating the Fattinger technology. The process offers a simple and reliable method of producing sulphuric acid from metallurgical off gases at significantly lower capital and operating costs than the more familiar contact process. The process also offers the simultaneous production of nitric acid, if the NOx content of the off gases is high enough. A development of this latter process has other applications within the minerals industry, particularly in conjunction with refractory gold ore preoxidation.

Jan 1, 1989

Parallel lenticular orebodies occurring at the C.S.A. mine of Cobar Mines Pty. Ltd. are mined by mechanized cut and fill stoping over the full strike length. Access is provided for each stope lift from an inclined drive adjacent to the orebody. Mobile drill jumbos mounting hydraulically-operated booms are used for drilling upholes which are subsequently charged with ANFO explosive.Close control of drilling has been found essential for good back conditions and to ensure optimum fragmentation.Broken ore is transported from the face to the main ore pass by rubber-tyred, diesel-powered, load-haul-dump units. Initially, the units trammed ore to the main pass via the incline drive. As the stopes advanced and the lead distances increased, stope passes were developed in the wall rock and raised concurrently with each stoping lift. The passes terminate in drawpoints and production loaders are used to transport ore from the drawpoints to the main ore pass system.Two parallel ore pass systems have been developed to cater for both copper and copper-zinc ores. These systems terminate above a 48 in. by 60 in. jaw crusher. The crushed ore is conveyed to a traversing rock box and thence to one of two crushed ore bins adjacent to the main hoisting shaft. A loading station conveyor is interlocked with the winder to provide automatic ore hoisting.All phases of ore handling have been mechanized as completely as possible. Results to date indicate this policy has been vindicated but highlight the need for tight operating control and close liaison between operating and maintenance personnel.

Jan 1, 1969

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By Leahy GJ, Wright DJ, Player RI

The operation of a one tonne submerged combustion pilot plant for the recovery of copper from anode furnace and converter slags is described and the effects of variables discussed. Using coal as reductant, copper levels of anode furnace slag were lowered to 1% or less, with batch times of approximately 120 minutes. Fluxing with limestone was required to produce a fluid slag at temperatures of 1200 - 1300¦C. For converter slags, reduction to 0.5% Cu or less was achieved in batch times of 35 minutes. The chemistry of the pyrometallurg- ical recovery of copper is briefly reviewed in relation.to copper recovery methods.

Jan 1, 1978

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

By G W. Wilson, P Ritchie, N A. Currey

The design and rehabilitation of potentially acid forming (PAF) waste rock dumps is site specific, being a function, among other factors, of the rock types, the dumping and storage method employed, and the climatic setting. The æstore and releaseÆ cover system developed to manage acid rock drainage (ARD) from mineralised waste rock dumps at Kidston Gold MinesÆ open pit operations in the semi-arid climate of North Queensland, Australia, has been monitored for seven years. The paper describes the philosophy behind the design of the PAF dump and æstore and releaseÆ cover system and the adaptation of the cover system over time to suit KidstonÆs conditions. The results of monitoring over the seven years since the first cover was constructed are presented, and the approach being taken at Kidston to ensure that the risk of impacts from any residual ARD is accommodated and to facilitate lease surrender are described. The Kidston story is a valuable case study of a successful approach to remediating an identified source of ARD in a semi-arid climate, which has actively engaged all Stakeholders.

Jan 1, 2003

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

By C J. Adams, H J. Campbell, T Popham, A Goodall

Pounamu is a MSori collective term for semi-precious stone scientifically referred to as nephrite, semi-nephrite, jade or bowenite (tangiwai) that is composed predominantly of metamorphic tremolite in a felted, fibrous texture. It is Aotearoa/New ZealandÆs icon mineral material. Ownership and management of this important taonga (treasure) has been vested in Te Rnnanga o NgSi Tahu as part of a Treaty of Waitangi settlement process. Increasing demand from the tourist, jewellery, fashion and sculpture industries, as well as cultural renaissance, has placed pressure on the pounamu resource. This had led to nephrite importation, allegations that foreign material is being marketed falsely as New Zealand pounamu, and wider concerns over the potential for exploitation/over-use and theft of genuine pounamu.   Research is underway to characterise different pounamu source regions by defining their ægenetic fingerprintÆ. The geological age and radiogenic isotopic composition of Aotearoa/New Zealand pounamu is distinguished from other nephrite jade occurrences overseas, due to relatively young cooling ages. Strontium isotope ratios distinguish pounamu from different source areas within Aotearoa/New Zealand (whakapapa), with signatures reflecting the host terrane rocks (their family) and their position in a sequence of metamorphic events (their generation). The research will provide a tool for archaeological research, trademark and resource protection.   Mineral resource assessments normally aim to define the total volume/tonnage present, which is generally assumed to be finite, applying drilling and geostatistical modelling. Pounamu resource assessment requires a different approach, as its intrinsic value is insufficient to warrant modern exploration methods (eg drilling, geophysics). Pounamu is only known to occur at a restricted few in-situ (hard-rock) localities. It is primarily found in transported (alluvial) detrital river and glacial outwash deposits, where collectable material has short term variability due to erosion and transport processes. A new methodology is being developed aiming to define: +        the total resource present, +        the relative rate of change in the availability of that resource through erosion and other geological processes, +        active areas where new material is likely to be exposed (eg by erosion), and +        appropriate extraction rates for sustainable use. The methodology will provide a holistic overview of the resource in different regions of Aotearoa/New Zealand, and may be applicable to other transient or restricted natural resources that occur within geologically active environments (eg supplies of driftwood on beaches).

Jan 1, 2005

By S Gannon, J Abols, T Hughes

In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilises conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX«100å ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a three-stage crushing circuit to crush the gold ore to minus 1 mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJs and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plantsÆ design, commissioning and operation are discussed.

Jan 1, 2006

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

By Bhaskara Sarma P V R

Solvent extraction of cobalt from an ammoniacal ammonium sulphate medium was carried out using Di(2-Ethyl Hexyl) phosphoric acid in kerosene as diluent. The effect of ammonium chloride and ammonium sulphate on the extraction efficiency was studied. The extracted species in the ammonium chloride and sulphate systems were CoAz2HA.NH4CI and CoA3.HA.2(NH4)2SO4, respectively. Ammonia scrubbing and cobalt stripping studies were carried out from loaded and ammonia free organic Respectively.

Jan 1, 1992

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

The factors affecting performance of base and precious metal smelting and converting processes are considered in relation to reactor characteristics. The chemical differences between processes are related to these factors for different reactor systems. The complete smelting and converting flowsheet involves a number of operations. The process selected for a particular feed and product requirement should be one which optimises the efficiency of the process, the cost of building and operating the technology and the long-term maintenance and productivity of the units.Ausmelt's approach to achieving an efficient process using its technology is described in relation to the smelting of copper concentrates for production-of blister copper.

Jan 1, 1992