Search Documents

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

By T Gibbons, M Korte, C Brent, K Runge

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and steadily increased production from the original 119 t/h design capacity to 265 t/h milling throughput in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of under- ground with open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate.Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Minerals Process Technology Asia-Pacific and South America (MMPT) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently, with surveys of both the crushing/ grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model such that overall process optimisation was possible. Two key outcomes for the operation are exploration of the operating limits of the currently installed plant, and projection of the logical next stage of potential capital plant expansions. This paper covers Part B or the flotation component of the project. A separate paper discussing Part A or crushing and grinding is also being presented at this conference. Surveys of the Osborne flotation circuit were performed along with a comprehensive review of the cell characteristics including measurements of the gas and froth phases of individual flotation cells. These data resulted in a size-by-size floatability component model of the complete circuit. This circuit model was then used to perform steady-state simulat- ions to evaluate options to improve both overall circuit and individual cell performance. The grinding circuit model discussed in a separate paper or Part A of this project was then used interactively with the flotation circuit model to recommend the best operating regime to maximise overall efficiency. For example, the balance between increased crushing and grinding costs versus higher copper recovery and final concentrate grade. Due to changes in market conditions in the fourth quarter of 2008, the focus was shifted to prioritising operational changes rather than capital expansion modifications, in order to improve circuit performance.

Jan 1, 2009

By K Barbosa, G Wilkie, F Reyes, V Jokovic, C Evans

The idea behind Grade Engineering is to exploit the natural heterogeneity of an orebody (spatial, temporal) in order to divert low-value waste out of the mining value chain. Essentially, this involves rejecting material at relatively coarse particle sizes (10 mm to 200 mm). However, lack of knowledge about the inherent particle grade distributions in these coarse particle size ranges limits the opportunities for optimisation. Particle grade distributions are essential for quantifying and modelling gangue liberation and yield curves. These curves can then be used to predict the mass and value flows that will go towards the accept and the reject streams. Particle grade distribution information for particles coarser than 10 mm can be collected based on chemical assays of sufficient number of individual particles. However, for smaller particles (1 mm to 9 mm), a significantly larger number of particles is required for assays. Moreover, in some cases, the mass of individual particles is smaller than the minimum mass required for chemical assaying. Also, other quantification techniques such as automated mineralogy, eg Mineral Liberation Analysis (MLA), require extended measurement times to analyse statistically representative numbers of particles at these size ranges. This work investigates the use of 3D X-ray microtomography to fill this quantification gap at these size ranges (1 mm to 9 mm). In-house image processing algorithms are used to estimate the mineral/metal content in each particle. Particle grade distributions, as well as density distributions, are thus produced without a minimum mass requirement and with each scan providing information about tens to hundreds of particles at a time. Mineralogical data from MLA analysis, of finer size ranges, is used to inform X-ray microtomography, so a simpler 3D mineral map can be obtained using the image intensity. Chemical assay information of the scanned samples is used to validate and correct the mineral phase segmentation.

Aug 24, 2022

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By Williams DJ

Preliminary calculations suggest that spoil piles in the Bowen Basin will undergo approximately 4 m settlement as the ground water table recovers after mining is abandoned. Approximately 1 m of differential settlement is possible. Superimposed on this will be a long term creep settlement of 1-3 m/log cycle of time. Depending on the nature of the spoil material, partially submerged spoil piles could be sufficiently stable although to ensure stability during long term creep it may be necessary to flatten the final spoil pile face to approximately 25¦.

Jan 1, 1987

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020

The Lower Palaeozoic Woolomin Association is composed of chert and jasper (often radiolarian), siliceous argillite, the mafic volcanics with associated hyaloclastites, and occasional greywacke and limestone lenses. Several "Cyprus-type", conformable pyritic copper (+/- zinc and cobalt} sulphide lenses are spatially related to individual mafic volcanic units and manganiferous chert and/or jasper. The Association has been interpreted to represent an oceanic crustal remnant generated either in an island arc environment (Herbert, 1981) or at a divergent plate boundary (Scheibner and Glen, 1972; Leitch, 1974a, 1975) later to be obducted, or tectonically emplaced, into continental crust; the adjacent Peel Fault was considered to be the palaeo-obduction zone (Scheibner and Glen, 1972) and the associated alpine-type mafic/ultramafic complex, an ophiolite (Crook and Felton,1975).

Jan 1, 1990

The blasting of the 2190_6095 stope at Kimberley Nickel MineÆs Sally Malay operation in Western Australia is an example of what can be achieved with electronic detonating systems when a drill and blast engineering team is faced with complex blast geometry and a major pump station in close proximity to the stope. Using Dyno NobelÆs HotShotÖ system, the engineering team successfully designed and initiated the 36.5 Kt stope firing, with a powder factor of 0.35, resulting in no damage to the pump infrastructure, better fragmentation of the ore and less overbreak in what had previously been a geotechnical and geometrically challenging stoping environment. This paper will discuss the design parameters used for this stope blast as well as the benefits the operation found in using precision detonator timing in this 252 hole shot over two levels using a combination of up and down and slashing rings that were initiated in four different directions.

Jan 1, 2007

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu&apos;s research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta&apos;s case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

Over the last thirty years production of heavy minerals from Australian deposits has dominated the world market. The main incentive has been to suoply the raw material for titanium dioxide based pigments. These ~ninerals include ilmenite, rutile, leticoxene and more recently, synthetic rutile. Inevitably the viabilit/ of developing placer type deposits has seen influenced by other heavy minerals present, such as zircon and monazite, but these have been of secondary importance. For most of the sixties and seventies, Australia supplied the &apos;najority of free world rutile and zircon, and a large proportion of the ilmenite. With the run-down of rutile- rich reserves in eastern Australia, the emphasis has s:iifted in several countries, including Australia, to fill }the gap with i l Wen i to and its derivatives, leucoxene, synthetic rutile and titanium rich slag. over the next 15 - 20 years, as high grade beach placers in Western Australia are mined out, less traditional sources for mineral sands products will be opened up. Low grade placers (particularly those dominated by ilmenite) will be reassessed in Australia, U.S.A., Africa and Asia, and exploration will shift from beach and dune environment, to heavy mineral concentrations in alluvials, lake deposits and continental shelf deposits. At the same time, production of anatase and bastnaesite will be expanded, as required, from the huge resources contained in carbonatites in 3razil, U.S.A. and China.

Jan 1, 1986

In current mining practices it is desirable to bring about a substantial increase in both rate of face advance and productivity, thus compelling the mine engineer to consider better and more productive ways of mining. Transportation plays a vital role in achieving improved productivity. This paper focuses on horizontal transportation systems. Horizontal transportation is defined from the shaft station area to the end of the stope cross-cut. Traditionally, horizontal transportation is inefficient in comparison to vertical transportation efficiencies and accounts for a high proportion of South African mine accidents. Thus, the role of horizontal transportation has been investigated in detail, as it offers the greatest chance for improvement. The purpose of the paper is to provide a best practice guideline for the design of horizontal underground transport systems. It is intended that the document be used by mine designers and planners as an aide memoir during the design process and benefit may well be gained from retrofit and reorganisation activity. The paper looks at transport systems suitable for deep level gold mining in South Africa and evaluates such items as management, scheduling, and haulage systems. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2003

Much has been written about leadership over the years. It is probably one of the most written about but least understood and defined concepts in business. Leadership and management are often confused and blurred, and inspirational words such as mentor, coach, motivator and the like, are often interspersed when describing a leader. There are a few things we do know about leadership:The only thing common to all leaders is that they are different.Leadership is not the sole domain of business; it applies to every aspect of human endeavour. We are all required to lead at times, and we all have it in our ability to lead. There is no set of predetermined competencies, which a leader must possess to be effective. Hence there is no course in the world that can teach you to become a leader. There is no such thing as the perfect leader. Leadership is a verb, not a title; you actually have to do it to be judged a leader. All leaders no matter how you define the term, must leave a legacy. Thus in the busy world we all live in, what are the lessons in leadership that we can all learn from, that will assist us all in our pursuit of leadership. The purpose of today is to put forward a framework for leadership that I have been researching and working on for many years. It is not the definitive framework, merely a framework. Out of today you will take your own collective thoughts, learnings, observations, experiences, education and training, and collective wisdom, and apply it to yourself.

Jan 1, 2004

By S Planeta

The use of explosives in underground mining has its drawbacks, particularly in the case of thin or narrow vein type deposits. Due to that, there is a need to develop more discriminative and safe rock-breaking technologies. Mechanical rock splitting seems to be one of the most promising avenues in this respect. This paper describes briefly principles and features of radial-axial splitters. It reviews a feasibility study done to evaluate a potential of this technology in selective mining. It was intended to compare productivity and cost of ædrill-splitÆ mining with conventional cut-and-fill method. Hypotheses and assumptions adopted, methodology used and the obtained results are presented and discussed. The study has confirmed an interesting potential of radial-axial splitters in mining thin and narrow vein deposits. In conclusion, it is stressed however, that it will take more R&D work to corroborate the results obtained. Some suggestions concerning future research in this field are also given.

Jan 1, 2003

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar&apos;e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By S C. Dominy

Current and proposed methods of resource classification relate to the geological, economic and technical confidence in the estimated resource. Geological confidence is, however, only vaguely defined. It is largely related to the level of drilling and sampling, to the geologistÆs perceived level of confidence in his/her work and on the continuity of the mineralisation. Rarely has any real attempt been made to assess how well a deposit has been explored, sampled and evaluated and how accurate or realistic the geological model is for the deposit. This contribution reviews the impact of two of the potential sources of error, ie sample recovery and quality. The first of these parameters is measured during logging and assaying, but is often forgotten during grade and tonnage estimation, and resource classification. Preliminary studies have shown that modelling of this parameter is a valid exercise, which should accompany the evaluation of grade and other economic parameters. The sample recovery factor for an ore block can then be used to reassess the confidence in the block. It could, for example, downgrade the status of a Measured Resource to an Indicated Resource even though standard methods might indicate that the higher classification is applicable. A method is proposed by which this recovery factor could be incorporated into current resource classifications producing a more sophisticated and comprehensive measure of sample quality. A review of the sources of error naturally leads to the assignment of scores to each stage of the evaluation process, depending on the methods used and assumptions made. Sample recovery is one important factor, which is likely to appear at several stages. These scores can then be weighted and combined in a manner resembling that used in the CSIR Rock Mass Classification. This score will then allow the resource estimate to be rated on a scale from 0 to 100 per cent to produce a Quality Control Index (QCI). However, this index must then be modified using an Evaluation Difficulty Index (EDI), which reflects the difficulty of a particular style of mineralisation to accurate resource estimation. This results in the production of a Resource Reliability Rating (RRR), which can then be linked to international classifications, such as the 1999 JORC; 2000 CIM; and 2001 EURO codes. This will permit a more precise definition of geological confidence levels or, combined with estimation error, produce a classification system in its own right. This same rating can also be used as the basis for technical audits of mineral projects.

Jan 1, 2002

By J Rowland, B Belle, M Webber

The Australian underground coal industry has experienced substantial improvements in longwall productivity and, as such, the methods of providing a safe and productive mine environment have needed to evolve and develop. Whilst the primary method of controlling atmospheric conditions is by airflow it has become impracticable or impossible for the majority of Australian longwall mines to contend with all environmental hazards with primary ventilation alone.If the ventilation circuit cannot provide a safe and productive mine environment at an acceptable cost and circuit duty then supplementary controls are required. Examples include pre-gas drainage, post-gas drainage, gas utilisation, refrigeration and innovative dust control systems. Of the 21 longwall operations surveyed in Australia, there were 13 in New South Wales and eight in Queensland.This study represents a timely opportunity for the industry to examine the primary and supplementary ventilation systems implemented in Australian longwall mines and to discuss how to equip the industry to successfully face the future of underground longwall ventilation management in Australia.CITATION:Webber, M, Belle, B and Rowland, J, 2017. Australian longwall ventilation systems, in Proceedings Australian Mine Vent Conference 2017, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017