Search Documents

An integrated approach to risk management to complement insurance is the sustainable way forward for the modem organisation. For risk management to work, its various aspects need to operate interactively, not in isolation from insurance. This is the approach recommended in this paper. The risk management process is a strategic method for reducing an organisation's total cost of risk. Well established and basic risk management techniques will help identify and achieve risk management Objectives.

Jan 1, 1994

By C Antonio, R Narayan, A Scheuermann, S Quintero, M Edraki, M Ziemski

Tailings are mostly loose material and can be classed as non-plastic sandy silts. They also tend to have low permeability, resulting in slow consolidation (settling) rates and low shear strength, even after consolidation. These qualities make them prone to liquefaction and, therefore, physical instability. In contrast, coarse waste rocks possess high shear strength and permeability when stacked in dumps. However, air and water flow-through the voids can cause acid mine drainage (AMD) with significant undesirable environmental implications. Combining the two waste streams before disposal by mixing presents a potential opportunity to harness the desirable properties of both waste streams. This practice is termed co-mingling and is prevalent within the coal processing industry. Co-mingling of metalliferous mine tailings is, however, a relatively new concept. By combining the coarse waste rocks and fine-grained tailings streams, the fine tailings tend to fill the voids between the waste rocks, reducing hydraulic conductivity and advective air (oxygen) flow into the rocks, thus possibly reducing acid mine drainage (AMD). Conversely, tailings are introduced to large frictional particles from waste rocks, providing reinforcement, stability, and possibly improved drainage. New separation methods are being introduced to the mining sector, which have the capacity to extract waste with significantly larger particle sizes. High Voltage Pulse (HVP) is a technology in which relatively coarse particles ranging in size from 30 to 100 mm are exposed to an electric pulse discharge. This pulse preferentially fractures mineralised particles while leaving unmineralised rock (gangue) intact. The stream can then be passed via a screen, with smaller mineralised particles reporting to the undersize and removing coarser unbroken barren particles, thereby eliminating waste. Coarse particle flotation (CPF) is another emerging new technology in metalliferous mining that applies flotation separation to coarser particles than conventional flotation. These new technologies produce different tailings (waste) streams with varying physical characteristics and possibly surface chemistries. This research aims to test new tailings mixtures by applying the co-mingling concept to blend the reject streams generated by these two technologies (HVP and CPF) with the tailings produced by conventional flotation. Combining different waste streams before disposal can improve stability and potentially reduce the acid mine drainage (AMD) rate, thus enabling early access to the tailings storage facility for rehabilitation and closure.

Aug 2, 2023

By Huafu L, Ruishi N, Hongnian Y, Qinglong Z, Yangshen S

The Dongshan terrane was first recognized in 1984 (Guo,et al., 1984, 1989) as an old continental crust block of migmatized granitic gneiss in the Southeast Coastal Hercynian-Indosinian orogen, and it was thought to have occured on Dongshan Island, which has an area of less than 100 km? Recent research work has shed much light on the geology of the Dongshan terrane.The Dongshan terrane is approximately 40-50 km wide and 380 km long, trending NE. It runs from the region of the mouth of the Ming River through Putian and Huian Counties, Amoy and Dongshan island of Fujian Province to Nanao island of Guangdong Province, bordering the southern segment of the coastal region and coastal islands of Fujian and eastern tip of Guangdong Province. The Dongshan terrane is divided from the Zhejian-Fujian Mesozoic Volcanic Mountain Chains by the Changle-Shaoan fractural zone, and its eastern boundary is covered under water in the Taiwan Straits.

Jan 1, 1990

In-seam drilling is conducted mainly to drain coal of gas and/or water prior to development or extraction. The requirements of inseam drilling for gas drainage have mainly surpassed the technical limits of rotary drilling and are mainly being addressed by guided down hole motor drilling, albeit at a higher cost. There is an increasing application of in-seam drilling to detect geological structures or other hazards or their absence in advance of mining to reduce the risks of underground mining. Close collaboration between miners, drillers, geologists, researchers and suppliers over the last four years has seen many advances made to improve the accuracy and reliability of inseam drilling. With such developments will come closer control over the ventilation and safety of future mining under deep gassy conditions, but not without costs. The paper summarises the current applications of inseam drilling, recent technological advances and the next generation survey and geophysical sensing tools which are currently being developed

Jan 1, 1998

By S C. Dominy

The Minerals Education Australia program is offering a tertiary learning environment for the global mining industry. The Minerals Council of Australia has instigated this initiative, which is run by the Minerals Tertiary Education Council. The program is a pioneering partnership between the Australian minerals industry, Australian governments and key Australian universities. It is designed to deliver key undergraduate and postgraduate courses for tomorrowÆs minerals industry professionals in the fields of geoscience, mining and minerals engineering and metallurgy. The flagship course for geoscience professionals is the G3 Masters program. This is a coursework-based degree supported by the Minerals Tertiary Education Council, and a partnership between James Cook University, the University of Tasmania and the University of Western Australia. These partners represent the leading-edge providers of minerals geoscience education and R&D in Australia. The G3 program provides the full spectrum of post-graduate training skills in exploration, mining and economic geology topics.

Jan 1, 2003

The Professional Standards Act responds to the growing problem of professional liability by introducing a mechanism whereby professional associations can have schemes approved. Those schemes include a cap on liability; a requirement for compulsory insurance; the development of risk management strategies; and the establishment of a complaints and disciplinary system. The Act is also designed to support and develop the concept of self-regulation by the members of occupational associations who provide services to the community by providing them with those tools. It implicitly accepts that self-regulation is preferable to statutory regulation and that self-regulation serves the interest of the community and of the providers of services. The Act arose from a review of professional liability commenced in 1988. The Attorney General's Department produced an Issues Paper, released in September 1989, which outlined in detail the extent of the problem. This was widely circulated and an extensive number of comment were received.

Jan 1, 1995

Large scale rhyolitic volcanism is an important process at some convergent plate margins because it leads to chemical differentiation of the upper.-crust and is responsible for the production of long lived near surface thermal anomalies; the Taupo Volcanic Zone is.a Quaternary example. The main features of the magmatic systems-of the zone. are the existence of large high level chambers containing homogeneous silicic magma which erupt at intervals of thousands to tens of thousands of years. Geochemical work on the deposits resulting from these eruptions has shown that with few exceptions the magmas have been remarkably uniform in their . composition throughout the history of the zone although individual batches with lifespans of the order of. one hundred thousand years can be recognised by subtle differences in trace element ratios. Basalt is a rare proportion of the rocks exposed at the surface but has played a major role as a medium for heat transfer and as an end member in chemical mixing processes.

Jan 1, 1987

Ordovician metasedimenIs near the Karamea Bend and east of Ihe upper Carboniferous Karamea batholith were intruded by acidic stocks during the Cretaeeous. K/ Ar dating of two of the stocks gave 110 ± 3 millionyears whereas the batholith granite gave 290 8 ± million years. All but one of the stocks mapped lie on an approximately ENE line along which they show gradation in composition, texture, and alteration.Most of the intrusions have produced homfelsic haloes in the surrounding rocks but the hydrothermal alteration centred near the head of Questa Creek is quite distinct. Here much wider zones of alteration are characterised by chlorite, green biotite, sericite, and quartz-orthoclase in order towards the centre, though no stock crops out. Each zone of stronger alteration is heralded by "spots" containing the next characteristic mineral.It is suggested that a late phase of the intrusive period that gave rise to the outcropping stocks also gave rise to a volatile-rich intrusion still hidden beneath the head of Questa Creek.

Jan 1, 1976

By S Strohmayr, R Harvey, A See

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore were chalcocite, bornite, secondary chalcopyrite and native copper while the primary zone has only chalcopyrite. The variability of the supergene zone made concentrator operation difficult and predicting metallurgical performance using mineralogy essential to establish the capabilities of the concentrator. A paper presented at the 1998 Mine to Mill Conference entitled Mineralogy Controlling Metallurgy at Ernest Henry Mining (Barnes, Strohmayr, Brindley and Munro, 1998) presented the testwork and initial plant surveys that showed that the mineralogy of the ore controls the metallurgy of the concentrator. This paper presents the data obtained from the subsequent years of operation treating both the supergene and primary ore types. A review of the actual supergene mineral distribution in feed and subsequent recoveries compared to those predicted as part of the flowsheet design is also presented.

Jan 1, 2003

By P O. Andersson

Mining of sill pillars is more difficult than the ordinary mining. The sill pillar mining is performed under more difficult conditions and the mining of the sill pillar itself produces more problems; failure of the rock due to high stresses, difficulties in controlling the fill above, overall stability of the stope and special requirements on the technique for backfilling. Altogether this makes sill pillar mining technically difficult and often not profitable. A project was therefore initiated with the aim to increase the mineable ore reserve by making sill pillars mineable, both technically and economically. The project aimed at developing technique for already existing sill pillars as well as planned sill pillars. For the existing sill pillars a technique would have to be developed for mining beneath unstabilised fill. For sill pillars that would be created in the future, the most suitable mining method and methods of supporting or stabilising the fill in the stope above was to be chosen within the project.

Jan 1, 1998

Mine haul road design at Bougainville Copper Limited has undergone significant changes since mine start-up. Selection of 95 tonne trucks and the subsequent replacement by 155 tonne units is discussed, with particular reference to haul conditions within the mine. Changes to haul road design and construction practices are detailed which have lead to improved standards and tyre life. INTRODUCTION Bougainville Copper Limited operates one of the largest copper mines in the world at Panguna, Bougainville Island, in the North Solomons group of Papua New Guinea. The mine commenced commercial operation in April, 1972 and current planned production is 198 000 tonnes of material per day, of which 115 000 tonnes is ore averaging 0.46% copper. Annual total planned production is 72 000 000 tonnes to yield approximately 150 000 tonnes of copper with significant quantities of gold and silver. The mine operations workforce now consists of national employees up to General Foreman level.

Jan 1, 1982

Quality Assurance has become a buzzword amongst governments and industry. Notwithstanding the world class work done by its committees in developing codes of ethics and of practice in field geological handbooks, mining cost estimation handbooks, and reserve estimation, the AusIMM could better prepare its membership for QA. MICA could provide a simple set of guidelines to enable consultant members to develop their own QA procedures manual conforming to AusIMM Codes and to IS09003, and AS3903.

Jan 1, 1994

In recent times there has been a marked increase in public awareness of air pollution. Some of this has been induced by the Press but our own senses tell us that there is a visible haze over our cities on many mornings. The people are now demanding a clean environment and will no longer tolerate smoke and dust fall or gaseous and odorous emission which either soil building and furnishings or interfere with comfort and well being.

Jan 1, 1971

Legislation, if it is to be effective, must be enforceable by the state and acceptable to the industry. In the mining industry the relationship between the government inspector on the one hand and the mine management and employees on the other, must be one of full co-operation before the system can be effective. To understand our present system, which is-duplicated in most countries of the world, an examination of the history from which it evolved is necessary.

Jan 1, 1975

It is a great privilege to be invited to give this address at this centenary conference. A centenary is a time for recollection, for celebration and for looking ahead. The AusIMM has much to celebrate and many things to recall. I hope in this address to make some useful comments about Australia's future (and mindful of but not forgetting New Zealand), looking ahead for 25 years or so, and the mining industry's role in that future.

Jan 1, 1993

By S Nowosad, O Langefeld

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination plants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade; the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence. These two works consisted of rock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination. The transport of ore from crusher to furnaces, from furnaces to chlorination barrels, and the emptying of leaching vats was effected entirely by hand labour. The system of chlorination was what was, known as Mears process, chloride of lime and sulphuric acid being used in the chlorination barrels, and as the time allowed...

Jan 1, 1911

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

In terms of tunnelling the mining industry is generally thought of as the crude cousin of the civil construction industry. Mining has tended to concentrate on speed and flexibility rather than the high standards required in civil tunnelling. Historically this difference has been based on the belief that such high standards were not required by the mining industry, they would slow down the development of the project and as a result increase the costs and extend the time period between start up and a positive cashflow.For civil works the construction of a tunnel is the project, for mining the construction of declines, crosscuts and drives are merely the means of accessing the orebody so that the real work can begin û MINING. Extraction of ore is the core business of most mining companies û it is what pays the bills.Though most mining companies have the equipment, the people, the knowledge and the ability to excavate tunnels, in the past mining companies did not appear to put the same energy into their tunnelling operations as they put into improving their ore extraction operations. In the past decade this appears to have changed, many mining companies now realise how important the correct excavation of a decline is to the success of the overall mining operation. They began to recognise that there were cost benefits to be gained in using the correct development techniques without overly sacrificing the benefits of speed and flexibility.This recognition also coincided with the growth of underground contractors whose predominant work was primary development (declines and ore access crosscuts and drives). The contractors again had the same knowledge, the same people, and similar equipment but their focus was different from that of the mining company û the contractors were focused on the development of the mine, the excavation of declines, crosscuts and drives. These deliverables were the contractorsÆ core business û itÆs what paid the bills.

Jan 1, 1999