Search Documents

By Richard Morland

Some simple and fundamental objectives To challenge and inspire our people to embrace safety as a value ?A stand for safety as a value ?A stand for our people ?A stand by our people ?Prevent harm to our people ?Eliminate suffering for individuals, families, friends, colleagues

May 1, 2010

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the &apos;cleavage fronts&apos; of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By B. Wasmund, M. Y. Solar, I. Candy

The nickel laterite industry is divided into two camps when it comes to the grade of the ferronickels produced. One group, led by Falcondo and Cerro Matoso, markets high-grade ferronickels in the range of 35 to 40% nickel, while another group, led by SLN and the Japanese smelters, favour lower grades in the range of 20 to 25%. Because the ores processed by these smelters vary widely in terms of nickel content and iron to nickel ratios, it is probably more accurate to classify these smelters in terms of their iron recovery: Falcondo and Cerro Matoso smelt at lower reduction potentials and thus recover only 15 to 30% of the iron in their ores, while SLN and the Japanese smelters are very reducing and recover 45 to 65% of their iron. Low reductions generally imply higher slag losses and lower nickel recoveries, but also lower power and reductant requirements; higher reductions, the reverse. The question is, therefore, whether an economically optimum ferronickel grade exists for processing any given ore. This paper proposes a methodology for determining this optimum grade and concludes that nickel laterite smelters should favour low reductions and production of high-grade ferronickels.

Jan 1, 2008

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC&apos;s confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By Lauri Gregg

Key Message Energy focused Change Management Process that engages operations managers is the missing tool needed to build capacity for energy/GHG management

May 1, 2007

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By M. Pearson, W. Bristowe, A. Hanson

"There&apos;s no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors&apos; experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006

By Neil Campbell

Abstract Following discovery on the Giant property of very promising gold deposits, some of which terminate against the steeply-dipping West Bay fault, a geological study was initiated co locate possible faulted extensions of the ore. Geological mapping revealed that the ore and the shear zones to which the ore is confined are older than the fault and therefore subject co displacement by it. It also disclosed several diabase dykes which seem co provide the best basis for determining the fault movement. After applying various techniques co determine their strikes and dips, the dykes were used as structural markers and it was estimated that, subject co certain possible errors, the movement on the fault was 16,140 feet (3.06 miles) south and 1,570 feet (0.297 miles) down on the west side relative co the ease. Evidence supporting this conclusion was obtained when subsequent deep diamond-drill holes intended to test the hypothesis cut an ore-bearing major shear zone which, so far as can be determined, is nearly identical with its present correlative on the Giant property. Introduction The fault under consideration follows a northerly trend past the west side of the original settlement of Yellowknife, which is situated 600 miles north of Edmonton and 400 miles from the Northern Alberta Railway terminus at Waterways, Alberta. The mining properties chiefly concerned include the southern part of the Giant claims, on the east side of the fault, and the Con-Rycon-Demelt claims, on the west side, 3Y2 miles to the south. Geological data were also obtained from the eastern part of the A. Y.E. property, which lies south of the Giant claims, and from the Negus, Meg, Yellorex, and Kam properties, which are south and southeast of the Con-Rycon-Demelt claims. Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault which appears to be the greatest, resulted from the work of Dr. A. W. Jolliffe (McGill University, formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply-dipping dislocations of the earth&apos;s crust. In the winter of 1939, a mineralized shear zone named the Creek Vein was found on the Giant property. It was noticed that the space relationship between the new shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acidic flows lying north of the Con property. Coupling this relation with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear.

Jan 1, 1947

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985