Search Documents

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By Mohsen Amir-Rahmat

The ore of Sarcheshmeh copper deposit that has been located in the south ?east of Iran, contains four type of rock that they have their specific hardness and strength according to their alteration type and mineralization. Blasting of these various types of mine rocks prepares various types of size for the product of mine as the feed of concentration. Along the crushing of this feed a few factors effect on the efficiency of the crushing unit. The aim of this project has been the consideration of the effect of ore size on the efficiency of crushing unit. For this investigation along the year 2000 A.D., six sample from feed and six sample from product of crushing unit have been prepared. The results of the screen analyze of these samples has shown that the size of feed has been lesser than the primary plan and the size rate of the product has been bigger than the primary plan. Also in this research the effect of feed size on the quality of product size has been considered.

May 1, 2003

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By Côme Carbonneau

The ten -year case history of La Société Québécoise d&apos;Exploration Minière (SOQUEM) is reviewed under the headings of the company&apos;s raison d&apos;être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m&apos;[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By Lynn M. Gould

Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13 percent of Canada?s total oil requirements. To do this, Syncrude mines the oil sand in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB) is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States. As parts of the Mildred Lake Base Mine reached their economic life, they were replaced with new facilities at the Aurora satellite mine. Aurora is situated on Oilsand Leases 10, 12, and 34, 35 kilometres northeast of the Mildred Lake facility. (Figure 1) In 2000 the first hydrotransport low energy extraction production train started up at Aurora. A second production train is scheduled for start up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320 ton to 380 ton payload capacities.

May 1, 2002

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel&apos;s duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004

By V. “Ram” Ramachandran

"In view of the increasing number of environmental regulations that have been promulgated all over the world in the last thirty years, non-ferrous smelters and refineries have had to learn and adapt to treating process bleed waste streams containing heavy metals. The result of such treatment invariably yields a gypsum-saturated solution containing salts such as alkali metal sulfates, chlorides and fluorides. Presence of anions such as sulfates, chlorides and fluorides in the discharge streams – presently not a major problem- are coming under increasing scrutiny and will have to be addressed in the near future. It is envisaged that discharge limits for sulfate ions will be in place in the near future. Treatment of brackish water to produce drinking water also results in brine streams containing alkali salts that have to be addressed for proper disposal. This paper reviews treatment options for such streams containing high levels of total dissolved solids with emphasis on sulfate removal. Areas covered would be: a) chemical treatment for removal of various constituents that make up the total dissolved solids b) processes for sulfate removal processes –thermal and non-thermal-to recover and reuse of treated water and c) brine use and treatment options.INTRODUCTIONThe rising cost of water and meeting the ever-changing stringent environmental discharge regulations make water recycling and reuse essential. The metallurgical industry has used water as a medium for dissolving and/or rejecting metals and chemicals in addition to removing thermal energy. Any excess process effluent is collected and sent to end-of-pipeline treatment and ultimately discharged to surface water for disposal under a permit. The conventional- and probably the cheapest way -of treating metal-bearing process effluent streams is lime neutralization followed by sulfide polishing for elimination of heavy metals to produce a stream that meets NPDES discharge limits. This results in a stream containing dissolved solids.These dissolved solids normally comprises of inorganic salts. The possible constituents are cations calcium, magnesium, sodium and potassium. The anions are sulfate, chloride, fluoride, nitrate, carbonate and bicarbonate. In addition to these constituents, the treated effluent streams contain very small amounts of heavy metals, oxyanions such as arsenites, arsenates, selenites and selenates. Process streams from gold operations contain residual cyanide. Small amounts of ammonium ions are also present in these streams based on the pH of the solution."

Jan 1, 2012

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By Henri-Louis Jacob et Marc Bélanger

La province de Québec est un important producteur de roches et de minéraux industriels. En 1998, la valeur de cette production se chiffrait à 1,26 milliard de dollars canadiens (données préliminaires). Les minéraux industriels produits comprenaient: l'amiante extraite des gisements de chrysotile associés aux complexes ophiolitiques de Thetford Mines et d'Asbestos; l'ilménite et les scories enrichies en titane produites à partir du gisement d'ilménite massive du lac Tio associé au complexe anorthositique du lac Allard; le talc produit dans la région de Thetford Mines, à partir des roches à talc-carbonates associées à des feuillets de serpentinite; le mica broyé produit à partir de l'intrusion de suzorite du lac Letondal; le graphite en paillettes extrait du gisement du Lac-des-Îles; la wollastonite extraite d'une zone de skarn dans un lambeau de roches métasédimentaires enclavé dans le massif d'anor-thosite du LacSaint- Jean; le sel extrait aux Îles-de-la-Madeleine d'un gîte associé aux évaporites du Croupe de Windsor. Les nombreuses carrières dans le sud du Québec produisent, en plus de la pierre concassée, diverses substances incluant la pierre dimensionnelle (granite surtout); le calcaire pour la chaux, le ciment ainsi que divers usages industriels; la silice extraite à partir de formations de grès ou de quartzite. Le Québec est aussi un important producteur de tourbe de sphaignes qui est extraite de vastes tourbières qui se sont formées un peu partout dans le sud du Québec à la suite de la dernière glaciation. Les autres ressources en minéraux industriels comprennent des gîtes déjà exploités de brucite, de chromite, de magnésite dolomitique et de feldspaths ainsi que des gîtes de magnésite, de barytine et d'apatite faisant présentement l'objet d'évaluation.

Jan 1, 2001

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By M. J. Fairweather

"The development of means to maximize the selectivity between galena and sphalerite in lead zinc ores is extremely important to the lead-zinc industry. Two challenging studies recently undertaken by Cominco will be reviewed. The first required an unusually fine grind to achieve liberation between galena and sphalerite. The second contained partially altered galena which resulted in unusual early activation of sphalerite under normal flotation conditions. Means by which lead and zinc separation were optimized in these two ores will be discussed.There are two important factors in the separation of minerals by froth flotation: particle size distribution (grind) and pulp chemistry. Pulp chemistry includes a number of factors including pH, Eh, collector type and concentration, inorganic depressants, organic depressants and activators.Grind is important for two reasons. A sufficiently fine grind is required to optimize liberation. However, if the mineral dissemination is too fine, mineral selectivity in the flotation process is impaired. Due to the hydrodynamic constraints of conventional mechanical flotation cells, flotation works best over the single decade size range between 10 and 100 microns. The majority of new ores treated by Cominco until relatively recently were comparatively simple. The major factor in their treatment was defining optimum grind size. Accordingly, the focus within mineral processing at Cominco was on grind and supporting liberation studies. The relationships between grind, liberation and flotation response are intuitively easy to understand. An idealized relationship is shown in the first figure."

Jan 1, 1991