Search Documents

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By J. A. Allan

The utilization of natural deposits of salt is one of the oldest industries in Alberta. In 1820, Sir James Richardson visited Salt river, and in the same year D. W. Harmon states chat "clown Slave river, there are several places, where almost any quantity of excellent dean white salt may be taken, with as much ease as sand along the seashore. From these places the greater part of the northwest is supplied with this valuable article". This reference is to the salt chat occurs around springs on Salt river at the northern boundary of the Province. This and other occurrences will be described later in this paper. It is not on account of the development of salt and gypsum in Alberta chat this paper has been prepared, but rather to draw attention to the widespread distribution of salt-bearing and gypsum-bearing rocks, and to the stratigraphic importance of these rocks . The origin of the deposits of salt, gypsum, anhydrite, and dolomite is discussed, and the economic significance of these minerals is considered. There is no salt production reported from Alberta in 1928.

Jan 1, 1929

The most expensive unit operation in the beneficiation of ores is grinding. The correct design of the grinding circuit is crucial to prevent unnecessary use of energy. Proper design and evaluation of SAG grinding circuits require the specific grinding energy, which is determined experimentally. The most common tests in SAG grinding are the Drop Weight Test, from the Julius Kruttschnitt Mineral Research Center (JKMRC) in Australia, and the SAG Power Index, from MinnovEX Technologies in Canada. The application of these tests to the same ore sample commonly produces different results. The work reported here aims at comparing the application of these two tests in the determination of the specific grinding energy for sulfide copper ores from Sequeirinho and Sossego deposits, Sossego Project, Companhia Vale do Rio Doce - CVRD, in Para state, Brazil.

Jan 1, 2007

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By M. Hitch, M. B. Lytle

Resource development conflicts arise largely due to differences in worldview between those who support and those who oppose development. This paper illustrates how societies and civilizations with different worldviews produce different levels of creative and economic energy. A questionnaire was created to build a database of responses to test whether worldview and resource development are correlated. Factor and multivariate regression analysis determined correlations for respondent groupings. Results showed a positive correlation between the respondents\u2019 worldviews and their attitudes toward resource development. Correlations became stronger as the homogeneity of the sample subgroups increased.

Jan 1, 2017

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler's ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

By F. R. Archibald

A STATEMENT on this subject by A. D. Turnbull, presented and discussed at the Annual Business Conference of the Metallurgy Division, C.I.M., held in Ottawa on April 22nd 1957, led to creation of a committee "too see if the Metallurgy Division of the C.I.M. can improve this situation". Without discounting the general problems of education and short-ages in other fields, the committee is primarily concerned with deficiencies related to metallurgy. The committee members are: F. R. Archibald, Chairman, A. D. Turnbull, L. E. Djingheuzian, J. U. Mac-Ewan, and L. M. Pidgeon. Following exchange of views among the committee members a general attitude of approach was established and a background of reference material assembled. It is the purpose of this review to acquaint those interested with the reference material, to offer an appraisal of the situation, and to suggest a programme for action by the Metallurgy Division of the C.I.M. Before proceeding with the ?presentation it is fitting to point out that, notwithstanding some rather important developments in public concern for educational matters, as well as changes in the level of activity in the metallurgical industry, the statement (April 1957) by Mr. Turnbull still stands as a sound article of reference.

Jan 1, 1958

By F. Daniel Rosenkranz, Peter L. Silveston

Experiments investigating the treatment of a ground wood white water waste from an Ontario pulp and paper mill by an HVCB coal are reported. Adsorption capacity for the waste, with a soluble COD contribution of 2,100 mg/I, amounted to 0.17 per cent, by weight, of the Nova Scotia coal used. Percolation of the white water waste through a coal bed indicated that soluble COD is removed. For finely ground coals, over 90 per cent of the suspended solids in the waste are retained on the coal. Plugging of the coal bed is rapid, so that any treating process using filtration would have to renew the surface of the bed frequently.

Jan 1, 1970

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931