Search Documents

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By R. A. King, B. G. Hunt, C. E. T. White

"This paper reviews the history, occurrence, properties, and uses of indium, and describes the commercial production and fabrication of that metal by The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), at Trail, B.C'. Indium is produced commercially at Trail from dross retreatment furnace D.R.F.) slag, a complex by-product of the lead smelting operations. Furnace feed prepared from this slag is smelted with coke and limerock in an electric furnace. The e1ectric furnace bullion is parted electrolytically, producing a market-able lead-tin alloy containing about 8 per cent tin, and leaving the indium in the anode slime. Recovery of indium from the anode slime involves roasting the slime with sulphuric acid, followed by leaching with water, purifying the leach solution, recovering the indium by sponging with zinc or aluminum, and re-fining electrolytically. This process yields standard grade (99.97+ per cent) indium which is either sold or refined •to high purity ( 99.999 per cent) indium for special uses requiring higher purity metal."

Jan 1, 1959

By L. R. Bower

"This paper describes a highly versatile variable speed unit with a torque multiplication feature as a direct replacement for a fluid coupling .The unit is comprised of a modulating clutch with torque converter and lock-up options.The UCD does not start or stop the motor. This is carried out in the normal manner.The UCD continually monitors and rapidly regulates the output speed to the requirement of a set point demand from input signals or a pre-set program with full manual override.The pre-set program can include start and stop ramps, top speed and minimum speed regulation and also mid-speed set point with security for man-riding, etc. Speed variation is from zero to 100% on a constant duty basis.The input signals can be from any source, e.g. belt weigher. load profile bunker probes, mine monitoring system, etc.The UCD when fitted with a torque converter has a torque multiplication feature which automatically provides a starting torque up to two and a half times greater than the full load torque without exceeding the normal motor power levels.IntroductionIt is common practice in the mining industry to drive conveyors, whether they be belt or chain, through a transmission system incorporating a fluid coupling between the driving motor and gear-box .However, there are drawbacks and in an effort to attain a better degree of drive and control, two-speed motors - inverters cycle- converters - hydrostatic drives, etc ., have been introduced."

Jan 1, 1986

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By J. A. Cox, R. S. Mattson

"One of the main problems encountered in employing sublevel caving is the inherent high dilution factor. The operating results at Granduc illustrate that this dilution can be closely controlled and satisfactory recoveries achieved, in base metal ores grading less than 2.0% copper equivalent, by using an assay grade control system based on the fundamental draw characteristics. The history of draw control procedures employed since the start of operations provides an effective comparison between this system and one based mainly on tonnage. The transverse and longitudinal sublevel caving mining methods are described and it is shown how improvements in design layout, operating practice and draw control in narrow complex ore zones (12-foot minimum width) have raised the operating performance of the longitudinal system to a satisfactory level."

Jan 1, 1973

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By R. A. Campbell, R. R. Rogers

"AbstractThe experiments described show that crude bismuth metal containing up to 5 per •cent lead, 0.14 per cent silver, 0.015 per cent copper, 0.02 per cent iron, .and small amounts of antimony, nickel, and tin may be refined to a bismuth content of 99.98 per cent by distillation followed by chlorination. It also is shown that bismuth trichloride of high ,purity may be produced by passing chlorine over hot •crude bismuth metal and allowing the resulting vapours to •condense in a cooler .part of the system.IntroductionBISMUTH is used in the production of alloys and pharmaceuticals. During 1952, the New York price for the refined metal was $2.25 per pound in ton lots.Some months-ago a Canadian producer requested the Mines Branch to investigate methods of refining the bismuth which they had been producing. Their crude product had been selling for $1.50 to $1.70 per pound and it was desired to increase its purity to at least 99.98 per cent so that it could be sold for $2.25 per pound."

Jan 1, 1955

By A. G. Slade

"This paper deals with the direct application of rock mechanics in the underground mines at the Sudbury Operations of Falconbridge Nickel Mines Ltd. It covers mining methods, the use of photoelastic models, the fore-casting of rock strains and their elimination, closure methods and other common methods of ground control.INTRODUCTIONROCK MECHANICS IS A STUDY IN ROCK BEHAVIOUR and, although it is being termed a new science, it has been practiced since the industry began. Every person involved with rock excavations, from the mine superintendent to the stope driller, is actually practising rock mechanics. They probably call it by another name -experience, and applications of this knowledge are in evidence throughout the Falconbridge operations. Only in recent years have formal rock mechanics studies been employed to provide technical assistance to the mine operators in their primary objective of producing ore safely."

Jan 1, 1968

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

Sherwood?s Minto Project ? High grade copper copper-gold deposit ? Yukon Territory, Canada ? Development underway ? Permitted ? Production by mid mid-2007 ? 40 40-50m lbs Cu plus Au/Ag by by-products ? Parallel exploration program underway ?Discover more high grade resources ?But what kind of deposit is it?

May 1, 2006

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By C. I. Godwin

"The relative-value (R-value), discrimination-factor (D-factor), and vector-ratio (V-ratio) method (RDVM) provides a geological knowledge-based statistical and geological-genetic interpretation scheme for geochemical data that enhances discovery in geochemical exploration. The practical advantage of RDVM is that it synthesizes geochemical features geologically related to ore-deposit discovery in three steps: reclassifying element concentrations using log-probability plots into R-values; calculating geologically defined D-factors from R-values; and determining V-ratios. D-factors are the sum of R-values, divided by the number of R-values summed. Based on the analyses selected, D-factors mimic rock or mineral deposit signatures. V-ratios refine interpretations of rock type and vector to orebody locations.RÉSUMÉ La méthode de la valeur relative (valeur R), du facteur de discrimination (facteur D) et du rapport de vecteurs (rapport V) (RDVM), fournit un schéma d’interprétation des données géochimiques basé sur les statistiques et les connaissances géologiques et la génétique géologique; ce schéma contribue aux découvertes en exploration géochimique. L’avantage pratique de la RDVM est qu’elle fait la synthèse des caractéristiques géochimiques reliées géologiquement à des découvertes de gisements de minerais en trois étapes : une reclassification des concentrations des éléments au moyen de courbes de probabilité logarithmique en valeurs R; un calcul des facteurs D définis géologiquement à partir des valeurs R et la détermination des rapports V. Les facteurs D sont la somme des valeurs R divisés par le nombre de valeurs R additionnées. Selon les analyses choisies, les facteurs D imitent les signatures de la roche ou des gisements minéraux. Les rapports V peaufinent les interprétations des types de roches et dirigent vers des emplacements de gisements."

Jan 1, 2016

By J. M. Ortiz, J. P. Bertini

"In mineral resource and ore reserve estimation, several sources of information are generally available, such as diamond drillholes, reversed-circulation drillholes, and blastholes, and originate from one or more sampling campaigns and are analyzed by one or more laboratories. In such a situation, the grade measurements may not have the same precision and one should distinguish between hard and imprecise data.This work aims at studying the impact of data imprecision in resource/reserve evaluation through two case studies on simulated deposits: a porphyry copper deposit conditioned to real exploration and production data, and a gold deposit simulated without any conditioning data. Several geostatistical techniques are used to estimate the grades of selective mining units from exploration samples, including kriging, cokriging, lognormal and indicator kriging. Two types of imprecision are examined— measurements with multiplicative errors and measurements defined as intervals. The results are compared to the simulated grades of the selective mining units from a statistical and economic viewpoint.The study concludes that imprecise measurements should never be discarded because they help to improve the estimates, and that simple methods such as kriging are as efficient as more sophisticated ones for resource/reserve assessment. Finally, a few indications on how to diagnose and model the data imprecision are given."

Jan 1, 2005

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006