Search Documents

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By Rick Valenta

Is the Labrador Central Mineral Belt part of the IOCGU Club? ?I sent the club a wire stating, PLEASE ACCEPT MY RESIGNATION. I DON'T WANT TO BELONG TO ANY CLUB THAT WILL ACCEPT ME AS A MEMBER.? GrouchoMarx Acknowledgements ?Ian Dunlop, Matt Lennox-King, Mark O?Dea, Dave Barbour, Derek Wilton, Lucas Marshall, Roland Butler, Mark King, Sally Howson,

May 1, 2006

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By J. A. Pigott, R J. Hall

The International Nickel Company of Canada, Limited operates five underground mines on the rim of the Sudbury Basin in the northern part of the Province of Ontario. Four of the mines, the Frood-Stobie, Creigh-ton, Murray and Garson, are located on the south range of the basin with-in a radius of IO miles of the centre of the city of Sudbury. The fifth mine, Levack, is on the north range about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite and pyrrhotite. In 1960 the total ore production was in excess of 16 mil-lion tons, 95 per cent of which was produced from the five underground mines and the balance from the Frood-Stobie Open Pit. Mining at this open pit is nearing completion and underground production has been expanded to replace the open pit tonnage.

Jan 1, 1961

By W. D. C. MacKenzie

IT IS almost exactly fifteen years since the discovery of the Leduc oil field and, as this luncheon is part of the Thirteenth Annual Technical Meeting of the Institute's Petroleum and Natural Gas Division, it seems, therefore, a singularly appropriate time to discuss the theme which the program committee has suggested for the occasion -the progress of the Canadian oil industry during the fifteen years since the discovery of the Leduc field. As you will see, I plan to take a few minor liberties with this suggested theme. I shall present ample evidence of growth and progress, but, at the same time, I want to refer to some areas where progress has been anything but conspicuous and to see what can be learned from these areas for the future. The achievements of the Canadian oil industry since the Leduc discovery in 1947 have been substantial, and the public is relatively familiar with the more spectacular developments.

Jan 1, 1962

By C. W. MacLeod

LOCATION The Goudreau gold area in Ontario extends from a point a short distance south of the main line of the Canadian Pacific railway, at Lochalsh, in a south-westerly direction to the Magpie river. It crosses the Algoma Central & Hudson's Bay railway at Goudreau station, 177 miles north of Sault Ste. Marie. The area is roughly 25 miles in length by 6 miles in width. The potential gold formation is much more extensive but little prospecting has been done outside of the limits mentioned. The actual continuous area of Keewatin formation, in which gold has been found, is one of the largest in Ontario. ACCESSIBILITY Probably no mining area in a similar stage of development has had the excellent transportation facilities which Goudreau enjoys. This field is traversed in part by the main lines of the Canadian Pacific and Algoma Central railways. The Provincial Government has constructed 22 miles of road through the heart of the camp. Sixteen miles of this road is suitable for motor car traffic and several cars and trucks are in constant service.

Jan 1, 1926

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By Shigeru Sarata

A wheel loader is one of the main loading machines in open pit mines. The authors have been conducting research and development on autonomous operation of loading by a wheel loader. The most common loading method by a wheel loader is the ?V shape? path method. The loading operation consists of cycles of scooping from the pile, traveling to the dump truck, loading on the dump truck and return traveling to the scooping point for the next cycle. The traveling path includes a switchback in the middle of the path. The moving direction of the loader is changed at the switchback point. From observation of V shape path loading operations by experienced human operators, it seems that they control the bucket position between the scooping point and loading point on a shorter path for higher productivity. A new path planning method is proposed this paper, whereby a point on the center of the tip of the bucket is controlled moving from the initial point and the final point. The motion of the controlled point is generated by the wheel steering the wheel loader. The controlled point is moved along the direction to the final point; however, the motion and mechanism of wheel loader have restrictions, such as the velocity of the loader, the steering angle, and the steering angular velocity. Because of these restrictions, the path of the controlled point is not a straight line between the initial and final points. When this control method is applied between the scooping and the dumping points directly, the planned path is not stable in the leaving wing of V shape path. Therefore, the initial position of the wheel loader is set at the switchback point, then two approach wings to the scooping and the dumping points are made. The whole planned path is obtained by connecting the two paths. The shape of the planned path is strongly affected by the position of the switchback point, as well as the scooping and the dumping points. By simulation of path planning at different switchback points with the combination of the scooping and the dumping points, the paths for more effective loading are determined. The results of the simulation are presented in the paper.

Aug 1, 2013

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By P. D. Kondos, J. R. Goode

Given the global inventory of low grade and refractory gold deposits, processes that could turn these challenged deposits into mines are of considerable interest. Such gold deposits have low value and potentially high operating costs and so they pose special challenges for the mining engineer and metallurgist. Conventionally, refractory gold ores have been processed by whole ore pressure oxidation and roasting, or flotation followed by roasting, pressure oxidation or bio-oxidation of the concentrate. Halide-based processes have recently been developed that might be applied to concentrates. Low grade refractory gold ores have been processed using heap bio-oxidation followed by cyanide heap leaching or milling. Other processes are emerging. Barrick has completed an inventory of emerging technologies (1). A summary of the current status of these developments will be presented with the view that, with additional development, some of these technologies or a combination thereof may unlock the value of these deposits.

Jan 1, 2005

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By T. R. Kostecki, K. V. Jessu

"Roof bolts are subjected to axial stresses, shear stresses, or both. Axial and shear stresses were compared between roof bolts machined with two and three slots. Shear stresses perpendicular to and at an angle to the shear planes were evaluated by analyzing a three-slot instrumented roof bolt, performing laboratory tests on two- and three-slot roof bolts, and conducting in-situ test analyses. Threeslot bolts appear to provide a complete bending strain profile, requiring no prior knowledge of the estimated shear-plane orientation. Minimum displacements occur in roof bolts installed perpendicular to rather than at an angle to the shear planes.RÉSUMÉ Les boulons d’ancrage dans le toit d’une mine sont sujets à des contraintes axiales, des contraintes de cisaillement ou les deux. On a comparé les contraintes axiales et de cisaillement de boulons d’ancrage usinés avec deux ou trois fentes. Les contraintes de cisaillement perpendiculaires et à angle aux plans de cisaillement ont été évaluées en analysant un boulon d’ancrage de toit à trois fentes, en effectuant des essais en laboratoire sur des boulons d’ancrage de toit à deux et à trois fentes et en effectuant des analyses de tests in situ. Les boulons à trois fentes semblent fournir un profil complet de résistance aux contraintes de flexion, sans avoir besoin de connaître l’orientation estimée du plan de cisaillement. Des déplacements minimums ont lieu dans les boulons d’ancrage de toit installés perpendiculairement, plutôt qu’à un angle, aux plans de cisaillement."

Jan 1, 2016

By Mario Gerards, Axel Wellendorf, Arulnesan Rajesh

"In times of increasing energy cost and global demand for improved machine technology, the optimization of industrial mineral processes in terms of efficiency and production cost is an important factor when choosing industrial equipment suppliers. Of course this applies for screening machines, feeders and distributers as well!Besides of the ability of a screening machine for being adjustable to changing requirements during the production process itself, it becomes more and more important to choose the correct screening machine type, peripheral equipment for arising screening tasks and to optimize the overall design of the screening machine starting at a very early stage.The different types of screening machines bring many advantages and disadvantages with them. The selection of the correct type of screening machine can improve the flow rate, energy, efficiency, yield, quality, output, availability and decrease the maintenance costs and structural steel work.The machine optimization has to be a consecutive process in which at any time results of simulation and “real-life measurement” are compared and the findings are implemented in machine development and design. As an example, it is possible to reduce machine weight and reinforce the steel structure of a screening machine at the same time, which enables the manufacturer to use smaller drives for the screen.This paper will present the methods ANSYS and 3D Solid Works used at RHEWUM GmbH for this way of optimizing machine design and construction and examples for results gained from this continuous improvement process."

Jan 1, 2016

By M. J. Medd, G. A. Speirs

"This paper describes the simultaneous sinking and equipping of a 4.9 m diameter concrete-lined shaft to a projected depth of 1660 m. The shaft blast design utilizes the full face method using a parallel hole burn cut. Hydraulic drilling and a totally redesigned Cryderman-type mucking unit were integrated into the four deck sinking stage to provide for drilling, mucking, concreting and shaft steel equipping operations. A safety program was tailored and implemented specifically for this shaft sinking project.IntroductionIn July 1988, Falconbridge Limited commenced development of its Thayer Lindsley exploration site located some four km north of Sudbury on Regional Road 80.The first phase of this project was awarded to J .S. Redpath Mining Consultants Limited and the scope of work included the engineering and project management to construct a surface plant capable of supporting a shaft sinking and exploration program for potential future mine development. This initial phase of the project was completed on schedule and under budget on December 23, 1988, and is the subject of an independent paper.In November 1988, J.S. Redpath Limited was awarded the shaft sinking and exploration phase of this project. The scope of work consisted of sinking and equipping a 4.9 m diameter shaft to a depth of 1660 m and carrying out the development and diamond drilling on two levels. This work was scheduled to be completed by November 1991.The T .L. Exploration Project is located toward the eastern end of the south range of the Sudbury basin, north of Sudbury. Figure 1 details the projected mining area and the shaft location on the geological complex. Figure 2 is a section showing the exploration shaft that is located in the Norite. Two levels will be developed from this shaft, on the 1310m and 1588 m levels, to provide access for further geological examination of the ore bodies."

Jan 1, 1991

Who is CIBC? ? Canadian Imperial Bank of Commerce (?CIBC?) is a leading North American financial institution. ? Total Assets: US$315 billion ? Market Capitalization: US$29 billion ? CIBC comprises three strategic business lines: ? CIBC Retail Bank ? CIBC Wealth Management ? CIBC Wholesale Bank ? CIBC Wholesale Bank is a leading North American investment bank with niche capabilities in Asia, Australia & Europe. ? 1,000 + employees around the world ? Product range includes: Mergers & Acquisitions advisory and financing, Equity and Debt issues, Merchant Banking and Strategic Lending ? CIBC is ranked as the #1 investment bank in Canada across most of its key products and industries ? #1 Equity Underwriter in Canada ? #1 Mergers & Acquisitions Advisor in Canada

May 1, 2010

By Rick Coleman, Chelvan (Chevy) Veloo

"P.T. Freeport Indonesia's lrian Jaya Operation has been producing copper concentrate continuously since 1972. Numerous ore discoveries and five mill expansion programs have seen the initial milling rate of 7,200 MTPD escalate to the present rate of 125,000 MTPD, producing 2.5 million pounds of copper and 3,500 troy ounces of gold per day. The latest expansion, commissioned in February 1995, incorporates a 34 foot Semi- Autogenous Grinding (SAG) Mill, two 20'x30' Ball Mills, conventional roughing, cleaner column flotation, and attendant upgrades to the existing concentrate pumping and dewatering facilities. This paper will describe the SAG Plant flowsheet, and focus on the key training issues which contributed to a successful plant start-up.IntroductionP.T. Freeport Indonesia's operations in the Ertsberg mining district are located in the Jayawijaya Mountains of Irian Jaya, the easternmost province of the Republic of Indonesia. P.T. Freeport Indonesia (PTFI), the operator, is owned by Freeport MacMoRan Copper and Gold (81.3%), the Government of Indonesia (9.4%), and private Indonesian investors (9.4%). Geographical location, and sailing distances are provided on the attached location map.The operation stretches over 7 4 miles ( 114 km) from the dewatering and concentrate shipping facility at the Port of Amamapare on the Arafura Sea to the Grasberg open pit located at 3400m. The regional geology is covered in detail by Van Nort et al (1991 ), with current proven and probable reserves estimated at 1.13 billion metric tonnes grading 1.30% Copper, 1.42 ppm Gold, and 4.06 ppm Silver. The Grasberg open pit mining operation provides 92% of the mill feed, and is described in detail by Hickson (1991). The remainder of the mill feed is derived from several underground block caving operations. Current production rates provide a mine life in excess of 25 years. However, very favorable geology in the area leads to expectations that additional reserves will extend the life of the operation considerably."

Jan 1, 1996

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019